Fortinet Rack Mount Tray SP-RACKTRAY-02 QuickStart Guide

Product Overview

This document provides a quick start guide for the Fortinet Rack Mount Tray, model SP-RACKTRAY-02. It outlines the package contents, device compatibility, and step-by-step installation instructions for various Fortinet devices.

Device Compatibility

The following table lists compatible Fortinet devices and the type of mounting solution (Tray Mount or Adapter Bracket) required.

Model	Type	Supported Devices
FortiGate 30D	Tray Mount (Plastic Housing)	2
FortiGate 30D-POE	Tray Mount (Plastic Housing)	2
FortiGate 30E	Adapter Bracket	2
FortiGate 40F	Adapter Bracket	2
FortiGate 50E/51E	Adapter Bracket	2
FortiGate 50G-DSL	Adapter Bracket	2
FortiGate 60D	Adapter Bracket	2
FortiGate 60D-POE	Adapter Bracket	2
FortiGate 60E/61E	Adapter Bracket	2
FortiGate 60E-POE	Adapter Bracket	2
FortiGate 60F/61F	Adapter Bracket	2
FortiGate Rugged 60F	Tray Mount	2
FortiGate 70D	Tray Mount	1
FortiGate 70D-POE	Tray Mount	1
FortiGate 70F/71F	Adapter Bracket	2
FortiGate 80D	Tray Mount	1
FortiGate 80E/81E	Adapter Bracket	2
FortiGate 80E-POE	Adapter Bracket	2
FortiGate 81E-POE	Adapter Bracket	2
FortiGate 80F/81F/-Bypass	Adapter Bracket	2
FortiGate 90D	Tray Mount	1
FortiGate 90D-POE	Tray Mount	1
FortiGate 90E	Tray Mount	1
FortiGate 90E-POE	Tray Mount	1
FortiGate 90G/91G	Adapter Bracket	2
FortiGate 91E	Tray Mount	1
FortiSwitch 108F	Adapter Bracket	2
FortiVoice Enterprise 100E	Tray Mount	1

The Essentials

For getting started guides, setup and configuration information, refer to the Admin Guides on https://docs.fortinet.com/.

For contracts, licensing, product registration and account management, contact FortiCare Support at https://www.fortinet.com/support/contact.

Access our knowledge base, forums, videos and technical experts at https://www.fortinet.com/support/support-services/forticare-support.

Thank you for choosing Fortinet.

Package Contents

The Fortinet Rack Mount Tray (SP-RACKTRAY-02) package includes:

QuickStart Guide
Fortinet Rack Mount Tray
2x Adapter Brackets
8x Cable Ties
2x Grounding Wires
20x Various Philips M3/M4 Screws
4x Hex Screws
8x Rubber Feet
4x Shoulder Screws

Installation

Before you begin, power off and disconnect the device. If rubber feet are attached, remove them.

Plastic Housing Devices

Attach three rubber feet next to the screw holes.
Illustration shows the underside of a device with three rubber feet being attached near the corners where screw holes are located.
Secure device to the rack tray using two 8mm M3 flathead screws.
Illustration shows a device being placed onto the rack tray. Arrows indicate two 8mm M3 flathead screws being inserted from the bottom of the tray into the device.

Optional: Secure device by using the provided 6mm M3 flathead screws or 3.5 M2.5 D4 shoulder slotted screws.

Tray Mount

Place device to one side of the tray above the tray magnets.
Illustration shows a device being positioned onto the rack tray, aligning with magnetic points.
Attach provided grounding wire to the back of the device.
Illustration shows a grounding wire being connected to the rear of the device.

Adapter Bracket

Before you begin, power off and disconnect the device. If applicable, remove the four 4mm M3 screws from the sides of the device. Note, the adapter bracket will not fit devices wider than 216mm (8.5in).

Insert two hex screws into the bracket.
Illustration shows two hex screws being inserted into an adapter bracket.
Place the device onto the adapter bracket, which uses magnets to secure the device.
Illustration shows a device being placed onto the adapter bracket, with magnets indicated as the securing mechanism.
Place device to one side of the tray above the tray magnets.
Illustration shows a device, now attached to the adapter bracket, being placed onto the rack tray, aligning with magnetic points. Arrows indicate screw placements for securing the bracket to the tray.

Optional: Secure the device bottom with 6mm M3 flathead screws.

Optional: If applicable, secure the device sides to the bracket using four 6mm M3 flathead screws or use up to two screws to secure the bottom.

Attach provided grounding wire from the back of the device to the rack mount using a 6mm M3 panhead screw.
Illustration shows a grounding wire being connected from the back of the device (via the bracket) to the rack mount, using a 6mm M3 panhead screw.

Note: The Kensington security slot on the device is not available when the device is installed in the adapter bracket.

Rack Installation

Illustration shows the rack tray being mounted into a server rack. Rack tray dimensions are provided: (height x width x length): 1.73in x 18.9in x 14in / 44mm x 480mm x 357mm.

Level and line up the rack mount tray ear holes with the rack holes.
Finger tighten four rack screws from the rack tray to the rack.
Verify that the device is level and there is 1.5 inches of space above and below the device.
Tighten the rack screws using a screwdriver.
Connect the power and network connections, then secure the power adapter device using the provided cable ties.

Caution: To avoid personal injury or damage to the device, we recommend that two people mount the rack tray on a rack.

For more information, visit Fortinet.com.

	Fortinet Rack Mount Tray SP-RACKTRAY-02 QuickStart Guide QuickStart Guide for installing the Fortinet Rack Mount Tray (SP-RACKTRAY-02) with compatible FortiGate devices. Includes package contents, installation steps for plastic housing devices, adapter brackets, and rack mounting.
	Fortinet Rack Mount Tray SP-RACKTRAY-02 QuickStart Guide This guide provides installation instructions for the Fortinet Rack Mount Tray (SP-RACKTRAY-02), including device compatibility and package contents.
	FortiGate, FortiSwitch, and FortiAP LAN Edge Deployment Guide A comprehensive guide for deploying Fortinet's LAN Edge Solution, covering the setup and configuration of FortiGate, FortiSwitch, and FortiAP devices for secure wired and wireless network access.
	FortiGate 200F Series QuickStart Guide This guide provides essential information for setting up and operating the FortiGate 200F Series firewall, including hardware overview, setup options, and basic configuration.
	FortiGate 80F Series QuickStart Guide Get started quickly with the FortiGate 80F Series. This guide covers essential setup steps, device registration, package contents, and connectivity options for Fortinet's powerful network security appliances.
	Fortinet FortiOS 7.0.6 Hardware Acceleration Guide A comprehensive guide to Fortinet's FortiOS 7.0.6 hardware acceleration features, detailing NP7, NP6, and CP9 processors, their architectures, configurations, and performance optimization for FortiGate network security appliances.
	Fortinet and Auvik Network Monitoring and Management Solution A comprehensive threat protection solution with deep network visibility and troubleshooting for network professionals, integrating Fortinet's FortiGate, FortiSwitch, and FortiAP with Auvik's automated network monitoring and management software.
	FortiGate 200G Series QuickStart Guide: Setup, Features, and Compliance Concise HTML guide for Fortinet FortiGate 200G Series (FG-200G, FG-201G). Covers essential setup, package contents, front/rear panel details, mounting options, and regulatory compliance information.