SolidForce NVMe/SATA Aluminium Enclosure Lite S1204B

Product Overview

The SolidForce NVMe/SATA Aluminium Enclosure Lite supports USB SuperSpeed 10Gbps and is compatible with M+B Key M.2 SSDs.

Key Features:

• A. USB-C port: The primary connection port for your computer.
• B. Blue LED indicator: Provides status information.
  • Solid blue: The enclosure is connected and recognized by the system.
  • Twinkling blue: Data is being read from or written to the SSD.
  • Twinkling blue (1 second on, 3 seconds off): The enclosure is in sleep mode.

How to Use

I. Install the Aluminium Heat Exchanger

This step ensures efficient heat dissipation for the M.2 SSD.

1. Carefully remove the protective surface layer from both the Aluminium Heat Exchanger and the Silicone Thermal Pad.
2. Apply the Silicone Thermal Pad onto the surface of the M.2 SSD.
3. Place the Aluminium Heat Exchanger onto the thermal pad, ensuring it is sandwiched between the SSD and the heat exchanger for optimal thermal contact.

Visual Description: A diagram illustrates the thermal setup, showing an M.2 SSD with a Silicone Thermal Pad applied to its surface, and an Aluminium Heat Exchanger positioned on top of the thermal pad.

II. 80mm M.2 SSD Installation

Instructions for installing an 80mm length M.2 SSD into the enclosure.

1. Press the lock button (labeled 'A' in diagrams) on the enclosure to release the internal assembly.
2. Gently pull out the mainboard assembly from the enclosure.
3. Insert the M.2 SSD diagonally downwards into the PCIe/NVMe slot on the mainboard. Ensure it is seated correctly.
4. Gently press down on the M.2 SSD with your fingers to snap it into the plastic retaining clip (labeled 'B' in diagrams). This secures the SSD. To disassemble, push the clip outward in the opposite direction to release the SSD.

Visual Description: A diagram shows the M.2 SSD being inserted into the slot on the mainboard. Label 'A' points to the lock button used to release the internal assembly. Label 'B' points to the plastic clip that secures the M.2 SSD in place.

III. 42/60mm M.2 SSD Installation

Instructions for installing 42mm or 60mm length M.2 SSDs into the enclosure.

1. With the M.2 SSD inserted into the enclosure's inner tray, use your finger to press at point 'C' on the tray.
2. Simultaneously, insert the M.2 SSD into the securing buckle 'D' located on the tray.
3. From underneath the tray, lightly press at point 'D' to ensure the SSD card is fully secured, indicated by a click sound. To release the SSD, pull the buckle outward from the top.

Visual Description: A diagram shows the inner tray of the enclosure with an M.2 SSD inserted. Point 'C' indicates a location on the tray to press, which engages the securing buckle 'D' that holds the SSD firmly in place.

Package Contents

• SolidForce NVMe/SATA Aluminium Enclosure Lite
• Operating Instructions

Safety Notes

• Do not attempt to service or repair the product yourself. All service work should be performed by qualified experts.
• Do not open the device or continue to operate it if it becomes damaged.
• Do not modify the product in any way. Doing so will void the warranty.
• Do not drop the product and do not expose it to any major shocks or impacts.
• Keep this product, like all electrical products, out of the reach of children!

Warranty Disclaimer

UNITEK assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the operating instructions and/or safety notes.

Technical Data

Compatibility

Connection: USB-C/USB-A port

System Requirements

• Windows 10 / 8 / 7
• Mac OS 10.8 or higher

USB Specification

USB 3.1 Gen 2

Important Notes

• The M.2 SSD adapter must not be unplugged from the PC during data transfer under any circumstances. Doing so may result in data loss.
• Upon connection, your PC/notebook's operating system will initialize the M.2 SSD. This process may take up to one minute. If the SSD is already partitioned and contains data, you will be able to access it.
• New or unpartitioned SSDs require partitioning and formatting after initialization. Refer to your computer/notebook's operating system manual for the necessary steps.
• This enclosure features an M Key interface, which is part of the PCIe/NVMe protocol channel. When installing an SSD for this product, please ensure you check compatibility.
• Install the SSD as gently as possible to avoid scratching components on the printed circuit board. Be mindful of static electricity when installing SSDs. For safety, it is recommended to disconnect all power sources before proceeding with the installation.
• Before attempting to disassemble the enclosure, it is recommended to save all data properly on your SSD to prevent any loss.
• As Windows 10 and later, along with Mac OS, offer the best compatibility with NVMe, this product is recommended for optimal transmission performance on these operating systems.

Service and Support

For further support information, please visit: www.unitek-products.com

Email support: support@unitek-products.com