Akuvox Smart Intercom E12 Quick Guide

Unpacking

Before using the device, check the version obtained and ensure the following items are included in the shipped box:

Universal Accessories:

• E12 x 1
• Wall mounting bracket x 1
• ST4x20 screw x 4
• Torx screw x 2
• Plastic Wall Anchor x 4
• Back cover x 1
• M3x4 screw x 4
• Torx Wrench x 1
• 7-pin cable x 1
• 6-pin cable x 1
• Wall-mounting template x 1
• Diode x 1

Product Overview

The Akuvox E12 features:

• Mic
• Photosensitive sensor
• Camera
• RF card reader
• Call button

Installation Environment

Indoor and outdoor installation are supported.

• Outdoors: Do not place the device under direct sunlight.
• Indoors: Keep the device at least 2 meters away from light, and at least 3 meters away from windows and doors.

Avoid:

• Backlight
• Direct sunlight
• Direct sun through window
• Indirect sunlight through window
• Close to light

Installation

1. According to the position of the reserved wires on the wall, stick the wall-mounting template vertically to ensure wires can come out of the shadow position of the template.
2. Drill four screw holes (6 mm drill bit required) with a depth of 25mm in the screw holes of the template.
3. Insert four plastic wall anchors into the holes.
4. Fix the wall-mounting bracket on the wall by tightening four STx20 screws to the plastic wall anchors.
5. Connect the wires to the interface of the device as needed (refer to "Device Wiring"). After arranging the wires, tighten the back cover using four M3x4 screws to the device.
6. Hang the device on the two square hangers on the wall-mounting bracket, then use the Torx Wrench to tighten the bottom of the device with two Torx screws.

The installation is completed.

Application Network Topology

The E12 can be connected within a network including:

• SIP Video Phone (PoE)
• Indoor Monitor (PoE)
• PC (third party)

The E12 connects via LAN using PoE.

Device Wiring

The device has the following wiring connections:

• Power Input: 12V, GND
• Relay Output: NC, NO, COM
• Wiegand Input/Output: WG_D0, WG_D1, GND
• Wiegand Card Reader: WG_D0, WG_D1, GND
• Door Lock: NC, NO, COM
• Exit Input: Exit A, Exit B, GND
• Door A: DOOR A
• Door B: DOOR B

Warning: When connecting a device with a coil (e.g., relay or electromagnetic lock), protect the intercom against voltage peaks by connecting a diode (1 A / 200 V, included) antiparallel to the device.

Diode Terminals: + , -

IP Announcement

1. While E12 starts up normally, hold the call button for several seconds after the LED light turns blue; the voice system will enter IP announcement mode.
2. In announcement mode, the IP address will be announced periodically.
3. Press the Call Button again to exit the announcement mode.
4. In announcement mode, the phone announces "IP 0.0.0.0" if no IP address is gained.

Operation

Make a call:

1. Press the call button to call the indoor SIP Phone.
2. During the talk, the called party can press a pre-configured code number to unlock the door.

Receive a call:

E12 supports Auto Answer by default. Incoming calls from indoor devices will be answered automatically.

Configuration

1. Access the Web UI: Input the IP address into a web browser to configure the phone.
2. Account Registration: On the Web UI, go to the path: Account -> Basic page. Register the account and fill in the account information. (Please refer to the user manual for more information).
3. Configure the Push Button: On the Web UI, go to the path: Intercom -> Basic -> Push Button to configure the call number.
4. Configure the code to open the relay: On the Web UI, go to the path: Intercom -> Relay&Input -> Relay ID/DTMF and choose the DTMF code number in the corresponding area.

Indicators

Note: For more LED settings, please refer to the E12 webUI: Intercom -> LED Setting.

Notice Information

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without notice. Any update to this document can be viewed on Akuvox's website: http://www.akuvox.com. Copyright 2021 Akuvox Ltd. All rights reserved.

AKUVOX (XIAMEN) NETWORKS CO., LTD.
ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA
www.akuvox.com