SONGMICS GLR040 Storage Shelving Unit

General Guidelines & Introduction

Please read these instructions carefully and use the product as intended. Keep this manual for future reference and pass it on if the product is transferred to a third party. This summary may not cover every detail of all variations and steps; please contact us for further information or assistance.

Important Notes

• The shelving unit is designed for indoor use only. Unauthorized modifications or uses not described in this manual are not permitted and may result in personal injury or product damage. Assemble and use the product strictly according to the manual. The seller is not liable for damages caused by incorrect assembly or improper use.
• After unpacking, check the shipping list to ensure all parts are present and undamaged.
• Assembly is recommended for two adults. Wear gloves ? during assembly to prevent injuries. Additional safety measures may be necessary.
• Recommended tools (not included): gloves ?, a rubber hammer ?, and a flat-head screwdriver ⛋.
• Place the unit on a flat, horizontal, and hard surface to ensure stability and load capacity.
• Do not shake the assembled unit, as this will affect its stability.
• The unit should be placed against a wall and securely fixed. Use wall plugs and screws appropriate for your wall type. Consult local dealers for advice.
• When drilling into walls, avoid water pipes and electrical cables ⚡.
• Remove all items from the unit before assembly or disassembly.
• To move the unit, disassemble it completely to prevent damage and injury. Save all components. Do not drag the unit.
• Distribute weight evenly on the shelves to prevent damage to the panels. Do not exceed the maximum load per shelf or for the entire unit.
• Avoid placing the unit in high humidity areas, as this can damage the wooden panels.
• For cleaning, wipe with a damp cloth ?, then dry with a dry cloth.

Warnings

• Do not step on or climb the unit. ??
• Serious or fatal injuries may occur if the unit overturns ⚠️.
• This product is not intended for children. Do not allow children to climb or play on the unit to prevent serious injury from tipping. ??
• Do not alter or omit any components, as this will significantly affect the product's function.
• To prevent suffocation hazards, keep all parts and packaging (films, plastic bags, foam, etc.) away from babies and children. ?

Parts List

• Part A: Shelf Panel (x5)
• Part B: Vertical Frame / Upright (x8) - Long metal piece with multiple slots.
• Part C: Long Shelf Support Beam (x10) - Rectangular metal piece, 4.5 x 89cm, with integrated clips/slots.
• Part D: Short Shelf Support Beam (x10) - Rectangular metal piece, 4.5 x 39cm, with integrated clips/slots.
• Part E: Foot Cap (x4) - Black plastic cup-shaped pieces for the bottom of the frames.
• Part F: Cross Brace / Stabilizer (x5) - Angled metal piece with tabs for connection.
• Part G: Corner Connector / Bracket (x8) - L-shaped metal pieces used for joining frames.
• Part H: Anti-tip Wall Anchor Kit (x2) - Straps and hardware for securing the unit to the wall.
• Part I: Wall Plug and Screw (x2) - For wall mounting.

Assembly Instructions

1. Step 1: Prepare Vertical Frames

   Attach corner connectors (G) to the top ends of four vertical frames (B). The diagram shows two sets of frames being prepared.

2. Step 2: Install Short Shelf Supports

   Insert the clips of the short shelf supports (D) into the slots on the inner sides of the vertical frames (B). Ensure they are fully inserted to form a firm joint.

3. Step 3: Install Long Shelf Supports

   Insert the clips of the long shelf supports (C) into the slots on the inner sides of the vertical frames (B). Ensure they are fully inserted to form a firm joint.

4. Step 4: Attach Cross Braces

   Bend the tabs of the cross braces (F) to 90 degrees. Insert these tabs into the slots located in the middle of the long shelf supports (C). Bend the tips of the tabs to 90 degrees to secure the connection and prevent detachment.

5. Step 5: Attach Foot Caps

   Push the foot caps (E) onto the bottom of the vertical frames (B).

6. Step 6: Assemble Second Unit Half & Join

   Assemble the second half of the shelving unit by repeating steps similar to 2 and 3 with the remaining vertical frames (B) and short shelf supports (D). Then, join the two halves to form the complete frame structure.

7. Step 7: Complete Frame Structure

   The frame structure is now assembled, ready for shelves. Shelves (A) will rest on supports (C and D).

8. Step 8: Position Unit

   Move the assembled shelving unit to its desired location, preferably against a wall ?.

9. Step 9: Prepare Wall for Anchoring

   Drill holes into the wall at the appropriate height for the anti-tip devices.

10. Step 10: Insert Wall Plugs

    Insert the wall plugs (I) into the drilled holes in the wall.

11. Step 11: Secure Unit to Wall

    Attach the anti-tip devices (H) to the shelving unit and secure them to the wall using the provided screws. This prevents tipping hazards caused by uneven ground or unevenly distributed items.

12. Step 12: Place Shelves

    Place the shelf panels (A) onto the installed shelf supports (C and D). Ensure they are seated correctly.

13. Step 13: Final Check

    Ensure all parts are securely fastened. The unit is now ready for use.