Bambu Lab Cutting Module Quick Start Guide

This guide provides instructions for the removal and attachment of the cutting module.

Getting Started

Installation Guide

Scan the QR code on the left for details or access the link below:

bambulab.com/support/unboxing

Download Bambu Suite

Scan the QR code on the left to download Bambu Suite:

bambulab.com/download

Enjoy Your First Print on MakerWorld

Scan the QR code on the left to explore fun models from the community:

makerworld.com

In Case of Trouble

Scan the QR code on the left to access knowledge resources or contact the support team:

bambulab.com/support

Safety Precautions

To use this product safely, please review the following important precautions:

General Precautions

Ensure you have sufficient workspace before using the product.
Before use, visually inspect the product for any scratches or damage.
Do not disassemble or modify the product unless you have received guidance from the Bambu Lab support team.
The product's operating temperature range is 0-30°C, and the storage temperature range is -10-40°C. Please avoid using it outside these specified temperature ranges.

Cutting Module Safety Precautions

Always ensure the cutter is correctly attached and locked.
Do not use the product as a handheld tool.
If the cutter is difficult to move or does not move, turn off the printer, wait for the moving parts to stop, and then remove the cutter.
When removing the cutter, use the protector. For specific instructions, please refer to the Bambu Lab Wiki.
After removing the cutter, place it in a safe location. Store it out of reach of children to prevent accidental contact.
Before using the cutter, ensure the material is properly secured.
When removing processed material, be mindful of the cutter's tip position to avoid damage.

Parts Introduction

Cutting Module Parts

Diagram of the Bambu Lab Cutting Module (SC001), showing its main body, connection cable, lock mechanism, status indicator, cutter mount, and blade. Includes detailed views of the lock states and pen connection parts. Label: "Sharp blade Handle with care".

Printer Parts Introduction

Diagrams of a 3D printer showing front/side views (Live View Camera, Privacy Cover, Heat Bed, Laser Protective Window) and back/side views (Top View Camera, Safety Key, Chamber Exhaust Fan, Power Socket). Note: Privacy cover is in the accessory box.

Package Contents

Package contents: Cutting Module, Cushion for Cutter (High-viscosity and Low-viscosity surface treated), Pen Module, Blade & Protector, Needle, Pen (Black), Pen (Red), Card Paper (105x148mm), Heat Transfer Sheet (Black) (300x300mm).

Prepare Tools in Advance

Please prepare the following tools by printing them:

Diagrams of tools: Needle Handle, Scraper Handle, Roller.

Before using the Cutting Module, please obtain these three tools from makerworld.com.cn/zh/@BambuLab.

Needle: Tool for removing waste material after cutting.
Scraper: Tool for removing cushion material.
Roller: Tool for firmly attaching material to the cushion.

Installation Steps

Lower the Heat Bed

Diagram showing the heat bed being lowered with a downward arrow.

Lower the heat bed to ensure sufficient workspace.

Place the Cushion

Diagram showing build plate removal and cushion placement on the heat bed, with a zoomed view of alignment.

Remove the build plate and place the cushion onto the heat bed, ensuring it is correctly aligned. Do not discard the cushion's protective sheet; it can be attached to the cushion when not in use to prevent dust accumulation.

Install the Cutting Module

Step 1: Remove the front cover by pressing the top sides.

Diagram: Remove front cover by pressing top sides.

Step 2: Unlock the module, slide it, and attach it to the tool head.

Diagram: Unlock module, slide, and attach to tool head. "Click!" indicates successful attachment.

Step 3: Confirm the cutting module has slid to the "Click" position and lock it.

Diagram: Confirm module is in "Click" position and lock it.

Step 4: Insert the cable into the socket behind the tool head.

Diagram: Insert cable into socket behind tool head.

Step 5: Remove the protector from the cutter mount.

Diagram: Remove protector from cutter mount.

The cutter blade is extremely sharp. Handle with care to avoid injury.

Install the Pen

When using the pen, remove the cutter mount and replace it with the pen module.

Step 1: Remove the height calibration part of the pen module and attach it to the bottom of the pen module.

Diagram: Detach and attach height calibration part to bottom of pen module.

Step 2: Loosen the locking screw, insert the pen until it touches the height calibration part, then tighten the locking screw to secure the pen.

Diagram: Loosen screw, insert pen, tighten screw to secure.

Step 3: Remove the cutter mount.

Diagram: Remove cutter mount.

The blade is very sharp, so please exercise caution during operation.

Step 4: Remove the height calibration part and insert the pen module.

Diagram: Remove height calibration part, insert pen module.

Initial Calibration and Use

After installing the cutting module for the first time, initial calibration is required. Please follow the on-screen guide to complete the initial calibration.

For more details, please refer to the link below:

wiki.bambulab.com/h2/manual/cutter-setup

Regular Maintenance

To ensure optimal print quality, always maintain the cutting module in the best possible condition.

Module Mounting Position

Check if the module is securely fixed in its designated position.
Also, verify the tightness of the lock. If it feels loose, tighten the screw slightly.

Cutter Mount

Regularly clean debris and dust from around the cutter mount.
Accumulated dust or debris can impede cutter rotation, potentially preventing cutting operations.

Consumables

Check the cushion's viscosity. If the viscosity decreases, the material may not be secured firmly. Replace the cushion in such cases.
The cutter blade may be worn. Replace it based on its condition.
Cutter wear can be accelerated depending on the material used. Always check the cutter's sharpness and determine if replacement is necessary.

For more details, please visit:

bambulab.com/support/maintenance

Technical Specifications

Item	Specification
Cutter Working Area	300*285 mm²
Pen Working Area	300*255 mm²
Pen Diameter	10.5 mm–12.5 mm
Cushion Surface Type	High-viscosity and Low-viscosity
Cutter Blade	45° *0.35 mm
Blade Pressure	50 gf–600 gf
Max Cutting Thickness	0.5 mm
Cutter/Pen Detection	Yes
Cushion Type Detection	Yes
Input Image Type	Bitmap and Vector
Material Type	Paper, PVC, Leather, some resins

Technical Support

If you require support, please use the following methods:

Method 1: Contact the Support Team via Webpage