Pioneer VSX-LX505 Initial Setup Guide
This guide provides the initial setup steps for the Pioneer VSX-LX505 AV Receiver.
STEP 1: Speaker Connection
This section details the initial connection of speakers to the AV receiver.
Important Note: This document uses a 7.1 channel system as an example. For systems other than 7.1, or for multi-zone features and other detailed operating instructions, refer to the online instruction manual.
Info Icon ?: This icon indicates an important setting. Ensure you confirm the setting during the "Initial Setup" process (STEP 3).
7.1 Channel System Speaker Layout:
- FL, FR: Front Speakers
- C: Center Speaker
- SL, SR: Surround Speakers
- SW: Powered Subwoofer
- SBL, SBR: Surround Back Speakers
Speaker Placement Angles:
- a: 22° to 30°
- b: 90° to 110°
- c: 135° to 150°
Connecting Speakers:
Connect speakers with an impedance of 4 Ω to 16 Ω. Twist the ends of the speaker cable wires tightly.
Diagram Description: The rear panel of the VSX-LX505 is shown with various input and output terminals labeled. Speaker terminals are highlighted, showing connections for FL, FR, C, SL, SR, SW, SBL, and SBR. Arrows indicate where to connect the speaker cables, with specific terminals marked for impedance ranges (4-16Ω) and bi-amping.
Rear Panel Connections Overview:
- HDMI IN (ASSIGNABLE 1-4): For connecting HDMI sources.
- HDMI OUT: For connecting to a display.
- DIGITAL AUDIO IN (OPTICAL, COAXIAL): For digital audio sources.
- ANALOG AUDIO IN: For analog audio sources.
- COMPONENT VIDEO IN: For component video sources.
- NETWORK (Ethernet): For network connectivity.
- USB: For USB devices.
- CONTROL (IR IN, 12V TRIGGER OUT, SIGNAL GND): For control systems.
- ANTENNA (AM, FM): For radio reception.
- AC IN: Power connection.
STEP 2: Connecting Sources
This step involves connecting your audio and video sources to the receiver.
Diagram Description: The diagram shows connections for digital optical and HDMI cables from source devices (like Blu-ray players or game consoles) to the corresponding inputs on the AV receiver. It also illustrates antenna connections for AM/FM radio.
Connecting HDMI and Digital Optical Cables:
Connect your devices using HDMI cables to the HDMI IN ports and digital optical cables to the OPTICAL IN ports on the receiver.
Connecting AM/FM Antennas:
Connect the provided AM and FM antennas to the respective terminals on the rear panel.
STEP 3: Initial Setup
This step guides you through the on-screen initial setup process.
TV Input Selection:
Info Icon ?: Switch the input on your TV to the one assigned to the unit (e.g., HDMI 1, HDMI 2).
On-Screen Setup Menu:
Diagram Description: The screen displays the initial setup menu options on the TV, including language selection, network connection, speaker setup, and other configurations. The receiver's remote control is shown with the SETUP MIC and other relevant buttons.
- Select Language: Choose your preferred language for the setup menu.
- Network Connection: Configure network settings (wired or wireless).
- Speaker Setup: Configure speaker settings (e.g., size, distance).
- Other Settings: Further configurations like Dirac Live / Full Auto MCA may be available.
Troubleshooting:
If you encounter issues during setup:
- Restart: Try restarting the unit by putting it into standby mode and then powering it back on.
- Initialize Settings: If the problem persists, you may need to initialize the settings. This is typically done via the "System Setup" > "Miscellaneous" > "Initial Setup" menu while the unit is ON.
- Check Connections: Ensure all cables are securely connected.
- Update Firmware: Consider updating the unit's firmware if available.
Diagram Description: Visuals show the process of restarting the unit (using the standby button) and initializing the settings (likely involving a button combination or menu option).
