Birdfy Feeder User Manual
Brand: Birdfy (by Netvue Inc.)
Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications made without explicit approval from the responsible party in compliance may result in the user being unauthorized to operate the device.
This device meets the FCC radiation exposure limits for uncontrolled environments. To ensure safe installation and operation, maintain a minimum distance of 20cm between the radiator and your body.
FCC ID: 2AO8RNI-8101
CE Statement
The information provided on the packaging is allowed to identify geographical areas within the member states where restrictions on use or requirements for authorized use exist, if applicable. The structure of the product allows it to be used in at least one member state without violating applicable requirements for the use of radio spectrum.
Manufacturer Information:
NETVUE INC.
1055 East Colorado Boulevard 5th Floor
Pasadena, CA, 91106
Contents
What's in the Box
- Roof
- Screws for mounting on wood (x3)
- Anchors
- Perch screw
- Perch
- Feeder & camera unit
- Drilling template
- Mounting bracket
- Ejector pin
- User Manual (this document)
- Quick Guide
- Black strap
- Hose clips (small) (x2)
- Hose clips (large) (x2)
- Screws for mounting on concrete (x3)
- Tripod adapter
- Solar panel + installation package (Note: Not included in "no-solar" bundles)
- Type-C charging cable
Inserting MicroSD Card
The Birdfy Feeder comes with a built-in card slot which supports Class 10 microSD cards with capacities of up to 128GB.
- Rotate the camera downwards.
- Open the silicone cover and insert the microSD card. Make sure it is properly positioned with the label facing upward.
- Put back the silicone cover.
Camera Charging
The camera does not come fully charged due to safety regulations. Before using it for the first time, please charge it for 14 hours with the charging cable inside the box (DC5V / 1A).
Status light:
- Solid yellow: charging
- Solid green: fully charged
Turning the Camera On & Off
To power on or off: Long press the power button located at the top of the camera.
Pre-Installation Notes
- Keep Birdfy Feeder and all accessories out of the reach of children and pets.
- Make sure the camera is fully charged (DC5V / 1A).
- Working temperature: -10°C to 50°C (14°F to 122°F)
- Working relative humidity: 0-95%
- Please avoid exposing the camera lens to direct sunlight.
- The camera has an IP65 waterproof rating, which allows it to function properly in rainy or snowy conditions. However, it should not be submerged in water.
Notes:
- Birdfy Feeder only works with 2.4GHz Wi-Fi.
- Strong light may interfere with the device's ability to scan QR codes.
- Avoid placing the device behind furniture or near a microwave oven. Please try to keep it in the range of your Wi-Fi signal.
AI Bird Identification
If you bought the Birdfy Feeder AI, this feature is included and activated automatically, without any additional cost.
If you have the Birdfy Feeder Lite, you need to subscribe to access this feature.
With AI Bird Identification, you can find out in real-time which bird species are visiting your feeder.
Support & More Information
Learn more on www.birdfy.com.
Contact us at:
- Email: support@birdfy.com
- In-App Chat
- Phone: 1(886)749-0567 (Mon-Fri, 9am-5pm, PST)
Follow us on social media: @birdfy by netvue
© Netvue Inc.
