Waterdrop WD-G3P600 RO Water Filter System
Instruction Manual
1. Parts List
Inspect the package as parts list first. Identify and get familiar with all components for quick installation.
Main Unit & Filters:
- System Housing X 1 Set
- WD-G3-CB X1 (Activated Carbon Filter)
- WD-G3-CF X1 (Pre-sediment and Carbon Block Filter)
- WD-G3P600-RO X1 (Reverse Osmosis Membrane Filter)
Faucets & Tubing:
- Smart Digital RO Faucet x1
- White 1/4" PE Tubing X60" (Preinstalled ✔️)
- Feed Water Adapter 3/8"-1/2" X 1 Set
- White 3/8" PE Tubing X 60" (Preinstalled ✔️)
- Red 1/4" PE Tubing X 60"
Installation Hardware:
- Drain Saddle 1/4" X 1 Set
- Lock Clip X5 ?
- Teflon Tape X1
- Power Adapter X 1 Set
2. Sample Connection
Diagram illustrating the RO system connections. Labels A-O indicate various components.
- A Filter Life Indicator
- B Display Screen: TDS Reading, Flushing Status, Malfunction Code
- C Activated Carbon Filter (CB)
- D Pre-sediment and Carbon Block Filter (CF)
- E Reverse Osmosis Membrane Filter (RO)
- F "POWER" Port ?
- G "FAUCET" connector
- H "INPUT" Water Port
- I "FILTERED" Water Port
- J "WASTE" Water Port
- K Feed Water Adapter
- L Preinstalled Filtered Water Tubing With Faucet
- M Drain Saddle
- N Power Socket
- O Faucet Power Cord
3. Quick Installation
Before installation, please note:
- The RO system must be connected to the COLD water supply only.
- Do not install the system in exposure to direct sunlight or harmful chemicals, nor any place where it may be damaged.
Installation Steps:
-
Step 1: Install the Feed Water Adapter (K)
Turn off cold water supply valve. Connect the feed water adapter to your cold water supply pipe.
-
Step 2: Install the RO Faucet and UV sterilizer (Non-Air Gap Faucet)
If your kitchen sink or countertop does not have an existing hole, you will have to drill one (1") referring to the Instruction Manual. Insert the faucet head into faucet body. Insert faucet stem and power cord into the hole on countertop. Under the sink, slip on other parts in the order as shown. Connect the outlet of UV sterilizer to PE tubing on faucet tightly, then insert the lock clip. Connect the inlet of UV sterilizer to the other end of PE tubing, then insert the lock clip.
-
Step 3: Install the Drain Saddle (M)
Choose a spot on the vertical drain pipe as high as possible and drill a 1/4" hole. Use the "WASTE" water tubing as a guide to position the drain saddle by tightening screws and nuts evenly.
-
Step 4: Position the RO System Housing
An ample flat area is required to place the system housing. Position the front panel facing towards you for future indicator checking.
-
Step 5: Connect the Tubings
Ensure each tubing is inserted firmly and fully until it reaches the mark on the end of the tubing.
- Connect the "INPUT" water tubing from feed water adapter (K) to "INPUT" water port (H).
- Connect the "FILTERED" water tubing from RO faucet (L) to "FILTERED" water port (I).
- Connect the "WASTE" water tubing from drain saddle (M) to "WASTE" water port (J).
-
Step 6: Connect Power Cord
Connect Power Adapter to power port (F). Connect faucet power cord into "Faucet" connector (O-G).
-
Step 7: Install the Filters
Insert the filter into its corresponding hole. Rotate the filter clockwise 1/4 turn. You may hear a clicking sound when the filter is fitted properly.
-
Step 8: Start Up the System
Turn on cold water supply valve and feed water adapter, connect power adapter. Wait for 5 minutes for the system to flush automatically. Turn on RO faucet, allow it to run 30 minutes until the display screen shows TDS reading.
4. Display Screen and Filter Life Reminder
Display Screens:
- TDS Display: The built-in TDS sensor detects water quality. The front panel screen and RO faucet screen show TDS reading.
- Flushing Display: Every time the system flushes, the front panel screen and RO faucet screen show flushing status.
- Malfunction Display: When the system is in fault, the front panel screen and RO faucet screen show error codes (E02, E03, E04). Refer to the Instruction Manual for detailed solutions.
Filter Life Reminder:
Indicators on the system housing and RO faucet notify you for routine filter replacement by color change.
Indicator on System Housing:
- Good (Blue)
- Replace Soon (Yellow)
- Replace Now (Red)
Indicator on RO Faucet:
- Good (White)
- Replace Soon (Yellow)
- Replace Now (Red)
- Flushing (White flash)
- Malfunction (Red flash)
| Faucet | Remaining Life (Day) | Remaining Capacity (G) | Status |
|---|---|---|---|
| White | >15 | >40 | Good |
| Yellow | <15 | ≤40 | Replace Soon |
| Red | ≤0 | ≤0 | Replace Now |
| White flash (on RO Faucet) | / | / | Flushing |
| Red flash (on RO Faucet) | / | / | Malfunction |
NOTE: The indicators notify in accordance with usage time or processing capacity of the filters, whichever comes first.
Manufacturer Information
Waterdrop
Filter Better Live Healthier
Manufacturer Technical Support:
Tel: 1-888-352-3558 (U.S.)
E-mail: service@waterdropfilter.com
Made in China V043
Qingdao Ecopure Filter Co., Ltd. ⚙️
