R50C PoE Splitter Datasheet
Technical Information and Specifications
Technical Information
This guide provides essential information for setting up and installing the R50C PoE Splitter. For comprehensive details on programming, performance, troubleshooting, dimensions, and accessories, please consult the Product Manual available at www.bannerengineering.com. Search for part number 235182 to access the Product Manual. Familiarity with pertinent industry standards and practices is assumed.
Status Indicators
Power LED Indicator (Green): Solid Green = Power On, Off = Power Off
Specifications
Input Characteristics
- Voltage: 42.5 V DC to 57 V DC
- Current: 30 mA independent of powered device
- PoE Standard: Class 0 - 802.3af, 802.3at Type 1
Output Characteristics
- Voltage: 24 V DC ±10%
- Current: 450 mA average
- Power: 12.95 W
- Power Supply Type: Limited energy power supply evaluated to IEC, UL, and CSA 61010-2-201. Suitable for devices requiring a Class 2 or SELV power supply.
Supply Protection Circuitry
Protected against reverse polarity and transient voltages.
Data Rate
10/100 Mbps
Construction
- Coupling material: Nickel-plated brass
- Connector body: PVC translucent black
Connections
- (2) Integral 4-pin D-code M12 female quick-disconnect connectors
- (1) Integral 4-pin M12 female quick-disconnect connector
Environmental Rating
- IP65, IP67, IP68
- UL Type 1
Operating Conditions
- Temperature: -40 °C to +50 °C (-40 °F to +122 °F)
- Humidity: 90% at +60 °C maximum relative humidity (non-condensing)
Storage Temperature
-40 °C to +80 °C (-40 °F to +176 °F)
Vibration and Mechanical Shock
- Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 0.5 mm amplitude, 5 minutes sweep, 30 minutes dwell)
- Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half sine wave)
Product Identification
SNAP SIGNAL
Certifications
CE
Banner Engineering BV
Park Lane, Culliganlaan 2F bus 3
1831 Diegem, BELGIUM
UK CA
Turck Banner LTD
Blenheim House
Blenheim Court
Wickford, Essex SS11 8YT
GREAT BRITAIN
CULUS LISTED IND. CONT. EQ. E316212
Required Overcurrent Protection
WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations.
Overcurrent protection is required to be provided by the end product application as detailed in the supplied table. This protection can be achieved through external fusing or by using a Current Limiting, Class 2 Power Supply. Supply wiring leads smaller than 24 AWG should not be spliced.
For additional product support, visit www.bannerengineering.com.
| Supply Wiring (AWG) | Required Overcurrent Protection (A) | Supply Wiring (AWG) | Required Overcurrent Protection (A) |
|---|---|---|---|
| 20 | 5.0 | 26 | 1.0 |
| 22 | 3.0 | 28 | 0.8 |
| 24 | 2.0 | 30 | 0.5 |
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective during the warranty period upon its return to the factory. This warranty does not cover damage or liability arising from misuse, abuse, or improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING, OR TRADE USAGE.
Banner Engineering Corp. reserves the right to change, modify, or improve the design of the product without assuming any obligations or liabilities related to previously manufactured products. Misuse, abuse, improper application or installation, or use of the product for personal protection applications (when not intended for such purposes) will void the product warranty. Modifications made without prior express approval from Banner Engineering Corp. will also void product warranties. All specifications published herein are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede any provided in other languages. For the most recent documentation version, refer to www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
