VonHaus Rustic Console Table with Drawer

⚠️ WARNING ⚠️

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE

IMPORTANT SAFETY INSTRUCTIONS

• Do not use the Rustic Console Table with Drawer for any purpose other than that for which it is designed.
• This product is not a toy. Children should be supervised to ensure they do not play with the product.
• ? CAUTION: The assembly pack contains small parts which pose a choking hazard to children and pets. Keep children and pets clear at all times during assembly.
• Locate the Rustic Console Table with Drawer in a suitable area where it will not be an obstruction.
• Place on solid, even ground.
• This Rustic Console Table with Drawer is water resistant but not waterproof; any prolonged contact with water can cause the wood to warp or damage the finish.
• ? CAUTION: Do not place hot drinks directly onto the furniture.
• ⚠️ WARNING! Never stand on, or rest on the product as this can cause damage or injury.
• Do not overload the product as this may result in damage to the product or personal injury.
• Do not exceed maximum weight capacity of 10kg.
• Do not clean the product with any abrasive chemicals, solvents, and detergents as this can damage the surface.
• Periodically check the fittings and secure as necessary (every 3 months or as required). Re-tighten the fittings 1 week after first assembly.
• Take care not to over tighten any fixings as this could damage the product.
• Always assemble near to the area to be installed/placed.
• Ensure you have sufficient space to assemble the product.
• ? CAUTION: Do not use any power tools to assemble the product as this could cause damage to fixings and panels.

Anti-Tip Safety Strap Information

It is recommended that furniture items above 75cm in height should be secured to a wall to prevent accidental tipping.

Securing the Anti-Tip Strap (Not Supplied)

1. Attach the Anti-Tip Strap to the back of the unit, secure into place.
2. Place the unit against the wall you wish to be located and mark the wall where the tip strap will be attached.
3. ? NOTE: It is recommended to attach the tip strap a little lower than the top and depending on location (centre or either side).
4. Use the appropriate wall fitting to secure into place.

?️ TOOLS REQUIRED: [Not Supplied]

HARDWARE

COMPONENTS

The following numbered parts are included in the package:

1. Left Frame
2. Right Frame
3. Back Panel
4. Shelf
5. Drawer Runners (x2)
6. Drawer Side Panel (Left)
7. Drawer Side Panel (Right)
8. Drawer Back Panel
9. Drawer Front Panel
10. Drawer Base Panel
11. Drawer Support Rail
12. Drawer Support Rail
13. Drawer Front Support
14. Drawer Back Support
15. Drawer Base Panel
16. Drawer Front Panel

ASSEMBLY

STEP 1

Attach the two side frames (parts 1 and 2) to the bottom support rail (part 3). Use 6x screws (A) and 6x dowels (U) for one frame, and 6x screws (B) for the other frame. The diagram shows screws being inserted into pre-drilled holes.

STEP 2

Attach the second side frame (part 1) to the bottom support rail (part 3). Use 6x screws (A) and 6x dowels (U) for one frame, and 6x screws (B) for the other frame. The diagram shows screws being inserted into pre-drilled holes.

STEP 3

Place the shelf (part 4) between the side frames. Secure it using 4x screws (C) through the pre-drilled holes on the side frames into the shelf.

STEP 4

Attach the drawer runner brackets (parts E and F) to the side frames. Part E attaches to the left frame, and part F attaches to the right frame. Use 2x screws (D) for each bracket.

STEP 5

Assemble the drawer box. Attach the drawer side panels (parts 6 and 7) to the drawer back panel (part 8). Use 4x screws (G) for each side panel. Then attach the drawer front panel (part 9) to the side panels using 4x screws (H) and 4x screws (G).

STEP 6

Attach the drawer top panel (part 9) to the assembled drawer sides and back. Use 4x screws (J) inserted from the top.

STEP 7

Slide the drawer base panel (part 10) into the grooves on the drawer side and back panels. Secure the drawer base panel by attaching the main frame parts (1, 2, 3, 4, 6, 7, 8) together. Use 4x screws (A) and 4x screws (C).

STEP 8

Slide the drawer base panel (part 10) into the grooves on the drawer side and back panels. The diagram shows the drawer base sliding into place from the front.

STEP 9

Attach the drawer front panel (part 9) to the assembled drawer box. Use 4x screws (G) and 4x screws (K) inserted from the inside of the drawer sides and back.

STEP 10

Attach the drawer support rails (parts 11 and 12) to the inside of the main console frame. Use 4x screws (M) and 4x screws (L) for each rail. Attach the drawer front support (part 13) and drawer back support (part 14) to the top of the console frame using 1x screw (O) and 1x screw (N) respectively.

STEP 11

Assemble the drawer base. Attach the drawer support rails (parts 11 and 12) to the drawer base panel (part 15). Use 6x screws (P). Attach the drawer front panel (part 9) to the assembled drawer base using 2x screws (R). Attach the drawer back panel (part 16) to the drawer base using 1x screw (Q).

STEP 12

Slide the drawer base panel (part 15) into the grooves on the drawer side panels (parts 6 and 7). Attach the drawer front panel (part 9) to the drawer side panels using 5x screws (K). Attach the drawer back panel (part 8) to the drawer side panels using 5x screws (K).

STEP 13

Insert the assembled drawer into the console frame. The diagram shows the drawer sliding into place. Attach the drawer runners (part 5) to the sides of the drawer using 1x screw (S) and 1x screw (T) for each runner.

STEP 14

Attach the drawer front panel (part 9) to the drawer box. Use 4x screws (D) inserted from the inside of the drawer side panels. The diagram shows the drawer front being attached.

CLEANING

A weekly dust will help shift the filmy layer of airborne deposits that build up over time and can scratch the surface of your furniture.

Dampen a clean, dry cloth (non-scratching and preferably microfibre) with water and gently wipe the surface. The moisture will collect the dust and prevent any flyaway dust particles.

? CAUTION: Avoid using any abrasive cleaning solvents on the (Rustic Console Table with Drawer) as this may damage the surface.

CUSTOMER SERVICE

If you are having difficulty using your product and require support, please contact hello@domu.co.uk

DISPOSAL INFORMATION

Please recycle where facilities exist. Check with your local authority for recycling advice.

WARRANTY

To register your product and find out if you qualify for a free extended warranty please go to www.Vonhaus.com/warranty.

Please retain a proof of purchase receipt or statement as proof of the purchase date.

The warranty only applies if the product is used solely in the manner indicated in the Warnings page of this manual, and all other instructions have been followed accurately. Any abuse of the product or the manner in which it is used will invalidate the warranty.

Returned goods will not be accepted unless repackaged in its original packaging and accompanied by a relevant and completed returns form. This does not affect your statutory rights.

No rights are given under this warranty to a person acquiring the appliance second-hand or for commercial or communal use.

COPYRIGHT

All material in this instruction manual are copyrighted by DOMU Brands.

Any unauthorised use may violate worldwide copyright, trademark, and other laws.