Tchibo Assembly Instructions

Welcome

Dear Customer, please keep these assembly instructions for future reference. If you pass the article on to someone else, please also hand over these instructions. We hope you enjoy this product.

For Your Safety

DANGER: Risks for Children

Keep packaging material out of reach of children. Bags and films are not toys. Ensure children do not pull them over their heads or swallow parts. Risk of suffocation! The product contains small parts that can be life-threatening if swallowed. Keep children away during assembly. Keep infants away from the product as they may try to pull themselves up or climb on it.

CAUTION: Risk of Injury and Material Damage!

Be careful during assembly not to pinch fingers when installing metal parts or to injure yourself on sharp edges/corners. Wear work gloves! Always place the product on a level, non-sloping surface. Do not stand or sit on the product, as it could tip over or be damaged. Do not place the product freely in a room or against a wall without securing it. For optimal stability, the product must be fastened to a suitable wall. Wall mounting materials (screws and wall plugs) are included and are suitable for standard, solid walls. Before wall mounting, consult with a professional regarding suitable mounting materials for your specific wall. Ensure there are no pipes or electrical wiring behind the drilling location. Assemble the product on a soft, level surface, using the transport cardboard underneath to prevent scratches or damage to surfaces. Use the product only for its intended purpose and do not overload it. Do not open and load all folding doors simultaneously, as this poses a tipping hazard.

Intended Use

This product is suitable for indoor use only. Protect it from moisture. It is designed for private household use and is not suitable for commercial purposes.

Care

Do not use abrasive or caustic cleaning agents or hard brushes. Clean surfaces with a slightly damp cloth and wipe dry.

Unpacking and Disposal

Carefully remove all packaging material and dispose of it sorted by material type. Be careful not to accidentally discard assembly materials.

Parts List

Tools Required

The following tools may be needed for assembly:

• Screwdriver (Phillips head)
• Possibly an electric screwdriver (use with caution on the lowest torque setting)
• Work gloves

Assembly Steps

Step 1

Attach the main frame components. Connect the vertical and horizontal frame pieces (parts 1, D, G) using screws (S1). Ensure holes are properly aligned.

Step 2

Insert the connecting rods (part 2) into the pre-drilled holes of the frame.

Step 3

Secure the frame by inserting screws (S2) through the aligned holes.

Step 4

Insert the horizontal rods (part 2) into the frame. Turn them hand-tight only. If holes are misaligned, slightly loosen the rods. They will stabilize further in later steps.

Step 5

Attach the bottom panels (part 1) to the frame using screws (S2).

Step 6

Insert the drawer/door panels (part 4) into the frame. They should click into place.

Step 7

Attach internal supports or back panels using screws (H) and clips (S4). The diagram shows a specific sequence for inserting the clips.

Step 8

Insert the remaining drawer/door panels (part 4) into the frame. They should click into place.

Step 9

Attach the drawer runner mechanisms (part A) to the drawer panels (part 5a) using screws (S5) and pins (J).

Step 10

Attach the drawer runner mechanisms (part B) to the other drawer panels (part 5b) using screws (S5) and pins (J).

Step 11

Flip over panel 6 so that it lies on its other side. Attach it to the runner mechanism (part A) using screws (S5) and pins (J).

Step 12

Flip over panel 6 so that it lies on its other side. Attach it to the runner mechanism (part B) using screws (S5) and pins (J).

Step 13

Insert the assembled drawer units (parts 5a/6 and 5b/6) into the main frame. They should click into place.

Step 14

Attach the top panel (part 3) to the frame using screws (E1, E2).

Step 15

Attach the hinges (part 3) to the doors/drawers. Be careful when pulling out the hinge mechanism to avoid pinching fingers. Use screws (S6).

Step 16

Attach the drawer slides/runners to the main frame. Adjust the feet (step 1) for stability. Attach the runner components (part C) using screws.

Step 17

Secure the drawer slides/runners to the frame using screws (F, C, S3).

Step 18

Attach the doors/drawers to the frame by connecting them to the mounted slides.

Missing or Defective Parts

If a part is missing or defective, please refer to the service information at the end of this manual.

Service Information

For product information, accessories, or replacement parts orders, or if you have questions about service, please contact our customer service. Please provide the article number and the replacement part order number.

Customer Service Contact (General): service@tchibo.de

Specific Contacts (as per PDF):

• Germany: 040 60 02 79 00, www.tchibo.de/service
• Austria: 0800 400 235, www.tchibo.at/service
• Switzerland: 043 88 33 099, www.tchibo.ch/service
• Czech Republic: 800 900 826, www.tchibo.cz/faq
• Poland: 801 080 016, www.tchibo.pl/pomoc-i-uslugi
• Slovakia: 0800 212 313, www.tchibo.sk/faq
• Hungary: 06-80-021-375, www.tchibo.hu/GYIK
• Turkey: 444 2 826, servis@tchibo.com.tr

Article Number: 693 058