Important Safety Notice
Product is NOT INTENDED for the following:
- As a safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
- As load bearing support for a building, structure, heavy objects or swings.
- Used in structures that trap wind, rain or snow that would create extra load on the product.
Accumulated snow must be removed from roof. DO NOT climb or walk on roof for any reason.
Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.
During installation, follow all safety warnings provided with your tools.
Some structures may require two or more people to install safely.
Check for underground utilities before digging or driving stakes into the ground!
It is important during assembly to closely follow the instructions, complete the assembly on a solid level surface and that you follow the instruction to square up, level and anchor the structure, this will reduce the gap at connections during assembly.
Packing Details: Total 4 Boxes
Box 1/4:
| NO. | PARTS | QTY |
|---|---|---|
| A | [Straight Pole] | 4pcs |
| E | [Angled Pole] | 4pcs |
Box 2/4:
| NO. | PARTS | QTY | NO. | PARTS | QTY |
|---|---|---|---|---|---|
| B | [Long Beam] | 2pcs | F | [Short Beam] | 4pcs |
| B1 | [Short Beam] | 2pcs | G | [Connector Piece] | 4pcs |
| C | [Corner Bracket] | 2pcs | H | [Small Connector] | 2pcs |
| C1 | [Corner Bracket] | 2pcs | I | [Long Connector] | 4pcs |
| D | [Roof Support] | 6pcs | J | [Small Bracket] | 4pcs |
| K | [Small Bracket] | 2pcs | L | [Curtain Hook] | 4pcs |
| M | [Curtain Hook] | 4pcs | N | [Support Rod] | 8pcs |
| S | [Foot Plate] | 4pcs |
Box 3/4:
| NO. | PARTS | QTY | NO. | PARTS | QTY |
|---|---|---|---|---|---|
| O | [Center Connector] | 1pc | X1 | [M6*15 Screw] | 105pcs |
| P | [Roof Support] | 1pc | X2 | [M6*40 Screw] | 16pcs |
| Q | [Roof Panel Connector] | 6pcs | X3 | [M6*55 Screw] | 8pcs |
| R | [Washer] | 4pcs | X4 | [M6*55 Screw] | 8pcs |
| T | [Roof Panel] | 8pcs | Y | [Nut] | 113pcs |
| U1 | [Curtain Slider] | 8pcs | Z1 | [Bolt] | 8pcs |
| U2 | [Curtain Slider] | 8pcs | Z2 | [Curtain Rod Connector] | 16pcs |
| V | [Roof Support] | 6pcs | [Curtain Tie-back] | 2pcs | |
| W | [Curtain] | 4pcs | [Allen Wrench] | 1pc | |
| [Allen Wrench] | 1pc |
Box 4/4:
| NO. | 1 | 3 | 4 |
|---|---|---|---|
| PARTS | [Roof Panel] | [Roof Panel] | [Roof Panel] |
| QTY | 4pcs | 2pcs | 4pcs |
| NO. | 2 | 3 | 5 |
|---|---|---|---|
| PARTS | [Roof Panel] | [Roof Panel] | [Roof Panel] |
| QTY | 4pcs | 2pcs | 4pcs |
Assembly Steps
Step 1:
Attach foot plates (S) to the bottom of poles (A) using screws (X1) and nuts (Y). 4 sets required.
Step 2:
Connect beams (B, B1) and corner brackets (C, C1) to the poles (A) using screws (X1) and nuts (Y). 8 sets of X1 and 40 sets of Y are used in this step.
Step 3:
Attach roof supports (T, V) and corner brackets (C, C1) to the beams (B, B1) using screws (X1, X3) and nuts (Z1, Y). 16 sets of X1, 8 sets of X3, 8 sets of Z1, and 24 sets of Y are used.
Step 4:
Attach the center connector (O) to the angled poles (E) using screws (X1) and nuts (Y). 4 sets required.
Step 5:
Assemble the main roof structure by attaching angled poles (E) and roof supports (C, C1, B, B1) using screws (X1) and nuts (Y). 4 sets of X1 and 4 sets of Y are used.
Step 6:
Attach roof supports (D, V) to the roof structure using screws (X1) and nuts (Y). 20 sets of X1 and 20 sets of Y are used.
Step 7:
Install the central roof support (P) using screws (X1) and nuts (Y). 3 sets required.
Step 8:
Attach curtain sliders (U1, U2) and connectors (L, M) to the roof beams (B, B1, C, C1) using screws (X2). 16 sets of X2 are used.
Step 9:
Assemble the roof panels (1, 2, 3, 4, 5) and attach them to the roof structure using screws (X1) and nuts (Y). 10 sets of X1 and 10 sets of Y are used.
Step 10:
Hang the curtains (W) using the curtain sliders (U1, U2) and curtain rod connectors (Z2). Attach foot plates (S) to poles (A) with screws (X4) if needed, or use Z2 for alternative attachment.
