FEKA 600 SUBMERSIBLE PUMPS
Sewage Water Draining Submersible Pumps for Domestic Use
Technical Data
The FEKA 600 series offers versions with a special stainless steel pump shaft.
Operating Range: From 1 to 16 m³/h with a head up to 7.45 meters.
Liquid Temperature Range: 0 °C to +35 °C for domestic use.
Pumped Liquid: Cesspool sewage water.
Particle Size for Free Passage of Solids: Up to 25 mm through the suction grid.
| Feature | FEKA 600 | FEKA 600 A | FEKA 600 NA |
|---|---|---|---|
| Minimum Draught Depth | 25 mm | 175 mm | 38 mm |
Maximum Immersion Depth: 7 meters.
Maximum Dry Run Time: 1 minute.
Protection Class: IP 68.
Insulation Class: F.
Applications
The submersible pump of the FEKA series is suitable for lifting sewage water from cesspools. It is capable of handling suspended solid matter with sizes up to 25 mm.
The integrated level switch allows for fixed installation, ensuring automatic operation.
A version with a special stainless steel pump shaft (SV) is also available.
Construction Features
Pump Construction
Features a hydro-resistant technopolymer pump body, cover, and suction grid. The motor, rotor shaft, and bolts/screws are made of stainless steel. It incorporates a threefold seal with interposed rings and an oil pre-chamber for enhanced durability.
Motor Construction
The motor is a submersible type, continuous duty asynchronous motor. The stator is enclosed in an airtight stainless steel casing with an outer cover protecting the wiring and capacitor. The rotor runs on permanently lubricated, oversized ball bearings for low noise and durability. Standard built-in thermo-amperometric protection is included. Capacitors are permanently fitted on single-phase versions. For three-phase motors, the use of remote overload cut-outs is recommended, in compliance with local regulations.
Construction complies with standards CEI 2-3 and CEI 61-69 (EN 60335-2-41).
Materials
Key components and their materials:
| Part Number | Part Name | Material |
|---|---|---|
| 1 | Pump Body | Technopolymer |
| 4 | Impeller | Technopolymer |
| 29 | O-Ring | NBR |
| 32 | Stop Ring | Technopolymer |
| 54 | Motor Case | AISI 304 Stainless Steel (X5 CrNi 1810 - UNI 6900/71) |
| Rotor Shaft | Rotor Shaft | AISI 416 Stainless Steel (X12 CrS13 - UNI 6900/71) - For SV version, shaft is AISI 431 Stainless Steel |
| 78 | Adjustment Ring | Technopolymer |
| 79 | Suction Grid | Technopolymer |
| 83 | Float | Technopolymer |
* Materials in contact with the liquid.
Diagram Description: An exploded view of the submersible pump shows numbered components including the pump body (1), impeller (4), motor case (54), suction grid (79), and float (83).
Model Availability & Installation
| Model | With Float (A) | Without Float (NA) |
|---|---|---|
| FEKA 600 | YES | YES |
Minimum Well Size for Automatic Operation (Fixed Installation)
Diagram Description: A diagram illustrates the minimum dimensions required for a well to accommodate automatic operation. It shows a rectangular footprint with dimensions of 400 mm width and 600 mm height.
Performance Range
Performance curves are based on kinematic viscosity values of 1 mm²/s and a density of 1000 kg/m³. Curve tolerance is according to ISO 9906.
Diagram Description: A graphic selection table displays performance curves plotting Head (H) in meters (m) and kilopascals (kPa) against Flow Rate (Q) in cubic meters per hour (m³/h), liters per second (l/s), liters per minute (l/min), US gallons per minute (US gpm), and imperial gallons per minute (IMP gpm). The chart shows performance envelopes for various DAB submersible pump models, including the FEKA 600.
Selection Table - FEKA 600
| Model | Q (m³/h) | Q (l/min) | H (m) |
|---|---|---|---|
| FEKA 600 M-T | 0 | 0 | 7.45 |
| 3 | 50 | 6.45 | |
| 6 | 100 | 5.7 | |
| 9 | 150 | 4.95 | |
| 12 | 200 | 4.1 | |
| 15 | 250 | 2.8 | |
| 18 | 300 | - | |
| 24 | 400 | - | |
| 30 | 500 | - | |
| 36 | 600 | - |
Electrical and Dimensional Data
Electrical Data
Standard Voltages: Single-phase: 220-240 V / 50 Hz; Three-phase: 400 V / 50 Hz.
| Model | Power Input (50 Hz) | P1 MAX (kW) | P2 NOMINAL (kW) | HP | Current (A) | Capacitor (µF / Vc) |
|---|---|---|---|---|---|---|
| FEKA 600 M-A | 1 x 220-240 V~ | 0.94 | 0.55 | 0.75 | 4.3 | 14 / 450 |
| FEKA 600 T-NA | 3 x 400 V~ | 1 | 0.55 | 0.75 | 1.7 | - |
| FEKA 600 M-A SV* | 1 x 220-240 V~ | 0.94 | 0.55 | 0.75 | 4.3 | 14 / 450 |
| FEKA 600 M-NA SV* | 1 x 220-240 V~ | 1 | 0.55 | 0.75 | 4.3 | 14 / 450 |
| FEKA 600 T-NA SV* | 3 x 400 V~ | 1 | 0.55 | 0.75 | 1.7 | - |
* SV denotes version with special stainless steel pump shaft. A: Automatic with float; NA: Non-automatic, without float.
Standard Cables:
- Single-phase versions: 5 meter H05 RN-F for FEKA 600 M-A, 10 meter H07 RN-F for FEKA 600 M-NA.
- Three-phase versions: 5 meters H07 RN-F.
Standard Plug (Single-phase): SCHUKO CEE 7 - VII - UNEL 47166-68.
Dimensional Data
Diagram Description: Multiple diagrams illustrate pump dimensions. One shows a profile view with labels A, B, C, D, E, H, H1, H2, MIN. LEV., MAX. LEV., and DNM. Another diagram shows the suction grid with a gas outlet. The tables provide specific measurements for various models.
| Model | A (mm) | B (mm) | C (mm) | D (mm) | E (mm) | H (mm) | H1 (mm) | H2 (mm) | MIN. LEV. (mm) | MAX. LEV. (mm) | DNM GAS | PACKING DIMENSIONS (L/A x L/B x H) (mm) | CABLE | VOLUME (m³) | WEIGHT (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FEKA 600 M-A | 193 | 235 | 56 | 296 | 90 | 368 | 443 | 73 | 190 | 390 | 1½" | 287 x 202 x 431 | 5 mt. H05 | 0.025 | 7 |
| FEKA 600 T-NA | 162 | 160 | 56 | - | 90 | 368 | - | 73 | - | - | 1½" | 287 x 202 x 431 | 10 mt. H05 | 0.025 | 6.7 |
| FEKA 600 M-A SV* | 193 | 235 | 56 | 296 | 90 | 368 | 443 | 73 | 190 | 390 | 1½" | 287 x 202 x 431 | 5 mt. H05 | 0.025 | 7 |
| FEKA 600 (M-T)-NA SV* | 162 | 160 | 56 | - | 90 | 368 | - | 73 | - | - | 1½" | 287 x 202 x 431 | 10 mt. H05 | 0.025 | 6.7 |
DAB PUMPS reserves the right to make modifications without notice.
