Manuals+

WELLFOR Outdoor Storage Shed Assembly Instructions

Product Overview

This document provides detailed instructions for assembling the WELLFOR Outdoor Storage Shed, model MSSG61K1271.

Dimensions:

Area of Installation Requirement:

Minimum clear space required for installation: 77.0 inches (width) x 47.6 inches (depth).

Hardware List

PART NO. Qty.
(Image of G2)G24
(Image of GB)GB2
(Image of GC)GC4
(Image of GD)GD4
(Image of GF)GF2
(Image of F1 screw)F1185
(Image of F2 screw)F280
(Image of F3 screw)F38
(Image of S1 cylinder)S198
(Image of S2 washer)S2130
(Image of part 1)11
(Image of part 2)21
(Image of part 3L)3L1
(Image of part 3R)3R1

Parts List

PART NO. Qty.
(Image of part 20)204
(Image of part 21L)21L1
(Image of part 21R)21R1
(Image of part 25L)25L1
(Image of part 25R)25R1
(Image of part 27)272
(Image of part B1)B14
(Image of part P1A)P1A2
(Image of part P2)P24
(Image of part P3)P35
(Image of part P4A)P4A2
(Image of part P4)P42
(Image of part P5)P52
(Image of part P6)P61
(Image of part P7)P72
(Image of part D1)D11
(Image of part D2)D21

Assembly Steps

STEP 1

Attach part 4L to part 4R using 1x F1 screw for each connection.

Diagram Description: Shows part 4L and 4R being joined. Close-up shows 4x F1 screws (?) being used to secure the connection.

  • Parts: 4L, 4R
  • Hardware: 4x F1 (?)

STEP 2

Attach part 2 to the assembly of 4L and 4R using 1x F1 screw for each connection.

Diagram Description: Shows part 2 being attached to the structure formed in Step 1. Close-up shows 2x F1 screws (?) securing part 2.

  • Parts: 2, 4L, 4R
  • Hardware: 2x F1 (?)

STEP 3

Attach part 1 to the assembly of 4L and 4R using 2x F1 screws.

Diagram Description: Shows part 1 being attached to the structure. Close-up shows 2x F1 screws (?) securing part 1.

  • Parts: 1, 4L, 4R
  • Hardware: 2x F1 (?)

STEP 4

Join parts 3L and 3R using 2x F1 screws for each part.

Diagram Description: Shows parts 3L and 3R being joined. Close-up shows 2x F1 screws (?) securing 3L, and another 2x F1 screws (?) securing 3R.

  • Parts: 3L, 3R
  • Hardware: 4x F1 (?)

STEP 5

Attach part 5 to the base frame using 4x F1 screws.

The floor frame must be level and square or holes will not align. Measure the floor frame diagonally; when the diagonal measurements are equal, the floor frame is square.

Diagram Description: Shows part 5 being attached to the base. Close-up shows 2x F1 screws (?) securing one side of part 5, and another 2x F1 screws (?) securing the other side.

  • Parts: 5
  • Hardware: 4x F1 (?)

STEP 6

Attach panel P2 to the base using 3x F1 screws and 3x S2 washers.

Make the colored side of the steel plate outward.

Diagram Description: Shows panel P2 being attached to the base. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing P2.

  • Parts: P2
  • Hardware: 3x F1 (?), 3x S2 (⚪)

STEP 7

Attach panel P3 to the base using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P3 being attached to the base. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P3.

  • Parts: P3
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 8

Attach another panel P2 to the structure using 3x F1 screws and 3x S2 washers. Rotate the structure 90°.

Diagram Description: Shows another panel P2 being attached. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing P2. The assembly is shown rotated 90°.

  • Parts: P2
  • Hardware: 3x F1 (?), 3x S2 (⚪)

STEP 9

Attach panel P4 using 2x F1 screws and 2x S2 washers.

Diagram Description: Shows panel P4 being attached. Close-up shows 2x F1 screws (?) and 2x S2 washers (⚪) securing P4.

  • Parts: P4
  • Hardware: 2x F1 (?), 2x S2 (⚪)

STEP 10

Attach another panel P2 to the structure using 3x F1 screws and 3x S2 washers. Rotate the structure 90°.

Diagram Description: Shows another panel P2 being attached. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing P2. The assembly is shown rotated 90°.

  • Parts: P2
  • Hardware: 3x F1 (?), 3x S2 (⚪)

STEP 11

Attach another panel P4 using 2x F1 screws and 2x S2 washers.

Diagram Description: Shows another panel P4 being attached. Close-up shows 2x F1 screws (?) and 2x S2 washers (⚪) securing P4.

  • Parts: P4
  • Hardware: 2x F1 (?), 2x S2 (⚪)

STEP 12

Attach another panel P2 to the structure using 3x F1 screws and 3x S2 washers. Rotate the structure 90°.

Diagram Description: Shows another panel P2 being attached. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing P2. The assembly is shown rotated 90°.

  • Parts: P2
  • Hardware: 3x F1 (?), 3x S2 (⚪)

STEP 13

Attach panel P3 using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P3 being attached. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P3.

  • Parts: P3
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 14

Attach part 9 using 2x F1 screws and 2x S2 washers.

Put the side with fewer holes facing up.

Diagram Description: Shows part 9 being attached. Close-up shows 2x F1 screws (?) and 2x S2 washers (⚪) securing part 9.

  • Parts: 9
  • Hardware: 2x F1 (?), 2x S2 (⚪)

STEP 15

Attach part 11 using 4x F1 screws and 4x S2 washers.

Put the side with fewer holes facing up.

Diagram Description: Shows part 11 being attached. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing part 11.

  • Parts: 11
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 16

Attach parts 10L and 10R using 1x F1 screw each.

Put the side with fewer holes facing up.

Diagram Description: Shows parts 10L and 10R being attached. Close-up shows 1x F1 screw (?) securing the connection.

  • Parts: 10L, 10R
  • Hardware: 1x F1 (?)

STEP 17

Attach parts 10L and 10R to the structure using 3x F1 screws and 3x S2 washers for each part. Rotate the structure 90°.

Diagram Description: Shows parts 10L and 10R being attached to the main assembly. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing 10L, and another 3x F1 screws (?) and 3x S2 washers (⚪) securing 10R. The assembly is shown rotated 90°.

  • Parts: 10L, 10R
  • Hardware: 6x F1 (?), 3x S2 (⚪)

STEP 18

Attach part G2 to the ends of parts 7 and 8.

Diagram Description: Shows part G2 being attached to both ends of part 7, and to both ends of part 8. Two G2 parts are used for part 7, and two for part 8.

  • Parts: 7, 8
  • Hardware: 4x G2

STEP 19

Attach part 6 to parts 7 and 8 using 2x F1 screws.

The 2 screws fixed in this step need to be removed and reinstalled later in the following steps.

Diagram Description: Shows part 6 being attached to the assembly of parts 7 and 8. Close-up shows 2x F1 screws (?) securing part 6.

  • Parts: 6, 7, 8
  • Hardware: 2x F1 (?)

STEP 20

Attach parts 7 and 8 to the main structure using 3x F1 screws and 3x S2 washers for each part. Rotate the structure 180°.

Diagram Description: Shows parts 7 and 8 being attached to the main assembly. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing part 7, and another 3x F1 screws (?) and 3x S2 washers (⚪) securing part 8. The assembly is shown rotated 180°.

  • Parts: 7, 8
  • Hardware: 6x F1 (?), 3x S2 (⚪)

STEP 21

Attach panel P3 to the structure using 5x F1 screws and 5x S2 washers. Also use 2x F2 screws.

Diagram Description: Shows panel P3 being attached to the main assembly. Close-up shows 5x F1 screws (?) and 5x S2 washers (⚪) securing P3. Another close-up shows 2x F2 screws (?) being used.

  • Parts: P3
  • Hardware: 5x F1 (?), 5x S2 (⚪), 2x F2 (?)

STEP 22

Attach another panel P3 to the structure using 5x F1 screws and 5x S2 washers. Also use 2x F2 screws. Rotate the structure 90°.

Diagram Description: Shows another panel P3 being attached. Close-up shows 5x F1 screws (?) and 5x S2 washers (⚪) securing P3. Another close-up shows 2x F2 screws (?) being used. The assembly is shown rotated 90°.

  • Parts: P3
  • Hardware: 5x F1 (?), 5x S2 (⚪), 2x F2 (?)

STEP 23

Attach panel P1A using 3x F1 screws and 3x S2 washers. Rotate the structure 90°.

Diagram Description: Shows panel P1A being attached. Close-up shows 3x F1 screws (?) and 3x S2 washers (⚪) securing P1A. The assembly is shown rotated 90°.

  • Parts: P1A
  • Hardware: 3x F1 (?), 3x S2 (⚪)

STEP 24

Attach panel P3 using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P3 being attached. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P3.

  • Parts: P3
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 25

Attach panel P1A using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P1A being attached. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P1A.

  • Parts: P1A
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 26

Attach panel P4A using 2x F1 screws and 2x S2 washers. Keep the small hole on the right.

Diagram Description: Shows panel P4A being attached. Close-up shows 2x F1 screws (?) and 2x S2 washers (⚪) securing P4A. The assembly is shown rotated 180°.

  • Parts: P4A
  • Hardware: 2x F1 (?), 2x S2 (⚪)

STEP 27

Attach panels 25L and 25R using 6x F1 screws and 6x S2 washers for each panel.

Diagram Description: Shows panels 25L and 25R being attached. Close-up shows 6x F1 screws (?) and 6x S2 washers (⚪) securing 25L, and another 6x F1 screws (?) and 6x S2 washers (⚪) securing 25R.

  • Parts: 25L, 25R
  • Hardware: 12x F1 (?), 6x S2 (⚪)

STEP 28

Attach part GF to parts 12L and 12R using 2x F2 screws for each connection.

Diagram Description: Shows part GF being attached to parts 12L and 12R. Close-up shows 2x F2 screws (?) securing GF to 12L, and 2x F2 screws (?) securing GF to 12R.

  • Parts: 12L, 12R, GF
  • Hardware: 4x F2 (?)

STEP 29

Attach part B1 to a frame piece using 2x F2 screws.

Diagram Description: Shows part B1 being attached to a frame. Close-up shows 2x F2 screws (?) securing B1.

  • Parts: B1
  • Hardware: 2x F2 (?)

STEP 30

Attach two B1 parts together using 2x F2 screws.

Diagram Description: Shows two B1 parts being joined. Close-up shows 2x F2 screws (?) securing the connection.

  • Parts: B1, B1
  • Hardware: 2x F2 (?)

STEP 31

Attach a component to the top of the structure using 10x F1 screws. Remove the 2 screws installed in Step 19 before proceeding.

Diagram Description: Shows a component being attached to the top of the shed. Close-up shows 10x F1 screws (?) securing the component. The assembly is shown rotated 180°.

  • Hardware: 10x F1 (?)

STEP 32

Attach parts 21L and 21R to the structure using 6x F1 screws for 21L and 3x F2 screws for 21R. Rotate the structure 90°.

Diagram Description: Shows parts 21L and 21R being attached to the main assembly. Close-up shows 6x F1 screws (?) securing 21L, and 3x F2 screws (?) securing 21R. The assembly is shown rotated 90°.

  • Parts: 21L, 21R
  • Hardware: 6x F1 (?), 3x F2 (?)

STEP 33

Attach panel P5 to the roof structure using 4x F1 screws and 4x S2 washers. Rotate the structure 270°.

Screws on the top panel can't be fixed too tightly in the beginning, and they can only be tightened after all holes are aligned.

Diagram Description: Shows panel P5 being attached to the roof. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P5. The assembly is shown rotated 270°.

  • Parts: P5
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 34

Attach panel P7 to the roof structure using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P7 being attached to the roof. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P7.

  • Parts: P7
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 35

Attach panel P6 to the roof structure using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P6 being attached to the roof. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P6.

  • Parts: P6
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 36

Attach panel P7 to the roof structure using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P7 being attached to the roof. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P7.

  • Parts: P7
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 37

Attach panel P5 to the roof structure using 4x F1 screws and 4x S2 washers.

Diagram Description: Shows panel P5 being attached to the roof. Close-up shows 4x F1 screws (?) and 4x S2 washers (⚪) securing P5.

  • Parts: P5
  • Hardware: 4x F1 (?), 4x S2 (⚪)

STEP 38

Attach part 17 to the roof structure using 2x F1 screws.

Diagram Description: Shows part 17 being attached to the roof. Close-up shows 2x F1 screws (?) securing part 17.

  • Parts: 17
  • Hardware: 2x F1 (?)

STEP 39

Attach part 15 to the structure using 4x F1 screws and 4x GC parts.

Diagram Description: Shows part 15 being attached to the main assembly. Close-up shows 4x F1 screws (?) and 4x GC parts securing part 15.

  • Parts: 15, GC
  • Hardware: 4x F1 (?), 4x GC

STEP 40

Attach part 20 to part D1 using 6x F2 screws.

Diagram Description: Shows part 20 being attached to part D1. Close-up shows 6x F2 screws (?) securing part 20 to D1.

  • Parts: 20, D1
  • Hardware: 6x F2 (?)

STEP 41

Attach part 27 to a base component using 6x F2 screws.

Diagram Description: Shows part 27 being attached to a base component. Close-up shows 6x F2 screws (?) securing part 27.

  • Parts: 27
  • Hardware: 6x F2 (?)

STEP 42

Attach part GB to a base component using 3x F2 screws.

Diagram Description: Shows part GB being attached to a base component. Close-up shows 3x F2 screws (?) securing GB.

  • Parts: GB
  • Hardware: 3x F2 (?)

STEP 43

Attach part 20 to a base component using 10x F2 screws. Also use GD parts. Rotate the structure 180°.

Diagram Description: Shows part 20 being attached to a base component. Close-up shows 10x F2 screws (?) securing part 20. GD parts are also visible. The assembly is shown rotated 180°.

  • Parts: 20, GD
  • Hardware: 10x F2 (?)

STEP 44

Attach part 20 to part D2 using 6x F2 screws.

Diagram Description: Shows part 20 being attached to part D2. Close-up shows 6x F2 screws (?) securing part 20 to D2.

  • Parts: 20, D2
  • Hardware: 6x F2 (?)

STEP 45

Attach part 27 to a base component using 6x F2 screws.

Diagram Description: Shows part 27 being attached to a base component. Close-up shows 6x F2 screws (?) securing part 27.

  • Parts: 27
  • Hardware: 6x F2 (?)

STEP 46

Attach part GB to a base component using 3x F2 screws.

Diagram Description: Shows part GB being attached to a base component. Close-up shows 3x F2 screws (?) securing GB.

  • Parts: GB
  • Hardware: 3x F2 (?)

STEP 47

Attach part 20 to a base component using 10x F2 screws. Also use GD parts. Rotate the structure 180°.

Diagram Description: Shows part 20 being attached to a base component. Close-up shows 10x F2 screws (?) securing part 20. GD parts are also visible. The assembly is shown rotated 180°.

  • Parts: 20, GD
  • Hardware: 10x F2 (?)

STEP 48

Attach part 1 to the main structure using 4x F3 screws.

Diagram Description: Shows part 1 being attached to the main assembly. Close-up shows 4x F3 screws (?) securing part 1.

  • Parts: 1
  • Hardware: 4x F3 (?)

STEP 49

Insert part S1 into the designated holes.

Diagram Description: Shows part S1 being inserted into holes on the shed's door or frame. Close-up shows S1 (cylinder) being inserted.

  • Hardware: S1
Models: MSSG61K1271 Dark Gray Outdoor Storage Shed, MSSG61K1271, Dark Gray Outdoor Storage Shed, Outdoor Storage Shed, Storage Shed, Shed

PDF preview unavailable. Download the PDF instead.

62717099 Adobe PDF library 15.00 Adobe Illustrator 24.1 (Windows)

Related Documents

Preview WELLFOR 7x12 Gazebo Installation Guide and Parts List
Comprehensive installation manual for the WELLFOR 7x12 ft carport shed (AW-HPY-102). Includes parts list, assembly steps, and safety warnings for setting up your temporary outdoor structure.
Preview WELLFOR 10'x20' Canopy Shelter Assembly Instructions
Step-by-step assembly guide for the WELLFOR 10'x20' Canopy Shelter (Model AW-HPY-107YW), including a detailed parts list and textual descriptions of diagrams for setup.
Preview WELLFOR 1-Wall Light Fixtures PM2205-1W Assembly and Installation Guide
Detailed assembly and installation instructions for the WELLFOR 1-Wall Light Fixtures, model PM2205-1W. Includes safety precautions, general information, wiring guidance, and component descriptions.
Preview Pull-Down Kitchen Faucet Installation Guide - WELLFOR WA4014MB02
Comprehensive installation instructions for the WELLFOR WA4014MB02 pull-down kitchen faucet. Includes pre-installation checks, daily maintenance tips, required tools, and step-by-step assembly guidance.
Preview WELLFOR Concealed Shower Installation Guide and Care Instructions
Comprehensive installation guide and cleaning care instructions for the WELLFOR concealed shower system. Includes parts list, step-by-step installation, and maintenance tips.
Preview WELLFOR EP24899US Ice Cream Maker User Manual and Operation Guide
Comprehensive guide for the WELLFOR EP24899US ice cream maker, covering important safety notices, specifications, product features, step-by-step operation instructions, maintenance, troubleshooting, and proper disposal.
Preview WELLFOR Shower Faucet System Installation and Maintenance Guide
Comprehensive installation and maintenance guide for WELLFOR shower faucet systems, detailing setup, troubleshooting, and cleaning procedures. Includes product specifications and contact information.
Preview WELLFOR EP24744US Portable Ice Maker User Manual and Safety Guide
Comprehensive guide for the WELLFOR EP24744US Portable Ice Maker, covering important safety notices, specifications, operation, cleaning, and troubleshooting.