936 Instruction v1

• Google Docs
• Google Drive
• Download [pdf]



File Info : application/pdf, 20 Pages, 5.34MB

Document Document

INSTRUCTION MANUAL

12V Licensed Kids Ride-On Chevy Silverado Truck

Ver. 1

SKY7411 + SKY7412 + SKY7413 + SKY7414 + SKY7415

To reduce the risk of injury, adult supervision is required. Never use on roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one rider.
FOR: 3-6 YEARS OLD & UP TO 66 LBS
CHOKING HAZARD - Small parts. Not for children under 3 years old.
ADULT ASSEMBLY REQUIRED
bestchoiceproducts.com

Charge for 12 hrs before initial use. After initial charge, follow the normal
recommended charging time.
bestchoiceproducts.com

SAFETY Please retain these instructions for future reference.
This vehicle must be assembled by an adult who has read and understood the instructions in this manual. Keep the packaging and bags away from children and dispose of all packaging before use. Always use common sense and safe practices when operating this vehicle. This product contains or emits chemicals known in the state of California to cause cancer or birth defects or other reproductive harm.
NOTE: For best performance, only use this vehicle on flat and hard surfaces. AGE RANGE: 3 to 6 years old WEIGHT CAPACITY: 66 lbs. The following safety hazards may result in serious injury or death:
· This product contains small parts. Keep children away during assembly. Make sure to remove all packaging material and parts from underneath the vehicle body.
· Never open the battery. Batteries contain lead and lead compounds (acids) that are toxic, corrosive, and known to the state of California to cause cancer and reproductive harm.
· Limbs, hair, and clothing can get caught in moving parts. Always wear shoes, keep limbs away from moving parts, and do not wear loose clothing while operating this vehicle.
· This vehicle does not have brakes or braking capability. Do not leave a child unattended during operation. Do not use this in a location that may require braking capability, as this could result in loss of control, which may cause serious injury or death.
· Use of this vehicle near streets, motor vehicles, steps, bodies of water, sloped surfaces, hills, wet areas, flammable vapors, in alleys, at night, or in the dark could result in an unexpected accident.
· Use of this vehicle in unsafe conditions such as snow, rain, loose dirt, mud, sand, or gravel may result in an unexpected accident such as tipping over and could damage the electrical system or battery.
· Do not operate this vehicle in an unsafe manner. Examples include but are not limited to:
- Pulling the vehicle with another vehicle or similar device - Allowing more than one rider - Pushing the user - Traveling at an unsafe speed
· This product is intended for residential use only.
BATTERY WARNINGS
The following safety hazards may result in serious injury or death:
· Use of a battery or charger other than the supplied rechargeable battery and charger may cause a fire or explosion. Only use the supplied battery and charger. Never use the supplied rechargeable battery and charger with another product.
· Damage to the battery may occur if it is allowed to drain completely. Do not allow the battery to drain completely.
· Explosive gases are created during charging. Charge the battery in a well-ventilated area. Do not charge the battery near heat or flammable materials.
· Contact between the positive and negative terminals may result in fire or explosion. Avoid direct contact between the terminals. Picking up the battery by the wires or charger can cause damage to the battery and may result in a fire. Always pick up the battery by its case or handles.
· Liquids on the battery may cause fire or electric shock. Always keep all liquids away from the battery and keep the battery dry. Contact or exposure to battery leakage (lead acid) may cause serious injury. If contact or exposure occurs immediately call your physician. If the chemical is on the skin or in the eyes, flush with cool water for 15 minutes. If the chemical was swallowed, immediately give the person water or milk. Do not give water or milk if the patient is vomiting or has a decreased level of alertness. Do not induce vomiting.
· Battery posts, terminals, and related accessories contain lead and lead compounds (acid) ­ chemicals known to the State of California to cause cancer, reproductive harm, and are toxic and corrosive. Never open the battery.
· Tampering or modifying the electric circuit system may cause a shock, fire or explosion and permanently damage the system. Exposed wiring and circuitry in the charger may cause electric shock. Always keep the charger housing closed.
4 |

USER WARNINGS
To reduce the risk of injury, adult supervision is required. Never use on roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one rider. CHOKING HAZARD ­ Small parts. Not for children under 3 years old. · Never leave a child unattended. · Always sit in the seat when using this vehicle. · Keep your hands, hair, and clothes away from moving parts. · Children under 3 years of age cannot use the vehicle. · Only drive on level ground. · Do not drive the vehicle into loose dirt, mud, sand, fine gravel, or on wet surfaces.
SPECIFICATIONS

Overall Dimensions

42.9"(L) x 28.4"(W) x 25.2"(H)

Weight Weight Capacity
Age Range Max Speed Initial Charge Time

39 lbs.
66 lbs.
3 ­ 6 years old Low - 1.2 mph. High - 2.5 mph.
12 hours

Charging Time Run Time

8 ­ 12 hours 1 ­ 2 hours

Battery Type Electric Motor Charger Input / Charger Output Product Materials

12v 4.5 Ah
DC 12V Input: 100V~240V AC / Output: DC 12V  0.5A Polypropylene and Metal

| 5

TOOLS REQUIRED

+ AA -

2 AA BATTERIES (FOR STEERING WHEEL)

+ AAA -

PHILLIPS SCREWDRIVER

PLASTIC WRENCH (PROVIDED)

2 AAA BATTERIES (FOR REMOTE)

LBS

66 LBS

2 PERSON

CAPACITY ASSEMBLY

UP TO 45 MIN. ASSEMBLY

HARDWARE NOTE: Some hardware will come pre-attached to assembly parts

1 M4 x 16mm SELF-TAPPING SCREW

2 M3 x 10mm SELF-TAPPING SCREW

4 PCS
PARTS
A STEERING WHEEL

14 PCS
B SEAT

C BACKREST

1 PC
D REMOTE CONTROL

1 PC
E WINDSHIELD

1 PC
F WHEEL COVER

1 PC

1 PC

4 PCS

6 |

PARTS
G WHEEL

H SIDE MIRRORS (L/R)

I SIDE WINDOW (L/R)

4 PCS
J 12V CHARGER

1 SET

1 SET

1 PC

PRODUCT ASSEMBLY

1

Place the vehicle body on a flat, covered surface to prevent scratches, then locate taillights at the back of the vehicle and secure with four part 2 screws, two screws per light.

Locate the rear axle and carefully remove the zip ties securing it in place. Remove the

preassembled hardware, two nuts and two washers, then set aside.

Front

[1]

[2]

[3]

[1] [2]

2 x4
| 7

PRODUCT ASSEMBLY

2

Locate the rear drive motors, then carefully thread them over each side of the rear axle.

[4]

[8] Z

Z [8] [4]

Front

3

Locate the front axle and remove the preassembled hardware, two nuts and two washers, then set aside.

[6] [5]

[6] [5]

Front

8 |

PRODUCT ASSEMBLY

4

Attach two part G wheels to each axle, then secure with the previously removed hardware, place the washers first, then secure the nuts. Attach one part F wheel cover to each part G wheel.

Flip the vehicle body so all four wheels touch the ground.

G
[6] [5]
F

G
[6] [5]
F

Front

[2]

G

[1]

F

G

[2]

[1]

F

| 9

PRODUCT ASSEMBLY

5

Use a Philips screwdriver to open the battery access on the part A steering wheel, then install two AA batteries. Replace the battery cover and secure the screw.

A

+

-

+

-

6

Locate and remove the bolt on the side of the part A steering wheel's shaft.

Place the part A steering wheel over the steering yoke, then replace the bolt to secure.

A A

[ 7]
10 |

PRODUCT ASSEMBLY

7

Locate one part I side window and attach it to the inside of the car body with five part 2 screws. Repeat to attach a second part I window.

I x2

8

Insert the part E windshield into the front of the vehicle body, then locate the inset holes on the doors, and insert the part H side mirrors, push until secure.

E

H

H

| 11

PRODUCT ASSEMBLY

9

Place the part B seat onto its designated space on the vehicle body, then secure with two part 1 screws.

B

1 x2

10 Press part C backrest into its designated space on the vehicle body, then secure with two part 1 screws.

C

1 x2

12 |

REMOTE CONTROL DIAGRAM
· Remote control operation will OVERIDE manual operation; the pedal will not work when operating the remote control.
· After a period of non-operation, the remote will go into power-saving mode.
Forward Turn left

+

-

+

-

Stop

Turn right

Reverse LED Indicator speed
· Use a Philips screwdriver to remove the battery cover on the back of the part D remote control. Install two AAA batteries then replace the battery cover.
LINKING THE REMOTE CONTROL: (Install batteries before linking) 1. Turn the vehicle o . 2. Install 2 AAA batteries into the remote control and the indicator lights will flash. 3. Turn the vehicle on, 2 indicator lights on the remote will turn solid, indicating a successful link. 4. If the indicator lights continue to flash (indicating an unsuccessful link), remove and reinsert batteries
and repeat steps 1 to 3.
DASHBOARD DIAGRAM

1

TUNE

U

MP3

FM MODE

START

STO P

V-

V+

High Low

3

2

4

Push down on the pedal to drive forward/reverse.
Release the pedal to slow down and stop.
1. Horn I 2. Horn II 3. Control Board 4. Foot Pedal

| 13

CONTROL BOARD DIAGRAM
11 12 13

1

TUNE

MP3

4

2

FM

5

START

STOP

V-

V+

MODE

High

3

Low

6

7 8 9 10
1. TUNE: FM radio search, press to find FM radio channels. 2. FM: Press to enter FM Radio Mode. 3. MODE: Press to toggle between start sound, the media player, and the aux input. 4. FORWARD: Press to make the car move forward when the foot pedal is pressed. 5. REVERSE: Press to make the car move backward when the foot pedal is pressed. 6. HIGH/LOW SPEED: Press to alternate between preset "Low" and "High" speeds. 7. PREVIOUS/VOLUME DOWN: Short press to play the previous selection/channel. Long press to lower
the speaker volume. 8. LIGHT SWITCH: Press to power on lights. Press again to power o lights. 9. NEXT/VOLUME UP: Short press to skip to the next selection/channel. Long press to raise the
speaker volume. 10. START/STOP: Long press to turn the vehicle power on or o . Short press when the music or radio is
on to turn them o ; short press again to restart the music or radio. 11. MEDIA PLAYER PORT: Insert flash drive or additional media device to play music. Supports only
MP3 music files. 12. VOLTAGE DISPLAY SCREEN: Displays battery status to indicate charging requirements. 13. AUX CONNECTOR: Connect with other removable device to play supported audio files.
BLUETOOTH
· Place your desired audio device near the media player and power the car on. · Press MODE on the media player and wait until you hear "Bluetooth device is ready to pair." · On your desired audio device, locate the Bluetooth settings and select the device named "Best Choice
Products Ride On." · When the device states "Your Bluetooth device is connected successfully," then select the desired song.
14 |

CONNECTING THE BATTERY
1

2

3

[1] [2]
1. Locate and open the charging hole cover, beneath the seat. 2. Insert the power supply into the receiver as shown. 3. Close the charging hole cover.
WARNING
RISK OF FIRE. Do not bypass fuse. This may overload and damage the electrical system. Replace only with original size and type.
RECOVERABLE FUSE INSTRUCTIONS Resettable fuse: When the current exceeds a certain rating, the recoverable fuse will automatically cut o the power supply for 5-60 seconds, then the current will be resupplied.

| 15

CHARGING INSTRUCTIONS
1

2

3

J

45

6

1. Charging connector is located under the seat. 2. Unplug the power supply from the receiver then insert the supply into the part J charger and plug the
other end into a wall outlet. 3. Charge the battery 12 hours before initial use. 4. When fully charged, unplug part J charger from the wall outlet, then remove the charger from the
power supply. 5. Reconnect the power supply to the receiver, then place the connector back under the seat.
16 |

CHARGING NOTICE
· On average, you will need to charge the battery between 8 and 12 hours. Do not charge the battery for more than 20 hours. Failure to charge the battery as directed could cause permanent damage to the battery and void the warranty.
· Damage to the battery may occur if it is allowed to drain completely. Do not allow the battery to drain completely.
· Check the battery and charger (supply cord, connector) for wear and damage before charging. Do not charge the battery if damage has occurred.
· Only an adult who has read and understood the safety warnings should handle, charge and recharge the battery.

CARING FOR YOUR RIDE-ON
· Park the vehicle indoors or cover it with a tarp to protect it from wet weather. · Do not leave the vehicle in the sun for long periods of time or fading may occur. Store in shade or cover
with tarp. · Do not wash the vehicle with a hose. · Do not wash the vehicle with soap. · Charge battery at least once a month to prolong the life of the battery.

TROUBLESHOOTING

Problem Vehicle does not move
Battery does not recharge Battery does not last

Reason Low battery Electrical protection Switch not in the correct position Battery connectors disconnected Battery connectors disconnected Charger not connected to socket or outlet

Solution Fully charge the battery Stop use for several minutes and restart Completely press in switches Plug in battery connectors Plug in battery connectors
Completely plug in the charger

Battery does not have a full charge Fully charge the battery

Battery is warm and makes Normal a slight noise while charging

Slow speed
Vehicles shakes while driving Vehicle is silent

Low battery Overloaded vehicle Uneven or sloped road
Loose connection to motor
Handle bars is not properly connected

Normal
Fully charge the battery Reduce the weight on the vehicle Drive on flat pavement Ensure the motor is properly connected to the battery Properly connect the steering wheel connector

| 17

WARNINGS REGARDING BATTERIES
· Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries. · Do not mix old and new batteries. · Non-rechargeable batteries should not be charged. · Rechargeable batteries should be charged under adult supervision only. · Exhausted batteries should be removed. · The supply terminals should not be short-circuited. · Do not put batteries next to or in a heat source (fire, electronic heating device, etc.). · Do not hit batteries against hard objects. · Do not submerge batteries in water. · Batteries should be inserted with the correct polarity.
CALIFORNIA PROPOSITION 65
WARNING: Battery posts, terminals, and related accessories can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm, and are toxic and corrosive. Wash hands after handling. For more information go to www.P65Warnings.ca.gov
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This product may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit di erent from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Responsible party (contact for FCC matters only): Quality Control Dept. 15101 Red Hill Ave. Tustin, CA 92780
18 |

Earn points while you shop. Join today!
Give your friends 15% o their first order! For each successful referral you'll receive 100 points.
bestchoiceproducts.com

HELP CENTER

Question about your product? We're here to help. Visit us at:
help.bestchoiceproducts.com

CHAT US!
Chat Support

Product Inquiry

Orders FAQ

Product Assembly

Returns & Refunds

PRODUCT WARRANTY INFORMATION
All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long as the item is returned in its original product packaging and all accessories from its original shipment are included. All returned items will receive a full refund back to the original payment method. All returned items will not be charged a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best Choice Products Customer Service Representative when the return request is submitted. Items received without an RA may not be accepted or may increase your return processing time. Once an item has been received by Best Choice Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer's expense. If the reason for return is a result of an error by Best Choice Products then Best Choice Products will provide a pre-paid shipping label via email. Boxes for return shipping will not be provided by Best Choice Products, and is the customer's responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items returned are not considered undamaged until they are received by Best Choice Products and verified as such. All damages to items are the customer's responsibility until the item has been received by and acknowledge by Best Choice Products as undamaged.
© 2023 Best Choice Products, Inc. All rights reserved. Distributed by Best Choice Products, Inc. Tustin, CA 92780

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.