SONGMICS UBCB60 Assembly Manual

Introduction

Guide of Manual

• Please read the following instructions carefully and use the product properly.
• Please keep this manual and hand it over when you transfer the product.
• This summary may not include every detailed information of all variations and considered steps. Please contact SONGMICS when further information and help are needed.
• Copying, reselling, translating or other modification of this instruction manual is forbidden without authorization. © Wuppessen, Inc.

Notes

• Please assemble and use the product in accordance with this instruction. SONGMICS does not take responsibility for any damage or injury caused by improper assembly or use.
• Check the product upon receiving and make sure there is no welding slag or splinter.
• Before assembly, make sure you have all the accessories.
• Regularly check if there is any loosening screw or part.
• Clean the product with a dry soft cloth. Neutral detergent can be used if necessary. Avoid wiping the product with wet or hard items.

Warning

• Since the product contains small parts and sharp screws, please be careful during assembly. No children are allowed during assembly.
• No children are allowed to climb, hang or play around the product in case of any damage or injury.
• Keep plastic packing bags away from children in case of suffocation.
• Keep away from sharp objects and corrosive materials.

Parts List

A x 1

B x 1

C x 1

D x 2

E x 1

F x 1

G x 2

H x 1

I x 1

K 8+1

N x 2

O x 2

P 8+1

Q 8+1

R 8+1

S x 2

T x 4

U x 2

V x 2

W x 2

X 8+1

Assembly Steps

Step 1

Attach part P (screw) and part Q (cam lock) to part A (side panel). Two sets of P and Q are used.

Step 2

Attach part C (shelf) to part A using part S (screws). One set of S is used.

Step 3

Attach part C (shelf) to another part A using part R (screws). Two sets of R are used.

Step 4

Attach part B (bottom panel) to the assembled side panels using parts P, Q, and R. Two sets of P, Q, and R are used.

Step 5

Insert part E (back panel support) into the grooves of the side panels. Insert parts D (dowels) into the pre-drilled holes.

Step 6

Attach part F (top panel) to the side panels using parts P, Q, and S. Four sets of P and Q, and one set of S are used.

Step 7

Attach part F (top panel) to the side panels using part R. Four sets of R are used.

Step 8

Insert part G (shelf support) into the pre-drilled holes on the side panels. Eight sets of K (shelf pins) are used.

Step 9

Assemble the shelves. Attach part H (slatted shelf) and part I (slatted shelf) using parts T (screws) and U (cam locks). Four sets of T and two sets of U are used. Then attach part N (door hinge) and part O (door hinge) to the shelves.

Step 10

Attach the assembled shelves to the cabinet frame using parts N and O. Two sets of N and two sets of O are used.

Step 11

The cabinet is now assembled.

Step 12

Attach part W (door hinge) to the doors using part X (screws). Two sets of W and eight sets of X are used.

Step 13

Attach the doors to the cabinet using part V (screws). Two sets of V are used.

Customer Service and Feedback

Thank you for your purchase. If you have difficulty with assembly or need replacement parts, please contact SONGMICS Customer Service.

Email: customerservice@songmics.com

Please attach your User Name or Order ID to assist you better.

Visit www.songmics.com or scan the QR code for more product details.

You may also find "Songmics" on Facebook and YouTube.

Share your shopping experience with friends and families. Like "Songmics" on Facebook for more Amazon deals & promotions.

For any questions or feedback, please email us with your order ID. We are always striving to improve.

Contact: customerservice@songmics.com | www.songmics.com

© 2017 Wuppessen Inc. 1730 Cedar St. Ontario, CA, 91761, U.S. All rights reserved.

Version QM: 1.0

Stand: 14.09.2017