ZALMAN Z3 Iceberg ATX Mid Tower Computer Case - User's Manual
Introduction
This manual provides instructions for the ZALMAN Z3 Iceberg ATX Mid Tower Computer Case.
Compatibility: The Z3 Iceberg supports Razer Chroma™ compatibility through Z-Sync or hardware support.
Note: Product design and specifications are subject to change for quality improvement without prior notice.
Precautions
- Read this manual carefully before installation.
- Check the product and components before installation. Contact the place of purchase for replacement or refund if any abnormality is found.
- Wear gloves ? to prevent accidents during installation.
- Do not apply excessive force during system mounting to avoid severe damage.
- Ensure correct cable connections as incorrect wiring may cause a fire due to a short circuit. Refer to the manual for cable connections.
- Do not block the product's ventilation holes when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated area.
- Do not clean the product surface with chemicals (e.g., organic solvents like alcohol or acetone).
- Do not insert hands or objects into the product during operation to prevent injury or damage.
- Store and use the product out of children's reach.
- ZALMAN is not responsible for problems arising from use for purposes other than intended or from consumer carelessness.
Technical Specifications
| Specification | Details |
|---|---|
| Model | Z3 Iceberg KOR / Z3 Iceberg |
| Case Form Factor | ATX Mid-Tower |
| Dimensions | 410 x 210 x 480(H)mm |
| Weight | 6.6kg / 6.4kg |
| Case Materials | Plastic, Steel, Tempered Glass |
| Motherboard Support | E-ATX(~280mm) / ATX / mATX / Mini-ITX |
| Maximum VGA Length | 315mm |
| Maximum CPU Cooler Height | 163mm |
| Maximum PSU Length | 160mm |
| PCI Expansion Slots | 7 |
| Drive Bays | 2 x 3.5" (2 x Combo, 1 x Toolless), 4 x 2.5" |
| Fan Support (Top) | 2 x 120mm / 2 x 140mm |
| Fan Support (Front) | 3 x 120mm / 3 x 140mm |
| Fan Support (Rear) | 3 x 120mm |
| Fans Included (Front) | 3 x 120mm (with White LED Effect) |
| Fans Included (Rear) | 1 x 120mm (with White LED Effect) |
| Fans Included (Top) | 1 x 120mm (Addressable RGB) |
| Fans Included (Rear) | 1 x 120mm (Addressable RGB) |
| ARGB Controller | Included |
| Radiator Support (Top) | 120mm / 240mm |
| Radiator Support (Front) | 120mm / 240mm / 280mm / 360mm |
| Radiator Support (Rear) | 120mm |
| I/O Ports | 1 x Headphone, 1 x Mic, 1 x USB 2.0, 2 x USB 3.0, Power Button, Reset Button, LED Button |
Included Components
The package typically includes the following components:
- Manual
- Zummer (Speaker)
- 2 x PCI Slot Covers
- 5 x Cable Ties
- Glass Cleaner
- 3 x USB Port Dust Covers
- 6 x Fan Screws ?
- 2 x Motherboard Standoffs
- 2 x Motherboard Screws ?
- 8 x HDD Screws ?
- 2 x SSD/MB Screws ?
- 8 x PSU/VGA Screws ?
- 6 x Motherboard Standoffs
Visual description: The components are shown in small diagrams, including screws, standoffs, cable ties, a speaker, a glass cleaner, and dust covers.
Installation Guide
1. Removing the Side Panels
Visual description: Diagrams show how to slide and remove the left and right side panels of the computer case.
2. Removing the Front Panel
Visual description: A diagram illustrates how to detach the front panel. A warning symbol ⚠️ indicates sharp edges on the air vent.
3. Mounting the Motherboard
Visual description: Diagrams show installing motherboard standoffs ? and then placing the motherboard onto them, securing it with screws ?. Motherboard sizes supported (E-ATX, ATX, mATX, Mini-ITX) are illustrated.
4. Mounting PCI-E(VGA) Card
Visual description: Diagrams show installing a graphics card (VGA) into a PCI-E slot and securing it with screws ?.
5. Mounting the 2.5" SSD
Visual description: Diagrams illustrate mounting 2.5" SSDs in various locations within the case, using screws ?.
6. Mounting the 3.5" and 2.5" SSD / HDD
Visual description: Diagrams show how to install 3.5" HDDs and 2.5" SSDs. A note indicates that 3.5" HDDs can be mounted without bolting (tool-less).
7. Mounting the PSU
Visual description: Diagrams show the process of installing the Power Supply Unit (PSU) into its designated bay and securing it with screws ?.
8. Mounting the Radiator
Visual description: Diagrams show the placement options for radiators: front (120mm, 240mm, 280mm, 360mm), top (120mm, 240mm), and rear (120mm).
9. Mounting the Fans
Visual description: Diagrams illustrate fan installation: top (2 x 120mm or 2 x 140mm), front (3 x 120mm or 3 x 140mm), and rear/bottom (1 x 120mm or 2 x 120mm).
10. Fan(s) Included / Fan Specifications
The Z3 Iceberg comes with:
- Z3 Iceberg: Front/Rear fans (120mm, 1300 RPM, Hydro Bearing, 3-PIN connector). Includes Addressable RGB LED fans (DC 5V 0.72A for LED).
- Z3 Iceberg KOR: Front fans (White LED, 120mm, 1200 RPM, Hydro Bearing, IDE-4PIN connector) and Rear fan (White LED, 120mm, 1200 RPM, Hydro Bearing, 3-PIN connector).
11. I/O Connectors
Visual description: Diagrams show the front panel I/O connectors: HDD LED, Reset Button, Power Button, Power LED, HD Audio, USB 2.0, USB 3.0, and LED Button. It also details ARGB LED connections (5V, DATA, GND) and SATA Power connection.
Warranty and Service
Warranty Period: 1 year from the date of purchase (with proof of purchase).
Free A/S (After-Sales Service): Covered for product performance defects within the warranty period.
Paid A/S: For issues after the warranty period or due to user error, negligence, or unauthorized modification.
Service Hours: Weekdays 10:00 - 16:00 (Closed on weekends and holidays).
Service Contact: Visit www.zalmansvc.com for online service requests (visit or mail-in).
Shipping Costs: Covered by ZALMAN for initial defects. For free A/S, customer covers one-way shipping. For paid A/S, customer covers round-trip shipping.
Parts Retention Period: 2 years from product discontinuation.
Certification: CE, RoHS compliant.
zalman
