Aqara LED Bulb T2 FAQ
About Aqara LED Bulb T2 Models and Versions
Aqara LED Bulb T2 comes in several models and versions, primarily differing in their socket types and color temperature capabilities:
- Models/Versions: E26, E27, GU10. These can be CCT (Color Correlated Temperature) or RGB CCT (Color Temperature) versions.
- Socket Differences: E26 and E27 are standard screw bases compatible with most lighting fixtures. GU10 is a bayonet-style fitting often used with compact fluorescent or LED lamps.
Supported Regions:
- E27 CCT / CCT RGB: EU (Europe), RU (Russia), AU (Australia), TW (Taiwan), Southeast Asia
- E26 CCT / CCT RGB: JA (Japan), KR (Korea), North America
- GU10 CCT / CCT RGB: Global
How to Install Aqara LED Bulb T2
- Ensure the power is off before installing the bulb into the socket.
- Screw the bulb in securely.
- Turn the power on. The light will illuminate automatically and then blink twice slowly, indicating it has entered pairing standby mode.
Aqara LED Bulb T2 Supported Protocols
The Aqara LED Bulb T2 supports both Thread and Zigbee communication protocols, offering flexibility for various user needs.
Using with Matter-compatible Ecosystems:
To use the bulb with a Matter-compatible ecosystem, you will need a compatible Matter controller and a Thread Border Router. For information on compatible controllers and routers, please contact Aqara customer service. The bulb can simultaneously connect with up to five ecosystems.
- Zigbee / Matter Mode: To enable Aqara Home compatibility, an Aqara Hub is required. The Aqara Hub's firmware must be updated to the latest version.
- Matter Mode: Aqara Hub M3
- Zigbee Mode: Aqara M2 / G3
Can Aqara LED Bulb T2 Use Thread and Zigbee Simultaneously?
No, simultaneous use of Thread and Zigbee is not supported. By default, the bulb is set to the Thread protocol (Matter). If you wish to switch to Zigbee mode, follow the setup instructions in the app and select the protocol during connection.
Can the Protocol be Switched After Connection?
Yes, it is possible. However, this requires the following steps:
- Remove the device from the app.
- Reconnect the device to the network, selecting the desired protocol during the connection process.
Note: Switching protocols will reset the bulb to its initial state, erasing all previous settings.
How to Reset / Initialize Aqara LED Bulb T2
1. Reset Method (Initialize Pairing Information):
- Turn the power switch on and off 5 times consecutively (on-off counts as one cycle).
- The light will blink twice quickly and then remain steadily lit, indicating a successful reset.
- This action only clears network information. Previous settings will be retained.
2. Factory Reset Method:
- Turn the power switch on and off 10 times consecutively (on-off counts as one cycle).
- Similar to the reset method, the light will blink twice quickly and remain steadily lit, indicating a successful initialization.
- This action will completely erase all settings.
Can Aqara LED Bulb T2 Be Used Without Network Connection?
Yes, the Aqara LED Bulb T2 can function as a regular light bulb when not connected to a network. However, app-based control and smart home integrations require a prior network connection.
Suitable Lighting Fixtures and Usage Scenarios for Aqara LED Bulb T2
The E26 / E27 / GU10 types are suitable for various lighting fixtures, including:
- Desk lamps
- Floor lamps
- Wall-mounted lights
- Downlights
- Ceiling lights
The GU10 type, due to its smaller size and narrower beam angle, is particularly well-suited for accent lighting and small fixtures.
Environment Not Recommended for Use:
- Fully enclosed light fixtures
- Outdoor use
- Dimmers with traditional knobs (knob-style switches)
Using the bulb in fully enclosed fixtures may cause overheating, potentially triggering the temperature protection function. It is recommended to use the bulb in open fixtures with good ventilation, away from other heat sources.
The bulb is not waterproof and should only be used in dry indoor environments.
Does it Support Dimmable Switches with Knobs?
No, it does not. The Aqara LED Bulb T2 is not compatible with traditional dimmable switches. Its operation is based on a different principle than incandescent or halogen bulbs, and using it with such switches may lead to malfunctions, flickering, or damage. For smart functionality, standard on/off switches or smart controllers are recommended.
