Tchibo Shelving Unit Assembly Instructions

Introduction

Welcome! Please keep these instructions for future reference. If you pass this product to someone else, please include these assembly instructions. We hope you enjoy your new product.

Safety Information

DANGER: Risks to Children

• Keep packaging materials away from children. Bags and films are not toys. Ensure children do not pull them over their heads or swallow any parts. Risk of suffocation!
• The product contains small parts that can be life-threatening if swallowed. Keep children away during assembly.
• Keep infants away from the product as they may try to pull themselves up on it or climb onto it.

CAUTION: Risk of Injury and Material Damage

• Be careful during assembly to avoid pinching fingers in metal parts or injuring yourself on sharp edges or corners. Wear work gloves.
• Always place the product on a level, non-sloping surface.
• Do not stand or sit on the product, as it could tip over or be damaged.
• Do not place the product freely in a room or against a wall without securing it. For optimal stability, the product must be fastened to a suitable wall.
• Mounting materials (screws and wall plugs) are included for wall mounting. These are suitable for standard, solid walls. Before wall mounting, consult with a professional about the appropriate mounting materials for your specific wall. Ensure there are no pipes or electrical wiring behind the wall where you intend to drill.
• Assemble the product on a soft, even surface. Use the transport cardboard underneath to prevent scratching or damaging surfaces.
• Handle glass panes with care! Hold them firmly during assembly to prevent them from falling.
• Use the product only for its intended purpose and do not overload it.
• Do not open and load all flap doors simultaneously. Risk of tipping over!

Intended Use

This product is suitable for indoor use only. Protect it from moisture. It is designed for private household use and is not suitable for commercial purposes.

Care Instructions

• Do not use abrasive or caustic cleaning agents or hard brushes.
• Clean glass surfaces with a damp cloth, using glass cleaner if necessary, then wipe dry with a soft cloth.
• Clean other surfaces with a slightly damp cloth and wipe dry.

Unpacking and Disposal

Carefully remove all packaging material and dispose of it properly according to local recycling guidelines. Ensure you do not accidentally discard any assembly materials.

Parts List

The following replacement parts can be ordered. Please refer to the part numbers for ordering.

Assembly Steps

Step 1: Frame Assembly

Assemble the main frame using three units of part 1 and six units of part 2.

Step 2: Insert Rods

Insert six units of rod S1 into the frame.

Step 3: Align and Secure

Align the holes and insert screws. Use part J and screws S2 to connect the frame sections. Ensure holes are properly aligned.

Step 4: Hand-Tighten Rods

Turn the rods (part 3) hand-tight, but do not over-tighten.

Step 5: Partial Screw Tightening

Tighten all screws S2 only about 90% of the way.

Step 6: Insert Back Panels

Insert the back panels (part 4) into the frame.

Step 7: Secure Back Panels

Secure the back panels using screws S4.

Step 8: Configure Wide Section

Decide whether the wider section should be on the right or the left. The following instructions illustrate assembly option A.

Step 9: Attach Hinge Mechanisms to Side Panels

Attach hinge mechanisms (part 6a) to the side panels using screws S5 and part A.

Step 10: Attach Hinge Mechanisms to Bottom Panels

Attach hinge mechanisms (part 6b) to the bottom panels using screws S5 and part B.

Step 11: Attach Doors

Attach the doors (part 6a and 6b) to the frame using the previously attached hinge mechanisms. Listen for a "Click!" to confirm attachment.

Step 12: Insert Glass Shelves

Insert the glass shelves (part 5) into the unit.

Step 13: Attach Hinges to Glass Shelves

Attach hinge components (using part S6) to the glass shelves. Be careful when pulling out the hinge to avoid pinching your fingers.

Step 14: Insert Remaining Glass Shelves

Insert the remaining glass shelves (part 7).

Step 15: Final Screw Tightening

Insert the glass shelves (part 7) and then fully tighten all outer screws S2 (100%) to secure them. Ensure glass panes are laid on a soft surface before this step.

Step 16: Attach and Level Feet

Attach the adjustable feet (part C) to the bottom of the unit and level the unit by adjusting the feet.

Step 17: Attach Side Clips

Attach side clips/brackets (parts G, C) using screws S3.

Step 18: Final Assembly Check

Perform a final check of the assembly to ensure all parts are securely fitted.

Configuration Options

The unit can be configured in different ways depending on the placement of the rear panels. This manual illustrates assembly option A as an example.

Option A: Shows a configuration with the wider section on one side.

Option B: Shows an alternative configuration (placement of wider section to be decided by user).

Maximum load capacities are indicated: 40 kg for the main shelves, 8 kg for the upper shelf, and 5 kg for the smaller compartments.

Service and Contact Information

For product information, accessory or replacement part orders, or service inquiries, please contact Tchibo customer service. Please provide the article number and replacement part order number.

Germany: 040 60 02 79 00 | www.tchibo.de/service

Austria: 0800 400 235 | www.tchibo.at/service

Switzerland: 043 88 33 099 | www.tchibo.ch/service

General Contact: service@tchibo.de

Visit www.tchibo.de/anleitungen for more instructions.