Bambu Lab Cutting Module Quick Start Guide
Follow this guide to complete the installation of the Cutting Module.
Getting Started & Resources
Scan the QR codes or visit the links below for detailed tutorials and resources.
- Unboxing Guide: Get detailed instructions for unboxing, installation, setup, and first use. Visit: bambulab.com/support/unboxing
- Download Bambu Suite: Download Bambu Suite to remotely control your printer and monitor tasks from your computer. Visit: bambulab.cn/download
- Download Free Models: Visit the MakerWorld community to download free models and connect with creators. Visit: makerworld.com.cn
- Seek Help: Visit the Help Center, contact technical support, and find more tutorials. Visit: bambulab.cn/support
Safety Guidelines
Please read the following safety guidelines carefully to ensure safe and correct use of the Cutting Module.
General Safety
- Keep your workspace clean and ensure the stability of tables and shelves where the device is placed.
- Always inspect the device for any damage before use. Stop using it immediately if damaged.
- Do not disassemble or modify the device without guidance from official after-sales support.
- The Cutting Module operates within a temperature range of 0°C to 30°C and stores between -10°C to +40°C. Avoid operating or storing the module outside these temperature ranges or in strong magnetic fields to prevent damage.
Cutting Safety
- Do not use the Cutting Module if it is not installed correctly, the locking mechanism is not engaged, or the detection structure is not in place.
- Do not hold materials by hand during cutting.
- If the Cutting Module becomes stuck or obstructed, immediately cut off the printer's power. Wait for all moving parts to stop before disconnecting the module's cable. Only then should you handle the module and material.
- When removing the blade from the blade holder, first use the included rubber protective cover to cover the blade, then carefully remove it to avoid injury. Visit the official Wiki for detailed instructions.
- After removing the blade, ensure the rubber protective cover is fully secured over the blade and store it in a location inaccessible to children to prevent injury.
- Before starting a cut, ensure the material is properly secured to prevent it from coming loose during cutting, which could damage the equipment or cause personal injury.
- When removing material, be mindful of the blade's position to avoid injury.
Component Introduction
Cutting Module Components
The Cutting Module consists of the following parts:
- Connection Cable: Connects the module to the printer.
- Tool Head Mount: The main body of the module that attaches to the printer's tool head.
- Quick-Release Latch: Lever for securely attaching and detaching the module.
- Status Indicator Light: Shows the operational status of the module.
- Blade Holder: Holds the cutting blade.
- Blade: The cutting tool itself.
- Unlock/Lock Mechanism: Visual representation of the latch operation.
Additionally, the module can be fitted with a Pen Module:
- Pen Holder: Secures the pen.
- Pen Lock: Tightens to hold the pen in place.
- Pen Adapter: Connects the pen to the module.
Printer Components
Familiarize yourself with the relevant printer components:
- Camera: Used for monitoring prints. An optional privacy cover is available.
- Heat Bed: The surface where prints are built.
- Laser Protective Window: Protects users from laser light.
- Top-View Camera: Provides an overhead view of the printing process.
- Safety Key: A safety feature for the printer.
- Auto Exhaust Grille & Cavity Exhaust Fan: Manages ventilation.
- Power Socket: Where the printer is connected to power.
Accessory List
The Cutting Module package includes:
- Cutting Module
- Cutting Mat (pre-installed with high-tack and low-tack adhesive sheets)
- Pen Module
- 45° Fine Point Blade and Protective Cover
- Hook Tool
- Pen (Black)
- Pen (Red)
- Consumables: Greeting Card (105 x 148 mm), Black Matte Heat Transfer Vinyl (300 x 300 mm)
Auxiliary Printing Tools
Enhance your cutting experience with these printable tools. Download them from makerworld.com.cn/zh/@BambuLab:
- Hook Tool Handle: For removing waste material after cutting.
- Scraper Handle: For removing material from the cutting mat.
- Roller: For flattening materials to ensure cutting accuracy.
Installation Guide
Step 1: Lower Heat Bed Height
Description: The diagram shows the printer's heat bed lowering downwards inside the printer chamber.
Instruction: Lower the heat bed height on the printer's screen. This creates sufficient space and prevents the cutting blade from damaging the cutting mat.
Step 2: Install Cutting Mat
Description: The diagram shows the print plate being removed from the heat bed. Then, the cutting mat is placed onto the heat bed, with two corners aligning with built-in limit blocks on the heat bed.
Instruction: Remove the print plate. Place the cutting mat onto the heat bed, ensuring the two corners align with the heat bed's limit blocks. Retain the protective film from both sides of the mat. When not using the cutting function, reapply the protective film to the mat to prevent dust accumulation and maintain its adhesion.
Step 3: Install Cutting Module
Description: The diagram shows the user pressing the top corners of the cutting module's front cover, then pulling the cover off.
Instruction: Press the top two corners of the front cover and remove it.
Step 4: Install Cutting Module
Description: The diagram shows the quick-release latch being moved to the unlocked position. The cutting module is then aligned with the tool head's guide slot and slid downwards until fully seated. A "Click!" sound is indicated.
Instruction: Adjust the quick-release latch to the unlocked state. Align the cutting module with the tool head's guide slot and slide the module in from top to bottom until it is fully seated.
Step 5: Install Cutting Module
Description: The diagram shows the "Click!" indicator on the module aligning with a scale line on the tool head. The quick-release latch is then pushed down to lock.
Instruction: Ensure the cutting module's "Click!" indicator aligns with the tool head's scale line, then push down to lock the quick-release latch.
Step 6: Install Cutting Module
Description: The diagram shows a dust cover being opened on the tool head's expansion interface, and the connection cable being inserted into the port.
Instruction: Open the dust cover at the tool head's expansion interface and insert the connection cable.
Step 7: Install Cutting Module
Description: The diagram shows the protective cover being removed from the blade holder. A warning about the sharp blade is displayed.
Instruction: Remove the protective cover from the blade holder. Caution: The blade is extremely sharp. Handle with care to avoid injury! It is recommended to save this protective cover and use it to cover the entire blade holder when not in use.
Using the Pen Function
Description: The diagram shows the cutting module with the pen module attached, ready for drawing.
Instruction: To use the drawing function, replace the cutting module's blade holder with the pen module.
Installing the Pen Module
Description: The diagram shows the height adjustment block being removed from the pen adapter and reattached to the bottom of the adapter.
Instruction: Remove the height adjustment block from the pen adapter and install it at the bottom of the adapter.
Installing the Pen Module
Description: The diagram shows the pen lock being loosened, the pen inserted fully, and the lock being tightened.
Instruction: Counter-clockwise loosen the pen lock. Insert the pen all the way in, then clockwise tighten the lock.
Installing the Pen Module
Description: The diagram shows the blade holder being gripped by its circular edge and pulled downwards to remove it from the tool head. A warning about the sharp blade is displayed.
Instruction: Grip the circular edge of the blade holder and pull it downwards to remove it. Caution: The blade is extremely sharp. Handle with care to avoid injury!
Installing the Pen Module
Description: The diagram shows the pen being inserted into the cutting module after the height adjustment block was removed.
Instruction: With the pen height adjustment block removed, insert the pen into the cutting module until it is fully seated.
Initial Calibration and Usage
After installing the Cutting Module for the first time, calibration is required for normal operation. Follow the on-screen prompts for the calibration process. For more detailed tutorials on calibration and usage, please refer to the Wiki page:
Regular Maintenance
Regular maintenance is essential to extend the lifespan and maintain the optimal working condition of the Cutting Module.
Tool Head Mount
Periodically check if the tool head mount is properly installed. Ensure the quick-release latch is locked and the module does not wobble. If it wobbles, tighten the screws of the quick-release latch.
Blade Holder
Periodically check for debris near the blade holder. If found, unscrew the end cap and clean the debris to prevent accumulation that may hinder blade rotation.
Consumables
- Cutting Mat: Regularly check the mat's adhesion and replace it as needed to ensure proper material fixation.
- Blade: The blade tip will wear down over time, reducing cutting quality. Replace the blade regularly to maintain cutting quality.
- Material: Different materials can affect blade lifespan. Consult the official Wiki for more information.
For more maintenance details, visit:
Technical Specifications
| Parameter Item | Parameter |
|---|---|
| Cutting Area | 300*285 mm² |
| Drawing Area | 300*255 mm² |
| Supported Pen Diameter | 10.5 mm-12.5 mm |
| Mat Type | Low-tack and High-tack Cutting Mat |
| Blade Type | 45° *0.35 mm |
| Cutting Force Range | 50 gf-600 gf |
| Max Cutting Thickness | 0.5 mm |
| Pen Recognition | Supported |
| Mat Detection | Supported |
| Supported Image Types | Bitmap and Vector |
| Supported Material Types | Paper, PVC, Vinyl, Leather, etc. |
Technical Support
If you require assistance, please contact Bambu Lab using one of the following methods:
Method 1: Contact online technical support via Bambu Handy (available 9:00 - 21:00, excluding public holidays).
Method 2: Submit a ticket in the Help Center within Bambu Handy.
You can also visit the Bambu Lab Official Wiki for more tutorials on machine usage and maintenance:
