HILLESJÖN Kitchen Sink Installation Guide
Overview
This document provides installation instructions for the IKEA HILLESJÖN kitchen sink. The sink unit is made of stainless steel and complies with requirements for durability and cleanability.
Important Notes:
- Silicone sealant is not included. It is essential to seal cut edges with silicone to prevent water from penetrating the countertop in case of leakage.
- Screws or mounting fittings for securing the sink to the countertop are not included. Choose fittings suitable for your countertop material and ensure they have sufficient holding power. Consult a specialized dealer if uncertain.
Tools and Components
Tools Required:
- Drill with Ø 1/8" (3 mm) drill bit (4x)
- Drill with Ø 5/16" (8 mm) drill bit (4x)
- Jigsaw
- Measuring tape and pencil
- Silicone sealant (not included)
- Appropriate screws and mounting fittings (not included)
Included Components (Illustrative):
The package typically includes the sink unit (available in double bowl or 1.5 bowl configurations) and water trap components. Mounting brackets and clips are also provided.
- Sink Unit (Double Bowl or 1.5 Bowl with Drainer)
- Water Trap Assembly Components (e.g., part numbers 148966, 148962)
- Mounting Brackets (e.g., 10x, part 110385; 10x, part 109184)
- Adhesive strips for mounting (9x or 12x)
Installation Steps
Step 1: Prepare the Countertop
Marking the Cut-out: Place the sink upside down on the countertop. Use the sink itself or provided template pieces to trace the outline for the cut-out. Ensure correct positioning relative to the edges of the countertop. Specific measurements are provided in diagrams, for example:
- For one configuration, mark 55 mm (2 1/8") from the front edge and 65 mm (2 9/16") from the side edge.
- For another configuration, mark 65 mm (2 1/2") from the front edge and 65 mm (2 1/2") from the side edge.
Cutting the Opening: Drill pilot holes (Ø 1/8" or 3 mm, 4x) at the corners inside the marked cut-out area. Use a jigsaw to carefully cut along the traced lines. An offset of approximately 10 mm (3/8") from the inner line might be needed for the final cut, depending on the sink model.
Sealing Cut Edges: Apply a continuous bead of silicone sealant along all cut edges of the countertop opening. This is crucial to prevent water damage.
Step 2: Install the Sink
Positioning: Carefully lower the sink into the prepared opening in the countertop. Ensure it fits snugly and is correctly aligned.
Securing the Sink: Attach the provided mounting brackets to the underside of the sink. Use the adhesive strips (9x or 12x) to help position the sink. Then, from underneath the countertop, use the mounting clips (e.g., part 110385 and 109184) to secure the sink to the countertop. Tighten the clips evenly, typically to a depth of 28-40 mm (1 1/8" - 1 5/8") from the edge of the countertop.
Diagrams show the placement of clips and the tightening process.
Step 3: Install Water Trap and Faucet
Water Trap Assembly: Assemble the water trap components as shown in the diagrams (e.g., part numbers 148966, 148962). Connect the assembled water trap to the sink's drain outlets.
Faucet Installation: Install your mixer tap (faucet) according to its specific installation instructions. Ensure there is adequate clearance, for example, a minimum of 65 mm (2 9/16") from the sink edge to the faucet base.
Diagrams illustrate the water trap assembly and connection, and the faucet placement with minimum clearance.
Product Information
The HILLESJÖN kitchen sink is constructed from durable and easy-to-clean stainless steel, meeting all relevant requirements.
Final Checks and Support
Ensure all connections are secure and watertight. If you encounter any difficulties or have questions regarding installation, please consult your local specialized dealer or IKEA customer support.
