Botslab P100A Security Camera

Introduction

Thank you for purchasing this camera. It is designed to be extremely portable and can be used in different applications, aiming to bring you convenience and safety in daily life. Please follow this user guide to set up your camera correctly.

Contents

• 1. Preparation
• 2. Wi-Fi remote monitoring operation
• 3. Common issue and notices
• 4. Notices for memory card
• 5. FCC Warning

1. Preparation

1.1 Reset Camera

Reset method: Long touch the 'reset' button for 5 seconds. The process is completed after hearing a beep, and then wait for the restart.

[Reset Button]

1.2 APP Download

Scan the QR code to download the APP 'Botslab'.

Android smartphones can search for 'Botslab' in Google Play to download.

iPhones can search for 'Botslab' in the APP store to download.

[QR Code for Botslab APP]

1.3 Sign For Your Account

Open the downloaded APP, click 'Register', choose to sign up by phone number or email. After entering the verification code and setting a password, sign-up is completed.

Notice: You should choose your location correctly when you log in.

[Location Selection - e.g., Singapore]

2. Wi-Fi remote monitoring operation

a. Guide for Android Phone

1. After preparation is finished, open the APP 'Botslab'. It will search for the device nearby automatically and pop-ups will be shown as the picture on the right.
2. Click 'Start to connect'.
3. Choose Wi-Fi and enter the password to connect, then click 'Next Step'. The Wi-Fi should be 2.4GHz and without any special marks.
4. Click 'Connect' to the device's hotspot, as shown in the picture below.
5. Wait for network setup. You can start to use the camera once it shows 'set succeed'.

Note: If the connection fails, please reset the camera and follow the guide to operate again.

[Botslab APP Interface - Android]

b. Guide for iOS/ iPhone

1. Open the APP 'Botslab'.
2. Click 'Add' and then scan the QR code at the bottom of the device, as shown in the picture on the right.
3. Click 'Add' at the top right corner to select the device, as shown in the picture on the right. Choose 'Camera' -- 'Camera Wi-Fi', as shown below.
4. At the top right corner, the default mode of network connection should be 'Wi-Fi Quick connect'. Botslab supports two modes: 'Wi-Fi Quick Connect' and 'QR Code Connect'. Make sure it shows 'Wi-Fi Quick connect' and click 'Next Step' as shown in the right picture.
5. Choose Wi-Fi and enter the password to connect, then click 'Next Step'. The Wi-Fi should be 2.4GHz and without any special marks.
6. Click 'Go to connect Wi-Fi', and it will jump to the phone's Wi-Fi settings. Connect to the Wi-Fi called 'FC************'. Once connected, return to Botslab and wait for the setting. Once it shows 'set succeed', you can start to use the camera.

[Botslab APP Interface - iOS]

3. Common issue and notices

• 3.1 When logging into Botslab, please ensure you select the correct location of the camera. Otherwise, you may not be able to add the device or it may always be offline.
• 3.2 The camera only supports 2.4G Wi-Fi. Do not choose 5G Wi-Fi.
• 3.3 The camera can only be activated by one account. It needs to be cancelled from the current account to be activated by another account.
• 3.4 Camera sharing: The camera image can be shared with a maximum of 5 accounts, but they cannot watch simultaneously.

4. Notices for memory card

• 4.1 Insert the TF card when the camera is powered off. Note the insertion direction, then power up the camera.
• 4.2 Supported SD card format: FAT32. It is recommended to format the SD card after a successful connection.
• 4.3 Recordings will overwrite automatically when the memory is full.
• 4.4 The maximum memory capacity is 32GB.

5. FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.