Botslab Outdoor Dual-Lens Camera

Quick Start Guide

This document provides a quick start guide for the Botslab Outdoor Dual-Lens Camera.

Packing List

Please check whether the main unit and all accessories are complete upon unpacking.

• Camera host x 1
• Bracket x 1
• Screw pack x 1
• Warning sticker x 1
• Quick Start Guide x 1
• Positioning sticker x 1
• Power adapter x 1
• Screwdriver x 1

Due to ongoing updates and iteration of the product, there may be slight differences between the physical and schematic diagrams. Please refer to the actual products for the most accurate information.

Product Appearance

Diagram illustrating the camera's front and back views with labeled components:

• Antenna
• Camera lens
• Microphone
• Indicator light
• White LED light
• IR light
• Micro SD Card slot
• Reset button
• Speaker
• Power interface

Memory card support: Maximum 256GB.

Guideline for Connecting to the Network

Download and Install the APP

Method 1: Scan the QR code below with your mobile phone to download and install the Botslab APP.

Method 2: Search and download the Botslab APP from App Store or Google Play, and then install it.

[Text description: QR code for scanning to download Botslab APP]

[Text description: Button/Link: Available on the App Store]

[Text description: Button/Link: Android app on Google Play]

Connection Guide

Before using the app to add a camera, please refer to the following diagram and connect the camera according to the prompts below.

• Connect the camera to the power supply.

Diagram showing the camera host connected to a power adapter, which is plugged into an electrical socket.

Add the Device

Method 1

After logging in, Bluetooth will automatically search for the camera by default. Once the camera is found, add the device according to the prompts.

[App screenshot description: Shows "Outdoor Dual-Lens Camera -0291" and a "Connect to a network" button]

Method 2

After logging in, click the "+" button on the upper right corner of the homepage, select "Scan" and use your mobile phone to scan the QR code on the camera. This will direct you to the network setup page. Follow the prompts to add the camera.

[Diagram description: Shows app interface with "+" button, "Scan" option, and a hand holding a phone scanning a QR code on the camera.]

Method 3

After logging in, click the "+" button in the upper right corner of the APP homepage and add the “Botslab Outdoor Dual-Lens Camera W302" by model.

[App screenshot description: Shows "Add device" interface with "Automatically searching for nearby devices..." and a list of recommended devices, including "Outdoor Dual-Lens Camera W302".]

Installation Guide

Installation Method

1. Please use the original adapter to prevent overvoltage and overcurrent from damaging the product.

2. Pay attention to outdoor lightning protection measures.

Diagram description: Wall-mounted installation.

Diagram description: Ceiling installation.

Antenna Installation and Adjustment

When the antenna is parallel to the camera, it can affect signal reception.

[Diagram description: Example of correct antenna position] ✔️

[Diagram description: Example of correct antenna position] ✔️

[Diagram description: Example of incorrect antenna position] ❌

Installation Bracket

1. Attach the positioning sticker to the wall and drill a hole according to the position shown in the diagram.

2. Insert the expansion bolt into the wall at the positioning sticker's hole position.

3. Fix the bracket base with screws.

Diagram description: Shows wall surface, positioning sticker, expansion bolt, wall bracket, screws, and video camera assembly.

Installation of the Camera

1. Rotate the camera body and screw it into the bracket. Adjust the camera position, and view the image's fixed position through the app.

2. Tighten the bracket by rotating the nuts and bracket base.

3. Adjust and unfold the antenna to the appropriate position.

Diagram description: Shows camera body being attached to the bracket with a knob.

Precautions

1. To achieve better night vision imaging results, keep the lens front or side away from reflective objects such as glass and white walls. This will prevent nearby objects from appearing too bright while distant objects may appear dark or white.

2. Place the device in a location with good network signal reception and keep it away from metal objects (such as metal brackets, metal doors, and windows) or other sources of signal interference.

3. It is normal that the equipment generates heat during operation.

4. This product is designed to operate within a temperature range of -20°C to +60°C. Do not use this product in environments that are too hot or too cold.

5. Please use the original power cord to ensure safety of power supply and good user experience.

Working Status Description

The manufacturer reserves the right to adjust the product's functional status through firmware upgrades or software adjustments.

Important Statement

Personal Information Security

For the safety of you and your family, please make sure that the products you purchase are not bound to any unauthorized person. Botslab will take strict measures to protect the information security of you and your family.

Description of Hazardous Material Contents

This form is prepared in accordance with SJ/T11364.

[Note: The symbols ⚪ and ❌ in the original document indicate compliance status. ⚪ means 'Below requirements', and ❌ means 'Exceeds limit' but satisfies exemption requirements.]

Remarks

The lead content in a small number of special-purpose SMT electronic components (such as high-voltage resistors, ceramic resistors, diodes, etc.) in the part labeled "x" in the above table may be ≥ 0.1%. The lead content in screws or cores of data cables can be ≥0.1% due to the adoption of high-performance alloy. These components are in compliance with exemption clauses of the EU RoHS Directive. At this stage, due to the limitations of the global technological development level, there is no alternative technologies and parts, and the lead content of the external contactable parts of the product meets the environmental protection requirements.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

After-Sales Service

Warranty Policy for Botslab Video Doorbell

This product comes with a one-year Local Warranty Service. For detail of warranty service, please kindly contact local Authorized Distributors in your country.

Non-warranty Policy for Botslab Video Doorbell

• No valid warranty certificate and purchase invoice.
• Damage caused by use, maintenance, or keeping of the product not in accordance with product description, damage caused by disassembly and repair unauthorized by Botslab, or artificial damage.
• Damages that result from force majeure.
• Normal decoloration and wastage during usage will not be included in warranty service.

Contact Us

• ? https://www.botslab.com
• ✉️ service@botslab.com
• f Facebook@botslabofficial
• ? 1-866-360-0505 (Only for US)
• Working time: Mon-Fri, 9:00 - 17:00 EST

CE Declaration of Conformity

This product complies with the radio interference requirements of the European community. Hereby, Botslab, Inc. declares that the product is in compliance with the essential requirements and other relevant provisions of RE Directive 2014/53/EU. You can find the Declaration of Conformity on http://www.botslab.com. In accordance with Article 10(2) and Article 10(10), This product is allowed to be used in all EU member states.

The device is restricted to indoor use when operated in the European Community using frequency 5150MHz-5250MHz to reduce the potential for interference.

The device complies with RF specifications when the device used at least 20cm from your body.

RF power: XXXXX

RF frequency band: XXXXXX

The operating temperature of the product is: XXXXXX

❗

Manufacturer Name: Botslab Inc.

Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA

Product Name: Botslab Outdoor Dual-Lens Camera

Trademark: Botslab

Product Model: W302