Eufy RoboVac X8 Pro

Table of Contents

• About Your RoboVac
• Using Your RoboVac
• Cleaning and Maintenance
• Troubleshooting
• Specifications
• Customer Service

About Your RoboVac

What's in the Box

The package includes:

• RoboVac
• Mopping Module
• Cleaning Tool
• Owner's Manual, Quick Start Guide, and Other Documents
• Charging Base (T2266 only)
• Power Adapter (T2266 only)
• Waterproof Pad (T2266 only)
• Self-Empty Station (T2276 only)
• Power Cord (T2276 only)
• Waterproof Pad (T2276 only)

RoboVac Anatomy

A. Front: Features Recharge button, Auto cleaning Start/Pause button, Spot cleaning button, Dust box, Top cover, Wi-Fi indicator, and Laser distance sensor (LDS).

B. Side: Includes Reset button, Filter assembly, Charging contact pins, Water tank release button, Water inlet, Mopping module, Bumper, and Ventilation holes.

C. Bottom: Contains Charging contact pins, Side brush, Anti-drop sensors, Wheels, Rolling brush, and Brush guard.

D. Charging Base (T2266 only): Includes Status light, Wire slot exit, Power socket, Charging contact pins, and Power cord storage compartment.

E. Self-Empty Station (T2276 only): Features Disposable dust bag, Power socket, LED indicator, Infrared sensor, and Charging contact pins.

F. Mopping Module: Includes Washable cleaning cloth and Cloth attachment area.

LED Indication

Important Tips Before Use

• Remove power cords and small objects from the floor.
• Fold tasseled edges of rugs underneath to prevent tangling. Avoid cleaning high-pile rugs or rugs thicker than 1.02 in / 26 mm.
• Place physical barriers or set a “No-Go” zone via the eufy Clean app in front of fireplaces and certain areas (e.g., air vents) that may cause damage to RoboVac.
• Avoid vacuuming large amounts of water.
• Remove objects less than 0.75 in / 19 mm in height that RoboVac may climb on.
• Anti-drop sensors prevent RoboVac from tumbling down stairs. Ensure sensors are clean. Place physical barriers or set a “No-Go” zone to block off areas where RoboVac may fall.

Using Your RoboVac

Preparation

1. Remove the foam blocks beside the bumper before use.
2. Install the Self-Empty Station / Charging Base against a wall on a hard, level surface. Do not place it on carpets.
3. Ensure there is 1.6 ft / 0.5 m clearance on the left and right sides, and 4.9 ft / 1.5 m clearance in front of the Self-Empty Station / Charging Base.
4. Connect the power cord to the Self-Empty Station / Charging Base and a wall outlet. The LED indicator on the base will be solid white when connected to AC power. Keep the base plugged in.

Charge Your RoboVac

• Ensure the power cord is connected to a power outlet.
• Recharge at least once every 6 months to preserve battery lifespan.
• RoboVac returns to the Self-Empty Station / Charging Base automatically at the end of a cleaning cycle or when its battery is low.
• For T2276: RoboVac automatically empties the dust box when returning to the Self-Empty Station if cleaning lasted over 15 minutes. Ensure the dust bag is properly installed.
• Method 1: Attach RoboVac to the Self-Empty Station / Charging Base by aligning its charging pins.
• Method 2: Press the button on the main unit or tap the icon in the eufy Clean app to send RoboVac to the Self-Empty Station / Charging Base.

Auto Recharge and Resume

RoboVac automatically returns to the Self-Empty Station / Charging Base to recharge when:

• Cleaning is finished.
• Cleaning is not complete and the battery level is low. RoboVac resumes cleaning after recharging to 80% battery capacity.

Note: Do not move the Self-Empty Station / Charging Base during cleaning. If RoboVac fails to return, manually attach it. If the base is moved, start cleaning from the new location.

Power On / Off

Press and hold the power button for 3 seconds to power RoboVac on or off.

Use Your RoboVac with the eufy Clean App

Download the eufy Clean app from the App Store or Google Play. Create an account, tap the "+" icon to add RoboVac, and follow the in-app instructions to set up the Wi-Fi connection.

The app allows you to:

• Select cleaning at desired suction levels.
• Schedule cleaning.
• View the cleaning map.
• Set up “No-Go” zones.
• Check network connection status.
• Access additional features.

Wi-Fi Indicator Status:

• Slowly flashing blue: Waiting for connection.
• Rapidly flashing blue: Connecting with your wireless router.
• Solid blue: Connected with your wireless router.

Reset the Wi-Fi Connection

Press and hold the Wi-Fi button and the power button simultaneously for 5 seconds until you hear a voice prompt. The Wi-Fi status light will slowly flash blue, indicating the connection has been reset.

Schedule Cleaning

Use the eufy Clean app to schedule cleaning at specific times, customizing schedules from Sunday to Saturday.

Auto-Cleaning Mode

RoboVac automatically determines its cleaning route, cleaning edges first, then following a Z-shaped path. It returns to the Self-Empty Station / Charging Base upon completion.

Press the Auto cleaning button to start cleaning. Press again to pause.

Select a Cleaning Mode

Press the Auto cleaning button to start cleaning in Auto cleaning mode. Press the button again to pause.

Select a Suction Power Level

In the eufy Clean app, select suction power levels: Quiet, Standard (Default), Turbo, and Max.

Select BoostIQ™ Feature

Enable the BoostIQ™ feature in the eufy Clean app. RoboVac automatically increases suction power when stronger power is needed, ideal for thicker carpets and tough messes. This may reduce cleaning time but increase noise.

Use the Mopping System

1. Peel off stickers and install the waterproof pad under the Self-Empty Station / Charging Base.
2. Remove the water tank, fill it with water, and close the cover. Do not add cleaning formula.
3. Install the water tank back into RoboVac.
4. Remove the mopping cloth from the mopping module.
5. Wet the mopping cloth, wring out excess water, and attach it firmly to the mopping module.
6. Install the mopping module at the bottom of RoboVac until it clicks.
7. Start cleaning. RoboVac will vacuum and mop. Adjust water levels via the eufy Clean app.
8. After cleaning, remove the water tank, empty remaining water, and clean the mopping cloth.

Note: Do not install the mopping module when cleaning rugs or upholsteries to prevent RoboVac from getting stuck or dampening fabrics.

Use RoboVac with Amazon Alexa / The Google Assistant

Control RoboVac with your voice using Amazon Alexa or Google Assistant. Ensure RoboVac is connected to the eufy Clean app and you have the respective smart home app installed and an account set up.

Follow the instructions in the eufy Clean app under "Smart Integrations" to complete the setup.

Set Up Virtual Wall (Available on the App Only)

Use the eufy Clean app to set up “No-Go Zones”, “No-Mop Zones”, or “Virtual Walls” as restricted areas. This feature is for dividing cleaning zones, not for isolating hazardous areas.

• No-Go Zone: RoboVac will not enter the zone to vacuum.
• Virtual Wall: RoboVac will not cross the virtual wall.
• No-Mop Zone: RoboVac will not enter the zone to mop.

Note: RoboVac must perform an initial cleaning run to create a floor plan for virtual walls. Moving the device or changing the environment may require rebuilding the virtual wall.

Cleaning and Maintenance

Recommended Cleaning and Replacement Frequency

Clean the Dust Box and Filter

1. Open the top cover and remove the dust box.
2. Press the release button to open and empty the dust box.
3. Remove the filter assembly.
4. Rinse the dust box and filter thoroughly with water. Do not use a brush, hot water, or detergent to clean the filter.
5. Air-dry the dust box and filter assembly completely before next use.
6. Place the filter assembly back into the dust box.
7. Push the dust box back into the main unit.

Clean the Rolling Brush

1. Pull on the release tabs to unlock the brush guard.
2. Lift the rolling brush to remove. Clean the rolling brush with a cleaning tool.
3. Reinstall the rolling brush by inserting the fixed protruding end first.
4. Press down to snap the brush guard into place.

Clean the Side Brush

1. Remove the side brush.
2. Unwind and pull off any hair or substances wrapped between the main unit and the side brush.
3. Clean the side brush with water.

Clean the Swivel Wheel

Hair or dust particles can easily get entangled in the swivel wheel. Clean it periodically.

1. Pull out the swivel wheel with a tool (e.g., screwdriver).
2. Clean any hair or debris wrapped around the wheel or inside the wheel cavity.
3. Reinstall the wheel and push it in until it clicks into place. Do not clean the swivel wheel with water.

Clean the Sensors and Charging Pins

Clean the sensors and charging contact pins regularly using a cloth or cleaning brush.

Clean the Mopping Cloth and Water Tank

1. After each use, remove the mopping cloth and water tank.
2. Rinse the mopping cloth and water tank thoroughly with water.
3. Air-dry the mopping cloth completely to prevent mildew or unpleasant smells.

Replace the Dust Bag (T2276 Only)

1. Lift open the top cover.
2. Pull the release button to position, then pull up the handle to remove the dust bag.
3. Discard the used dust bag.
4. Install the new dust bag by sliding its paper board into the slot until a click is heard.

Troubleshooting

For further troubleshooting information, visit support.eufy.com, use the eufy Clean app, or contact support@eufy.com.

Specifications

Customer Service

Contact Us

• Email: support@eufy.com
• Website: www.eufy.com
• Phone (US/CA): +1 (800) 994 3056
• Phone (UK): +44 (0) 1604 936200
• Phone (DE): +49 (0) 69 9579 7960
• Phone (JP): +81 03 4455 7823

For more support phone numbers, please visit: support.eufylife.com/s/phonecontactus

For tutorial videos, FAQs, manuals, and more information, please visit: support.eufy.com

Follow us:

@EufyOfficial @EufyOfficial @EufyOfficial @EufyOfficial