Bottle Trap Installation Instructions

Product Information

Product Name: Bottle Trap

Product Codes: ACC186-W-CR / ACC186-W-MB / ACC186-W-BN / ACC186-W-CG / ACC186-W-GM

Installation Instructions

The inlet of this bottle trap is compatible with a 40mm waste connection. The outlet key seal of this bottle trap is designed to suit a 40mm PVC DWV socket.

1. Cut the DWV Pipe so that between 1mm to 5mm protrudes through the wall or vanity cabinet back. Ensure the pipe is cut square and deburr.
   Illustration depicts cutting a DWV pipe square and deburring it, ensuring it protrudes 1mm to 5mm from the wall or cabinet.
2. Connect Bottle trap inlet pipe (2) to the waste outlet using Sealing washer (1) and compression Nut (3). Do not fully tighten; adjustment will be needed during installation.
   Illustration shows connecting the bottle trap inlet pipe (2) to the DWV pipe using a sealing washer (1) and compression nut (3).
3. Apply plumber's grade lubricant or soapy water to one end of the Outlet pipe (10). Fit Key seal (12) onto the end of Outlet pipe (10).
   Illustration shows applying lubricant to the outlet pipe (10) and fitting the key seal (12).
4. Insert the assembled Outlet pipe (10) and Key seal (12) into DWV pipe, until Key seal's raised lip meets the DWV pipe.
   Illustration shows inserting the assembled outlet pipe (10) with key seal (12) into the DWV pipe until the seal's lip meets the pipe.
5. Loosen Compression nut (4) then adjust height of Bottle trap inlet pipe (2). Note: Ensure a minimum 1.5° fall (per AS/NZS 3500.2).
   Illustration shows loosening compression nut (4) and adjusting the height of the bottle trap inlet pipe (2), with a note about ensuring a minimum 1.5° fall.
6. Position the Bottle trap outlet towards the DWV pipe. Measure the Outlet pipe and make a mark 30mm past the face of Compression nut (3), to ensure sufficient length for sealing. Cut the Outlet pipe (10) at the mark using a pipe cutter and deburr. Slide the Wall flange (11) onto the Outlet pipe.
   Illustration depicts positioning the bottle trap outlet, marking the outlet pipe (10) 30mm past compression nut (3), cutting the pipe, and sliding the wall flange (11) onto it.
7. Disconnect Bottle trap from waste outlet. Assemble Outlet pipe (10) to Bottle trap using Tapered washer (9) and Compression nut (3). Do not fully tighten.
   Illustration shows disconnecting the bottle trap from the waste outlet and assembling the outlet pipe (10) to the bottle trap using a tapered washer (9) and compression nut (3).
8. Lubricate Key seal (9) on end of Outlet pipe, Push Key seal and Outlet pipe into DWV pipe.
   Illustration shows lubricating the key seal (9) on the outlet pipe and pushing it into the DWV pipe.
9. Re-fit Bottle trap to the waste outlet. Adjust Bottle trap position and height, then tighten all connections.
   Illustration shows refitting the bottle trap to the waste outlet, adjusting its position and height, and then tightening all connections.
10. Fill basin with water, test for correct function, and check for leaks.
    Illustration shows filling the basin with water to test for leaks and correct function, followed by an illustration with a checkmark indicating successful installation.

Care & Maintenance

Avoid using abrasive or acid based cleaning products.

To clean the bottle waste trap, unscrew the large threaded Bung (8) at the base of the bottle trap. Clean any waste from the bottle trap, clean the O-ring seal (7) and reassemble the threaded Bung (8).

Warranty

This Bottle Trap is warranted to be free from manufacturing defects for a period of:

• 1 Year replacement of parts, seals, finish and labour

This warranty does not cover against normal wear and will be voided if the product is misused or not installed in accordance with these instructions.

In the event this product is rendered obsolete and a replacement product is required, Oliveri Solutions Pty Ltd reserves the right to supply a product of equal substitution at their discretion.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be acceptable quality and the failure does not amount to a major failure.

Service

If the Bottle trap requires servicing, please contact your installer (preferably the one who installed it). If the installer is satisfied that the problem is not due to poor installation, contact Oliveri's nominated service agent for assistance on:

Ph: (08) 8348 6444

Email: warranty@oliveri.com.au

For full warranty information visit: https://oliveri.com.au/service-and-warranty

If a warranty service call finds that the product does not have a genuine manufacturing fault, our Warranty Service Agent reserves the right to pass on any call-out fee to the householder.

Technical Specifications