HYUNDAI ELECTRONICS

Statements

Federal Communication Commission Interference Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

RF Exposure: A distance of 20cm shall be maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna.

ISED Statement

Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

étiquette de conformité à la NMB-003 d'Innovation, Sciences et Développement économique Canada: CAN ICES-3 (B)/NMB-3 (B)

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet appareil et toutes les personnes.

Wi-Fi Module Specification and Operation Guideline

1. Minimum specifications on a Smart phone:

• Android 5.0 version or higher
• IOS 9.0 version or higher

2. Basic parameters for Wi-Fi module

3. Operation guideline. For reference, see simple guideline instructions below.

Note: If you registered the account and added device before, when you re-install the APP again and login, the added device will remain.

Download and Install the App

[App Icon: Smart Life] Smart Life

For Android smart phone

Method 1: Please scan the QR code [QR code for Android app download] with a browser scanner, download and install the APP.

Method 2: Open the Google "Play Store" on your smart phone and search "Smart Life", download and install the APP.

For IOS smartphone

Method 1: Please scan the QR code [QR code for iOS app download] and follow the tips to get into "AppStore", download and install the APP.

Method 2: Open the Apple "AppStore" on your smartphone and search "Smart Life", download and install the APP.

Note: Please enable the permissions of Storage/Location/Camera for this APP when installing. Otherwise it will have some problems when operating.

Registration

1. If you don't have any account please tap button "Sign up". [UI Mockup: Home screen with Log In, Sign Up, Try now buttons]

2. Read the Privacy Policy and tap "Agree". [UI Mockup: User Agreement and Privacy Policy text with Disagree/Agree buttons]

3. Tap ">" [arrow icon] and choose the country. [UI Mockup: Register screen with input field and country selection arrow]

4. Enter either your mobile phone number or email address. [UI Mockup: Register screen with input field]

5. Tap the button "Get Verification Code". [UI Mockup: Register screen with Get Verification Code button]

[UI Mockup: Country selection screen with search bar and list of countries like Afghanistan, Albania, Algeria, Angola, Argentina, Armenia, Australia]

Login

1. Tap "Log in". [UI Mockup: Login screen with Log In, Sign Up, Try now buttons]

2. Read the Privacy Policy and tap "Agree". [UI Mockup: User Agreement and Privacy Policy text with Disagree/Agree buttons]

3. Enter your registered account and password. [UI Mockup: Login screen with account and password fields]

4. Tap "Log in" button. [UI Mockup: Log in button]

Login - Forgot Password

If you forgot the password or you want to reset the password, operate as below:

1. Tap "Forgot password". [UI Mockup: Login screen with Forgot password link]

2. Enter your account(e-mail address or mobile phone number) and tap button "Get Verification Code". [UI Mockup: Forgot password screen with input field and Get Verification Code button]

3. Enter the verification code received by your e-mail or mobile phone. [UI Mockup: Enter verification code screen]

4. Set the new password and tap button "Done". [UI Mockup: Set Password screen with Done button]

Add Device

There are 4 methods to add the device.

1-EZ mode

1. Power on the indoor unit, no need to launch the air conditioner.
2. Click "+" [plus icon] in the upper right corner of the "Home" screen or tap "Add device". [UI Mockup: Home screen with '+' icon and 'Add Device' button]
3. Tap on the top left "Add Manually" option. On the left side scroll down to "Large Home Appliances". Select the type of device as "Air Conditioner (BLE+Wi-Fi)". [UI Mockup: Add Manually screen showing categories like Electrical, Air Conditioning, Lighting, Sensors, Large Home Appliances, Small Home Appliances, Kitchen Appliances, Exercise & Health, Security & Video Surveillance, Gateway Control. Under Large Home Appliances, select "Air Conditioner (BLE+Wi-Fi)".]
4. Press the "Display" button on the remote controller 6 times within 8 seconds until the device beeps twice and the indoor unit display shows "CF" code. Then press the button at the bottom of the screen to confirm that the device has been reset. [UI Mockup: Reset the device screen, showing indicator blinking rapidly, and a 'Next' button]
5. Input the password of the Wi-Fi that your smartphone is using (2.4Ghz only), then tap "Next". [UI Mockup: Select 2.4 GHz Wi-Fi Network screen with password input and Next button]
6. You can see the connecting process, at the same time "PP", "SA", "AP" shining in turn on the indoor display. "PP" means "Searching the router", "SA" means "connected to the router", "AP" means "connected to the server". [UI Mockup: Adding device screen showing progress, then Added screen with "Device added successfully" and "Rename the device" option]

2-AP mode

1. Power on the indoor unit, no need to launch the air conditioner.
2. Click "+" [plus icon] in the upper right corner of the "Home" screen or tap "Add device". [UI Mockup: Home screen with '+' icon and 'Add Device' button]
3. Select the type of device as "Air Conditioner (BLE+Wi-Fi)". [UI Mockup: Add Manually screen showing categories and selection of "Air Conditioner (BLE+Wi-Fi)".]
4. Tap in the upper right corner and choose "AP Mode". Press the "Display" button on the remote controller 6 times in the time of 8 seconds until the device beeps twice and the indoor unit display shows "CF" code. Then press the button at the bottom of the screen to confirm. [UI Mockup: EZ Mode/AP Mode selection screen, then Reset the device screen showing indicator blinking slowly, and a 'Next' button]

5. Input the password of the Wi-Fi that your smartphone is using (2.4Ghz only), then tap "Next". [UI Mockup: Select 2.4 GHz Wi-Fi Network screen with password input and Next button]

6. Read the instruction carefully and tap "Go to Connect". [UI Mockup: Connect your mobile phone to the device's hotspot screen, showing Wi-Fi settings like "SmartLife-XXXX" or "SL-XXXX", and a "Go to Connect" button]

7. In the wifi setting screen of your smart phone, select "SmartLife-****" or "SL-****", and tap "<" [back arrow]. [UI Mockup: Phone's Wi-Fi settings screen showing available networks.]

8. You can see the connecting process, at the same time "PP","SA","AP" shining in turn on the indoor display. "PP" means "Searching the router", "SA" means "connected to the router", "AP" means "connected to the server". [UI Mockup: Adding device screen showing progress, then Added screen with "Device added successfully" and "Rename the device" option]

3-Bluetooth mode

1. Power on the indoor unit, no need to launch the air conditioner.
2. Click "+" [plus icon] in the upper right corner of the "Home" screen or tap "Add device". [UI Mockup: Home screen with '+' icon and 'Add Device' button]
3. Select the type of device as "Air Conditioner (BLE+Wi-Fi)". [UI Mockup: Add Manually screen showing categories and selection of "Air Conditioner (BLE+Wi-Fi)".]
4. Tap in the upper right corner and choose "Bluetooth" mode. Press the "Display" button on the remote controller 6 times in the time of 8 seconds until the device beeps twice and the indoor unit display shows "CF" code. Then press the button at the bottom of the screen to confirm. [UI Mockup: EZ Mode/AP Mode/Bluetooth selection screen, then Reset the device screen showing indicator blinking rapidly, and a 'Next' button]

5. The app will start searching Bluetooth device. After device found, tap "+" [plus icon] to add the device. [UI Mockup: Searching Bluetooth device nearby screen]

6. Input the password of the Wi-Fi that your smartphone is using (2.4Ghz only), then tap "Next". [UI Mockup: Choose Wi-Fi and enter password screen]

7. Once the connection is completed, you device will appear on the screen. Press Next button and then Done button to complete the process. [UI Mockup: Found devices screen, then Added screen with "Device added successfully" and "Rename the device" option]

8. You can see the connecting process, at the same time "PP","SA","AP" shining in turn on the indoor display. "PP" means "Searching the router", "SA" means "connected to the router", "AP" means "connected to the server".

4-Auto-scan mode

1. Power on the indoor unit, no need to launch the air conditioner.
2. Click "+" [plus icon] in the upper right corner of the "Home" screen or tap "Add device". [UI Mockup: Home screen with '+' icon and 'Add Device' button]
3. Select "Auto Scan" option on the top right hand corner of the screen. Press "Enable Wi-Fi" or "Enable Bluetooth" or both button to launch the connection procedure. [UI Mockup: Add Manually/Auto Scan screen, then Enable permissions screen with Enable Wi-Fi, Enable Bluetooth options]
4. Press the "Display" button on the remote controller 6 times within 8 seconds until the device beeps twice and the indoor unit display shows "CF" code. The app will start auto-scanning. Once the searching is completed you should see the air conditioner found and appearing as "Available devices found". Press "Next". [UI Mockup: Start scanning screen, then Available devices found screen with Air conditioner, then Connecting screen showing progress, then Added screen with "Device added successfully" and "Rename the device" option]
5. Input the password of the Wi-Fi which is the same as your smart phone connected, then tap "Next". [UI Mockup: Choose Wi-Fi and enter password screen]
6. The connecting of the device will start.
7. Once the connection is completed, you device will appear on the screen. Press Done button to complete the process.

Air Conditioner Control

Once your air conditioner is successfully linked up to your network, you can control it from your phone.

Link to Alexa or Google Home for voice control. [UI Mockup: Third-Party Voice Services screen showing Alexa, Google Assistant, SmartThings icons]

Get some help if you meet some problems. And you can report the issues to helpdesk. [UI Mockup: Home Management, Message Center, FAQ & Feedback, Featured, HomeKit Information sections]

Message about Alarms, Home, Notifications

Voice control instructions

[UI Mockup: Amazon Alexa screen with instructions and Sign In With Amazon button]

[UI Mockup: Link to Amazon Alexa screen with instructions and Link with Account Password button]

[UI Mockup: Google Assistant screen with instructions and Link with Google Assistant button]

[UI Mockup: Link to Google Assistant screen with instructions and Link with Account Password button]

Notice and Troubleshooting

Notice

1. Images and functions mentioned in this manual are for reference only and may differ to the model. Please refer to your actual product and app.
2. Smart air conditioner app can be altered without notice for quality improvement and also be deleted depending on the circumstances of manufacturing firms.
3. In case Wi-Fi signal strength is weakened, smart app may be disconnected. Ensure the unit is positioned within range of the wireless router.
4. DHCP server function should be activated for wireless router.
5. The internet connection may fail because of a firewall problem. In this case, contact your internet service provider.
6. For smart phone system security and network setting, ensure smart air conditioner app is marked as a "Trusted" app for firmware updates.

Trouble Shooting