ULINE H-8226 96" Packing Station

Legs and Frame Assembly

ℹ️ NOTE: Tabletops add 1½ – 1¾" depending on top purchased.

1. Flip legs (1 and 2) upside down. Place adjustable feet (3) into legs and slide to desired height. Fasten adjustable feet to legs with two M10 x 65 hex bolts and two M10 nuts per adjustable foot using a 17 mm wrench.
2. Turn legs upright and spread apart to accommodate frame support bars (4). Position frame support bars so that the larger holes are facing down. The open end of frame support bars should be positioned on the center leg (1). Fasten support bars to outside leg (2) with four M8 x 65 hex bolts per leg using a 13 mm wrench. Repeat for the other side.
3. Place center leg support bar (8) between frame support bars (4) on top of the center leg. Fasten center leg support bar to frame support bars and center leg (1) with eight M8 x 65 hex bolts using a 13 mm wrench.

Bottom Shelf Assembly

ℹ️ NOTE: Bottom shelf is a two-piece design. One end of each piece has a channel to rest shelf on top of the leg brace on the outside legs. The other end is flat and will bolt to the center leg's brace.

1. Place the end of each shelf piece with the channel across the leg brace of the outside legs. Have two people hold up the end of the shelves that face the center leg (1) and align the holes on the side of the shelf pieces to the holes in the center leg brace. Fasten shelf pieces to center leg brace with three M8 x 65 hex bolts and three M8 nuts using a 13 mm wrench.
2. Fasten end of each shelf piece to the leg brace of the outside legs with six M8 x 35 hex bolts and six M8 nuts per shelf using a 13 mm wrench.

Top Assembly

1. To attach tabletop (10) onto frame assembly, place tabletop on a smooth, non-marring surface with top side facing down.
2. Rotate assembled frame upside down and line up two pre-drilled holes on back corners of table top. Do not insert screws into these two holes and the two holes in front of them at this time.
3. Using all other hole locations in frame as a template, drill 3/4" deep pilot holes into tabletop using a 3/16" drill bit. Using 14 (16 for 72" table) wood screws and a drill with a Phillips head drill bit, attach frame to underside of tabletop in these new pilot holes.
4. Using a 1/4" drill bit, drill four holes all the way through tabletop in hole locations shown in Figure 9. They should line up with holes in back of leg. These will be used to attach uprights later.
5. Carefully set table upright and recheck all screws for tightness.
6. Place two storage shelf support brackets (6) onto inside of outside legs (2) with lip side facing down and inside frame. Fasten each support bracket to legs with two M10 x 65 hex bolts and two M10 nuts using a 17 mm wrench.
7. Slide the end of each shelf piece on top of the storage shelf support bracket. Have two people hold up the end of the shelves that face the center leg and align the holes on the side of the shelf pieces to the holes in the center leg's middle brace. Fasten shelf pieces to center leg's middle brace with three M8 x 65 hex bolts and three M8 nuts using a 13 mm wrench.

ℹ️ NOTE: Additional pre-drilled holes in tabletop are used for a different product and will not align with this frame. You must pre-drill your own pilot holes.

ℹ️ NOTE: Wood screws for front and back of frame are optional but provide more support.

Bottom Shelf Divider Assembly

1. Four bottom shelf dividers are included with packing station. To attach, slide shelf dividers between full depth bottom shelf and 4" high storage shelf and align with two pre-drilled holes in each shelf. Fasten each divider with four M6 Phillips head bolts and four M6 flange nuts using a Phillips screwdriver and 10 mm wrench.

Upright Assembly

1. Position upright on back corner of tabletop. The mounting plate should be positioned directly over the previously drilled holes. Fasten four M6 x 70 hex bolts and flat washers through uprights, tabletop and legs using a 10 mm wrench. Secure with four M6 flange nuts on underside of table.
2. Repeat with second upright.

Bin Rail Assembly

1. Line up bin rail (1) with uprights at desired height.
2. Secure to uprights with four 1½" bolts and flange nuts.

Reel Holder Assembly

1. Line up reel holder brackets (3) with uprights at desired height.
2. Secure to uprights with four M6 x 40 mm hex bolts and flange nuts.
3. Place reel (4) inside bracket grooves.

ℹ️ NOTE: Six core plugs are included. Insert into label or paper roll to reduce diameter for better fit on reel.

Monitor Arm Assembly

1. Line up monitor arm mounting bracket (2) with uprights at desired height.
2. Secure to uprights with two M6 x 35 mm or M6 x 50 mm Allen head bolts, two small flat washers and two hex nuts using an Allen wrench and 10 mm wrench.
3. The easy-adjust monitor mount includes a built-in counterweight system for free-range motion. The arm in the mount may need to be adjusted to allow the monitor to stop at the desired position. Attach monitor to plate.
4. To adjust the counterweight, use a 5 x 5 Allen wrench on the screw above the middle joint. Turn towards "-" if the monitor raises up. Turn towards "+" if the monitor lowers. Adjust until the mount can be stopped at the desired position.

Attaching Monitor

ℹ️ NOTE: Make sure monitor has a VESA hole pattern of 100 x 100 mm or 75 x 75 mm.

ℹ️ NOTE: If monitor is attached to a fixed base, remove monitor from base.

⚠️ CAUTION! Be careful not to scratch screen during installation.

Cable Management

1. To remove covers, use a Phillips head screwdriver to unscrew the two screws securing covers to the monitor arm. This allows the user to slide cables through the covers. Once complete, re-secure the covers to the monitor arm using the Phillips head screws.

12" Deep Top Shelf Assembly

1. Line up shelf brackets (5) with uprights at desired height.
2. Secure to uprights with four 1½" bolts and flange nuts.
3. Place shelf (6) on brackets. Install to brackets with four 5/8" bolts and flange nuts.

12" Deep Top Shelf Divider Assembly

1. Line up the front "C" channel of divider (7) with the front lip of the top shelf. Insert divider into front lip at an angle. Once in place, allow divider to drop and magnetize to the back shelf lip.

16" Deep Box Shelf Assembly

1. Line up shelf brackets (8) with uprights at desired height.
2. Secure to uprights with four 1½" bolts and flange nuts.
3. Place shelf (9) on brackets. Install to brackets with four 5/8" bolts and flange nuts.

16" Deep Box Shelf Divider Assembly

1. Six box shelf dividers (10) are included with box shelf. To attach, line up front and rear pre-drilled holes on top of shelf. Fasten each divider with two Phillips head bolts and two M6 flange nuts using a Phillips screwdriver and 10 mm wrench.

Light Kit Assembly

1. Line up light brackets (12) with uprights at desired height.
2. Secure to uprights with four 2" bolts and flange nuts.
3. Place light steel beam (13) at desired depth underneath brackets. Fasten to brackets with two 4¾" bolts and flange nuts.
4. Place two "S" hooks (14) at desired mounting points along the steel beam and secure with two flange nuts.
5. Attach hanging chains to LED shop light (11) and mount to "S" hooks.

Tabletop Power Strip Assembly

1. Choose desired location for power strip (15). Place two supplied mounting clips roughly 32" apart (clip side up). Using an electric drill, fasten to tabletop with two supplied wood screws.
2. Secure power strip by snapping into the mounting clips.

Tape Gun Holder Assembly

ℹ️ NOTE: Tape Gun Holder can be attached to uprights or bin rail.

1. If attaching to bin rail, no assembly is needed. Place the back folded lip of the bracket over the bin rail. Push down to ensure it is set firmly in place.
2. If attaching to uprights, slide tape gun upright bracket underneath tape gun holder and align the holes in the bracket to the holes on top of the holder. Attach with two M5 x 10 mm pan head screws and two M5 flange nuts using a Phillips screwdriver and 8 mm wrench.
3. Align gun holder and upright bracket with uprights at desired height.
4. Secure to uprights with two M6 x 40 mm hex bolts and two M6 flange nuts.

Fan Assembly

ℹ️ NOTE: Fan comes with 6" and 10" long bracket. Choose desired bracket based on application.

1. Slot 6" or 10" fan mounting bracket between opening in fan upright mounting bracket. Align holes of each bracket and attach using two M6 x 12 mm hex bolts and two M6 flange nuts.
2. Align hole on the opposite end of fan mounting bracket to the hole on the crescent fan bracket. Attach using M12 x 20 mm hex bolt, M12 washer, M12 lock washer and M12 hex nut.
3. Align fan assembly with uprights at desired height.
4. Secure to uprights with two M6 x 40 mm hex bolts and two M6 flange nuts.