Best Choice Products Ride-On Truck with Remote

Important Safety Information

This vehicle must be assembled by an adult who has read and understood the instructions in this manual. Keep packaging and bags away from children. Always use common sense and safe practices. This product may contain chemicals known to the state of California to cause cancer or birth defects or other reproductive harm.

Note: For best performance, use this vehicle only on flat and hard surfaces.

Age Range: 3 to 8 years old

Weight Capacity: 65 lbs.

Safety Hazards:

• Contains small parts; keep children away during assembly. Remove all packaging material.
• Never open the battery. Batteries contain lead and lead compounds (acids) that are toxic and corrosive.
• Keep limbs, hair, and clothing away from moving parts. Always wear shoes.
• This vehicle has no brakes. Do not leave a child unattended during operation.
• Avoid operating near streets, motor vehicles, steps, bodies of water, slopes, wet areas, flammable vapors, or in the dark.
• Avoid unsafe conditions like snow, rain, loose dirt, mud, sand, or gravel, which could cause tipping or damage.
• Do not operate in an unsafe manner, such as pulling with another vehicle, allowing more than one rider, pushing the user, or traveling at an unsafe speed.

Battery Warnings:

• Use only the supplied 12V rechargeable battery and charger. Using other types may cause fire or explosion.
• Do not use the supplied battery and charger for any other product.
• Charge the battery in a well-ventilated area away from heat or flammable materials.
• Avoid direct contact between battery terminals. Pick up the battery by its case or handles, not the wires.
• Keep liquids away from the battery. If battery leakage occurs, flush affected skin with cool water for 15 minutes and seek medical attention. Do not induce vomiting if swallowed.
• Never open the battery.
• Do not tamper with or modify the electric circuit system. Keep charger housing closed.

Warnings

Adult supervision is required. Never use on roadways, near motor vehicles, or near inclines, steps, or bodies of water. Always wear shoes. Never allow more than one rider. Never leave a child unattended. Always sit in the seat. Keep hands, hair, and clothes away from moving parts. Not for children under 3 years old. Only drive on level ground. Do not drive on loose dirt, mud, sand, fine gravel, or wet surfaces.

California Proposition 65

WARNING: Battery posts, terminals, and related accessories can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm, and are toxic and corrosive. Wash hands after handling. For more information go to www.P65Warnings.ca.gov.

Caring for Your Ride-On

• Park the vehicle indoors or cover it with a tarp to protect it from wet weather.
• Do not leave the vehicle in the sun for long periods to prevent fading. Store in shade or cover with a tarp.
• Do not wash the vehicle with a hose.
• Do not wash the vehicle with soap.

Specifications

Tools Required

• Phillips Screwdriver
• 2 Plastic Wrench (Provided)

Hardware

• 1: M4 x 12mm Screw (10 PCS)
• 2: M3 x 12mm Screw (2 PCS)
• 3: M4 x 16mm Screw (6 PCS)
• 4: Spring (2 PCS)

Parts - Box A

• A: Rear Axle (1 PC)
• D: Hub Cap (4 PCS)
• E: Frame (2 PC)
• F: Bar Light (1 PC)
• G: Hood Latch (1 SET (SPARE))
• H: Windshield (1 PC)
• I: Side Mirror (2 PCS)
• J: Seat (1 PC)
• L: Steering Wheel (1 PC)
• M: Front Reflector (2 PCS)
• N: Remote Control (1 PC)
• O: Charger (1 PC)
• Q: Bumper (1 PC)

Parts - Box B

• B: Rear Wheel (2 PCS)
• C: Front Wheel (2 PCS)
• K: Front Axle (1 PC)
• P: Axle Frame (1 PC)

Product Assembly

1. Step 1: Flip the vehicle over onto a level surface. Remove the brackets holding the rear axle (Part A), then remove the axle. Remove the nuts and washers from the rear axle.
2. Step 2: Remove packaging from gear boxes and lift the rear shocks. Align the gear boxes with the shocks, then slide the rear axle (Part A) through.
3. Step 3: Slide a rear wheel (Part B) onto the axle and replace a nut and washer to secure it. Repeat on the other side. Snap a hub cap (Part D) onto each wheel. Use the provided plastic wrench to attach the nuts.
4. Step 4: Attach the bumper (Part Q) with six screws (Part 3).
5. Step 5: Remove two nuts from the bottom of the front axle (Part K). Slide two springs (Part 4) onto the axle frame (Part P). Attach the springs and axle frame to the front axle by replacing the two nuts.
6. Step 6: Remove the nut and washer from the steering column. Slide the front axle assembly onto the steering column and secure it by replacing the nut and washer. Place the front axle assembly into the designated slots and secure with eight screws (Part 1), four on each side.
7. Step 7: Remove two nuts and washers from the front axle. Slide a front wheel (Part C) onto the axle and replace a nut and washer to secure it. Repeat on the other side. Snap a hub cap (Part D) onto each wheel. Use the provided plastic wrench to attach the nuts.
8. Step 8: Connect the steering wheel (Part L) to the corresponding connector in the steering mount, then snap the steering wheel into place. (To remove, compress buttons on the sides of the steering wheel.)
9. Step 9: Insert the two frame pieces (Part E) into the designated holes on the rear of the vehicle.
10. Step 10: Slide the bar light (Part F) into the holes on the frame pieces and secure with two screws (Part 2).
11. Step 11: Snap on the windshield (Part H).
12. Step 12: Snap on two side mirrors (Part I).
13. Step 13: Attach the seat (Part J) with two screws (Part 1).
14. Step 14: Slide the front reflectors (Part M) onto the front of the vehicle; they will snap into place.
15. Step 15: Under the hood, connect the orange connector from the battery to the control module.

Dashboard Diagram

Controls:

• Power Switch
• Light Switch
• Pedal: Push down to drive forward/reverse. Release to slow down and stop.
• Forward: Drive Forward
• Park: Park Vehicle (Pedal is disabled)
• Reverse: Drive in Reverse

Media Player

• Back/Volume-: Short press for previous song/station; long press to decrease volume.
• Play/Pause/Seek: Play/pause music; seek radio stations.
• Forward/Volume+: Short press for next song/station; long press to increase volume.
• Mode: Toggle between music and FM radio.

Bluetooth

1. Place your audio device near the media player and power on the car.
2. Press 'Mode' on the media player until you hear "Bluetooth device is ready to pair."
3. On your audio device, locate Bluetooth settings and select "Best Choice Products Ride On."
4. When the device says "Your Bluetooth device is connected successfully," select your desired song.

Remote Control Diagram

Controls:

• Forward
• Emergency Brake (P)
• Reverse (S)
• Speed Control
• Frequency Key (Up Arrow)
• Turn Left (Left Arrow)
• Turn Right (Right Arrow)
• High-Speed LED
• Medium-Speed LED
• Low-Speed LED

Operation:

• Insert 2 AAA batteries into the remote control.
• The indicator light turns off after 10 seconds of non-operation to enter power-saving mode.

Linking the remote control:

1. Press and hold the frequency key for 2-4 seconds. The low speed LED lights will flash.
2. Turn the vehicle on. The low speed LED lights will stop flashing and remain on to indicate a successful link.
3. If the low speed LED lights continue to flash (unsuccessful link), remove the battery from the remote and repeat steps 1 and 2.

Charging Instructions and Warnings

• The charging socket is located under the dashboard on the left side. Insert one end of the charger (Part O) into the socket and plug the other end into a wall outlet.
• Charge the battery for at least 12 hours before initial use.
• Average charging time is 8-12 hours. Do not charge for more than 20 hours. Failure to charge properly may damage the battery and void the warranty.
• Do not allow the battery to drain completely.
• Check the battery, charger, and supply cord for wear and damage before charging. Do not charge if damaged.
• Only an adult who has read and understood the safety warnings should handle, charge, and recharge the battery.
• Charging Steps:
  1. Open the hood and disconnect the orange connector from the battery to the control module.
  2. Insert the charger (Part O) into the battery charging socket and plug the other end into a wall outlet.
  3. Charge the battery for 8-10 hours, then disconnect.
  4. Remove the charger and reconnect the battery to the control module.

Warnings Regarding Batteries:

• Do not mix battery types (alkaline, carbon zinc, nickel hydride).
• Do not mix old and new batteries.
• Do not charge non-rechargeable batteries.
• Charge rechargeable batteries only under adult supervision.
• Remove exhausted batteries.
• Do not short-circuit supply terminals.
• Keep batteries away from heat sources.
• Do not hit batteries against hard objects.
• Do not submerge batteries in water.
• Insert batteries with the correct polarity.

Troubleshooting

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This product may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Responsible party (contact for FCC matters only):
Quality Control Dept.
15101 Red Hill Ave.
Tustin, CA 92780

Help Center

Question about your product? Visit us at: help.bestchoiceproducts.com

Services:

• Chat Support
• Product Inquiry
• Orders FAQ
• Product Assembly
• Returns & Refunds

Product Warranty Information

All items can be returned for any reason within 60 days of receipt for a full refund, provided they are in their original packaging with all accessories. Refunds will be issued to the original payment method. No restocking fees apply.

An RA (Return Authorization) number, obtained from a Best Choice Products Customer Service Representative, is required for all returns. Items received without an RA may experience processing delays or be rejected. Refunds or replacements are processed within 5 business days of receipt.

Return shipping costs are the customer's responsibility unless the return is due to an error by Best Choice Products, in which case a pre-paid shipping label will be provided. Customers are responsible for providing return shipping boxes.

Photos may be required for some returns to verify item condition prior to return. Items are considered undamaged only after they are received and verified by Best Choice Products.

Warning

Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this product.