ULINE H-6697 Shower Eyewash Station

Tool Needed

Strap Wrench

Assembly

Note: The unit is furnished with corrosion-resistant epoxy coating. Care must be taken to avoid damaging the finish during assembly. For best results, a strap wrench should be used.

Note: The use of a vice is recommended for proper tightening and alignment.

IMPORTANT! All threads are tapered pipe and require pipe joint compound or Teflon tape to assure a watertight connection. When securing with Teflon tape, wrap tape around each thread 10-12 times for optimal seal.

1. Unscrew the large shower connection pipe (1) from the elbow (2) and shower ball valve (3). Wrap Teflon tape around the threading and reassemble.
2. Unscrew the small shower connection pipe (4) from the shower ball valve (3). Wrap Teflon tape around the threading and reassemble.
3. Assemble the shower head (5) onto the elbow (2) and set assembled parts aside.
4. Unscrew the square head plug (6) from the top inlet tee (7). Wrap Teflon tape around the threading and reassemble.
   Note: If the top inlet tee (7) will be where the water source is supplied, screw the square head plug (6) into the side of the middle inlet tee (8) instead.
5. Wrap tape around the threading of the base support unit (9) and connect to the eyewash basin connection pipes (10).
6. Attach the eyewash basin (11) to the basin connection pipes (10).
7. Wrap tape around the threading of the middle pipe section (12) and connect to the basin connection pipes (10).
8. Connect the hose (13) to the ball valve and position for proper access by users.
9. Wrap tape around the threading of the top pipe section (14) and assemble to the top of the middle inlet tee (8).
10. Take the assembled shower connection pipe from steps 1-3, wrap with tape, and connect to the side of the top inlet tee (7) so that the shower head (5) is facing down for proper use.
11. Attach the pull handle (15) to the arm of the ball valve (3).
12. Connect the water line to the top inlet tee (7) or middle inlet tee (8). The square head plug (6) should be in the tee that does not have the water supply.
13. Secure the unit to the floor and run water through the pipes to flush out any impurities and test for proper operation.

Diagram Description (Assembly Steps): The diagrams illustrate the assembly process. They show numbered parts including a shower head (5), elbow (2), ball valve (3), connection pipes (1, 4, 12, 14), pull rod (part of 15), eyewash basin (11), hose (13), inlet tees (7, 8), and a base support unit (9). The diagrams indicate how these components connect using threaded fittings, with part numbers labeled in circles.

Dimensions and Specifications

This unit complies with the requirements of ANSI Z358.1.

Diagram Description (Overall Unit - Front View): This diagram shows the assembled shower eyewash station from the front. Key features include the shower head at the top, a pull rod, twin spray heads, an eyewash basin, and a push handle. The overall height is approximately 92 inches. The height to the shower head is approximately 86 inches. The eyewash basin is mounted at a height of approximately 44 inches. The basin itself measures approximately 16 x 10.5 inches. A detail view shows 5/16" mounting slots for securing the unit to the floor.

Diagram Description (Overall Unit - Side View): This diagram shows the assembled shower eyewash station from the side, illustrating its profile and dimensions. The shower head assembly extends outwards. Key dimensions noted are: overall height approximately 92 inches, height to the shower head approximately 28 1/3 inches, shower arm reach approximately 24 inches, and height to the eyewash basin approximately 44 inches. The unit features galvanized steel pipe and fittings. Water inlet connections are labeled as 1 1/4" NPT inlet (at the top and middle sections of the vertical pipe), and the outlet is labeled as 1 1/4" NPT outlet (at the base).

Contact Information

For inquiries, contact ULINE at 1-800-295-5510 or visit uline.com.