Drone Air Racer

SHARPER IMAGE

Getting to Know Your Drone

PLEASE READ ALL WARNINGS AND INSTRUCTIONS PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS IMPORTANT INFORMATION ABOUT YOUR DRONE.

1. PREPARE FOR FLIGHT

2. PAIR YOUR DRONE

Before each flight pair the remote with the drone:

3. REMOTE CONTROL OVERVIEW

Practice flying your drone below 10 feet and at low speeds until comfortable with all controls to avoid unnecessary damage or injury.

To cut power to drone, move left joystick to down position.

QUESTIONS OR CONCERNS?

PLEASE GIVE US A CALL ... WE'RE HERE TO HELP

CUSTOMER SUPPORT

(800) 374-2744

Before calling please locate the 10-digit code printed on the back of your remote

Sharper Image® name and logo are registered trademarks. Distributed by and 2022 MerchSource, LLC. Irvine, CA 92618. All rights reserved.

Distributed by MerchSource, LLC, Irvine, CA 92618.

For technical support, please visit www.merchsource.com or call 1-800-374-2744.

The artwork and design of this manual are protected by US copyright law and may not be reproduced, distributed, displayed, published or used for any purpose without prior written permission. It is not permitted to alter, remove or reproduce any trademarks or copyright notice from this manual.

Printed in China.

ADULT ASSEMBLY, CHARGING, AND BATTERY INSTALLATION IS REQUIRED. ADULT SUPERVISION IS REQUIRED.

WARNING: CHOKING HAZARD - Small Parts. Not for Children under 3 years.

KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE.

Due to continuous product improvements, the picture on the manual may differ slightly from the actual product.

PATENT PENDING

Model Number: 1015423

INTRODUCTION

Congratulations on your purchase of the Rechargeable 2.4 GHz Fly+Drive Drone. Get ready to soar to new heights. Master the art of drone flying with remote control maneuverability. This lightweight drone will provide hours of fun.

SPECIFICATIONS

READ ALL WARNINGS AND PRECAUTIONS BEFORE USE

SAFETY WARNINGS

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Fly-aways are the responsibility of the individual pilot and will not be replaced by the manufacturer.

This drone weighs 0.242lbs (110g). As of December 21, 2015, the Federal Aviation Administration (FAA) only requires registration on unmanned aircrafts weighing more than .55 lbs. Visit www.faa.gov/uas/registration/ for more information. Although the FAA does not require this drone to be registered, ongoing compliance with federal, state, and local laws is an owner's sole responsibility. Always fly safely and respect the privacy of others.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Printed in China.

TROUBLESHOOTING:

When remote switch is turned on, the remote light does not illuminate:

  1. Check that batteries in the remote are installed correctly OR
  2. Replace with new batteries.

When remote LED come dim or the control sensitivity is weak:

  1. Remote batteries are low.
  2. Replace them with new batteries.

Drone and remote properly pair, but the drone will not lift-off or the drone LEDs flash during the flying:

  1. Drone Li-Po needs charging.
  2. Use charging cable to connect the drone to power source.

After trimming the drone, the drone flight is very unstable and cannot fly properly:

  1. One or more blades are most likely damaged.
  2. Turn off the drone and remote.
  3. Replace with the proper number replacement blade and try flying again.

After impact, the drone is unstable:

  1. Land the drone on the ground and propellers are stopped. Press and hold Land button for 3s to calibrate the gyro.
  2. If the above does not resolve the issue, reboot the drone and controller and pair again.

Remote Controller and Drone can not be paired:

  1. Check Point: Remote Controller must be close to Drone.
  2. Do not exceed 4 meters.

Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set.

CONTENTS

REMOTE BATTERY INFORMATION

  1. Unscrew the remote battery door using a Philips head screwdriver (not included).
  2. Install 4 "AA" batteries as shown in the diagram above.
  3. Replace and close battery compartment.

LITHIUM-POLYMER BATTERY WARNING

There is a risk of fire and personal injury if Li-Po battery is punctured, damaged or misused.

KEEP THIS INSTRUCTION MANUAL FOR REFERENCE

BATTERY WARNING - ALKALINE (AA)

Printed in China.

CHARGING BATTERY

Note: The charging light on the drone will light up when it is charging and turn off when fully charged. Charge time is approximately 120 minutes.

  1. Turn off the drone before charging.
  2. Connect the Battery Charger Cable to the port found on the rear of the drone.
  3. Connect USB connector to the power source.

Connect the Charge Cable to the Drone

Replacing Propellers

  1. Pull firmly to remove broken propeller. Replace with a new one. Push firmly and carefully.
  2. Replace propellers by following the diagram on the right.
  3. Each blade spins differently. Blade A1 turns clockwise and Blade B1 turns counter clockwise.

A1

B1

B1

A1

Printed in China.

REMOTE OVERVIEW

ON/OFF Button

Align

Left Spin Trim

Throttle Joystick: Increases or decreases drone elevation left/right controls spin

Backward Adjustment

Forward Adjustment

ALIGN

LAND

TRIM

TRIM

LED Light

Auto Land

Right Spin Trim

Right Adjustment

Left Adjustment

Printed in China.

OPERATING DRONE

Step 1 – Pre-Flight Checklist

Step 2 – Choosing a location

Step 3 – Driving Mode

  1. Turn the drone and remote on then place the drone on a hard flat surface and allow to sit for 4 seconds.
  2. Slowly and carefully press the Throttle Joystick up. Drone will begin to elevate. You can compensate for some of the drone's drifting by using the Multi Directional Button or by following step 5. You may need to practice this step several times before successfully getting drone into the air.

Step 4 – Lift Off

  1. Bring the car to a stop.

Pair remote to drone:

  1. Bring the Throttle all the way up then bring it all the way down, remote will beep once paired.
  2. Use the Multi Directional Joystick to move forwards, backwards or turn left and right.

Note: After pair is successful, keep the throttle down all the way, to enter driving mode. After pair is successful, you can enter flying mode by following step 4 (shown below)

Printed in China.

OPERATING DRONE (Cont.)

Step 5 – Operating Drone in Flight

Follow this step if your drone begins to drift while take off or during flight.

SPIN TRIM

Use the Throttle Joystick to increase or decrease your elevation.

Use the Multi Directional Joystick to move forwards, backwards or turn left and right.

Step 6 – Landing Drone

Lower drone to 20 feet or less then press the Auto Land button. Use the Multi Directional Joystick to maneuver drone. Press the Auto Land Button a second time to deactivate auto land.

Step 7 – Retrieving Drone

  1. Turn off your remote by rotating the ON/OFF Button. This will stop you from accidentally turning the propellers on.
  2. Make sure the propellers have stopped spinning then pick up your drone.

Note: You will need to pair your drone again before your next flight.

Align

Press the Align Button to turn Align mode ON and then again to turn off. The button will be light on when in Align mode. In this mode, the drone will always move in the direction you press the Multi Directional Button no matter which way the drone faces.

Turn off your remote by rotating the ON/OFF Button.

Tips

On a full charge, the drone will fly for approximately 4 minutes. The LED indicators will flash indicating that the drone needs to land.

You can continue driving the drone in car mode for approximately 2 minutes before recharging the drone.

Printed in China.

Models: HB2023N, 2A4XIHB2023N, 087-05-5435, Drone Air Racer, 087-05-5435 Drone Air Racer, Air Racer

File Info : application/pdf, 8 Pages, 736.98KB

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=6740739

References

Adobe Illustrator 26.5 (Macintosh) Adobe PDF library 16.07

Related Documents

Preview Sharper Image Video Streaming Drone User Manual - Setup, Operation, and Troubleshooting
Comprehensive user manual for the Sharper Image Video Streaming Drone. Learn how to set up, charge, pair, operate, and troubleshoot your drone for optimal flight and video streaming.
Preview Sharper Image Drone Aero Stunt LED: Quick Start Guide & Troubleshooting
Learn how to operate, perform stunts, and troubleshoot your Sharper Image Drone Aero Stunt LED with this comprehensive quick start guide. Includes pre-flight checks, pairing instructions, charging details, and safety warnings.
Preview Drone Aero Stunt LED User Manual and Operating Guide
Comprehensive guide for the Drone Aero Stunt LED, covering pre-flight checks, operation, stunt modes, troubleshooting, and safety warnings. Learn how to pair, fly, and maintain your drone.
Preview Sharper Image Thunderbolt Jet X-2 Drone Operating Manual
User manual for the Sharper Image Thunderbolt Jet X-2 drone, covering setup, operation, advanced features, safety guidelines, and troubleshooting.
Preview Sharper Image Lighted Drone Owner's Manual - Item 206083
Comprehensive owner's manual for the Sharper Image Lighted Drone (Item No. 206083), covering features, specifications, battery charging, transmitter setup, drone pairing, flight controls, stunt flips, trimming, calibration, headless mode, auto hover, FCC compliance, and warranty information.
Preview Sharper Image 1014291 Drone Aero Stunt LED Helicopter User Manual
User manual for the Sharper Image 1014291 Drone Aero Stunt LED Helicopter, providing detailed instructions on operation, safety, charging, pairing, and troubleshooting.
Preview Sharper Image Halo Drone User Manual and Safety Guide
This user manual provides detailed instructions for operating the Sharper Image Halo Drone (Model 1019049). It covers setup, pairing, flight controls, stunt maneuvers, safety precautions, battery handling, and FCC compliance.
Preview Sharper Image DX-2 Stunt Drone Rechargeable 2.4GHz User Manual
User manual for the Sharper Image DX-2 Stunt Drone, a rechargeable 2.4GHz remote-controlled drone. Includes setup, operation, safety warnings, and troubleshooting.