WINCO Stainless Steel Water Boiler

Specifications

Important Information Before Operation

BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS.

Congratulations on your purchase of this WINCO® commercial equipment. WINCO takes pride in the quality of its products. When used as intended, and with proper care and maintenance, you will experience years of reliable operation from this equipment. To ensure best results, it is important that you read and follow the instructions in this manual carefully. It's important to save these instructions for future reference.

Form No. EWB-Series Manual - 01/21

Important For Future Reference

Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or parts, this information is required.

Introduction

Congratulations on the purchase of the WINCO® equipment. Please take time to carefully read through this manual to ensure the equipment is operated and maintained properly, to ensure the best possible performance from the product for many years.

WINCO will not accept liability for the following if:

• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the equipment.
• Non-original spare parts are used.
• The equipment has not been handled and cleaned correctly.
• There is any use damage to the unit.

Immediately Inspect for Shipping Damage

All containers should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent or concealed, a claim must be made with the delivering carrier.

A. Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the necessary forms.

B. If concealed damage or loss is not apparent until after equipment is uncrated, a request for inspection must be made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to keep all contents and packaging material.

Package Contents

All units come with an Operating Instruction Manual and the following:

• Water Boiler

WINCO® prides itself on quality and service, ensuring that at the time of packing, all products are supplied fully functional and free of damage. Should you find any damage as a result of freight, please contact your WINCO dealer immediately.

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN ENVIRONMENTALLY RESPONSIBLE MANNER.

1. Remove all packing materials and tape, as well as any protective plastic and cardboard, from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES ARE NEEDED.

Important Safeguards

To ensure safe installation and operation, please carefully read and understand the following statements. Unless the operator is adequately trained and supervised there is a possibility of serious injury. Owners of this equipment bear the responsibility to make certain that this equipment is used properly and safely, and to strictly follow all of the instructions contained in this manual and the requirements of local, state or federal law.

Owners should not permit anyone to touch this equipment unless they are over 18 years old, are adequately trained and supervised, and have read and understood this manual.

Owners should also ensure that no customers, visitors or other unauthorized personnel come in contact with this equipment. It is the responsibility of the owner and the operator to remain alert to any hazards posed by the function of this equipment.

If there is ever uncertainty about a particular task or the proper method of operating this equipment, ask an experienced supervisor or contact Winco® for assistance.

Warnings

This manual contains a number of precautions to follow to help promote safe use of this equipment.

? HOT WARNING: USE CAUTION WHEN TOUCHING THE UNIT.

AVERTISSEMENT: Ne touchez pas le liquide chaud ou les surfaces de chauffage lorsque l'appareil chauffe ou en fonctionnement.

Detailed Safeguards and Warnings

These instructions should be followed at all times. Failure to follow these instructions could result in injury to yourself and others.

TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:

1. Read this manual thoroughly before installation and operation. DO NOT proceed with installation and operation if you have any questions or do not understand anything in this manual. Contact your representative or the manufacturer first.
2. DO NOT touch any surfaces that may be hot.
3. Unplug from outlet when not in use prior to installing or removing parts and before cleaning. Allow for the device to cool first before handling.
4. To protect against the risk of electrical shock, do not immerse the appliance, cord or plug in water, or other liquids.

5. DO NOT operate this device or any other electrical equipment with a damaged cord or plug, or after the unit malfunctions, is dropped or damaged in any manner. Return to the nearest WINCO Authorized Service Center for examination, repair and/or adjustment.

6. The use of accessory attachments not recommended by WINCO may cause fire, electric shock or injury.

7. Not intended for outdoor installation.

8. DO NOT let the cord hang over the edge of a table or counter, or touch hot surfaces.

9. DO NOT place on / near a hot gas / electric burner, or heated oven.

10. This appliance should always be on a stable and steady countertop or table. Allow sufficient space around the cooking area. Never use the unit on/near low-heat-resistant materials (carpet, vinyl).

11. This appliance is not intended for use by individuals (including children) with reduced or impaired physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given proper supervision or instruction concerning the use of this appliance by a person responsible for their safety.

12. Any objects that are not intended for use with the appliance should not be in the unit.

13. Clean with caution – if a wet sponge or cloth is used to wipe spills on a hot cooking surface, exercise caution to avoid steam burns. NOTE: some cleaners may produce noxious fumes when applied to a hot surface.

14. Do not store any item on top of this unit when in operation.

15. Never place materials such as paper, cardboard, plastic, etc. on or under this unit.

16. Proper connections and power supply are essential for efficient performance.

17. If an extension cord power-supply is used:

• a. The marked electrical rating of the extension cord should be rated the same or greater than the electrical rating of the unit.
• b. The cord should be located so that it does not drape over the counter/tabletop and can not be damaged or moved unintentionally.

18. The units are wired to be used with a standard 120V or 220V/AC receptacles and may be plugged into any convenient outlet (refer to units serial plate).

19. The installation of the unit must conform to the NATIONAL ELECTRIC CODE, ALL LOCAL ELECTRIC CODES AND ORDINANCES, AND ALL THE LOCAL ELECTRICAL COMPANY RULES AND REGULATIONS. Additionally, we recommend a 4" spacing surrounding the unit in order to provide adequate ventilation.

Proper Grounding

This machine is provided with a three-pronged grounding plug ?. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician. DO NOT, under any circumstances, cut or remove the third ground prong from the power cord or use any adapter plug.

Cette machine est équipée d'une fiche à trois broches. La prise sur laquelle cette fiche est branchée doit être correctement mise à la terre. Si la prise n'est pas le type de mise à la terre, contactez avec un électricien. NE PAS, en aucun cas couper ou enlever la troisième broche de terre à partir du cordon d'alimentation ou utiliser un adaptateur.

USE A GROUNDED OUTLET
DO NOT ADD AN ADAPTOR TO THE PLUG

UTILISER UNE PRISE AVEC MISE À LA TERRE
NE PAS AJOUTER UN ADAPTATEUR SUR LA FICHE

Preparation

It is recommended to clean the Water Boiler before the first use. To clean and protect the urn, the manufacturer used food grade cleaning oil on the product.

1. Fill the Water Boiler to "MAX" level with water, boil, discard the water, and rinse. Repeat the procedure several times to remove any dust, residues, etc., from the Water Boiler.

Operation

1. Place Water Boiler on a flat leveled surface.
2. Remove locking lid by turning counterclockwise.
3. Fill Water Boiler with water up to the "MAX" indicator inside.
4. Plug the unit into 120V or 220V power source (as noted on serial tag) and turn ON. The heating indicator light will turn on and the water will start to heat up. This will continue until the unit automatically switches to its warming state.

⚠️ WARNING: DO NOT attempt to open the lid while the unit is operating to avoid the risk of burning due to the hot water.

5. Once warming indicator light turns ON, the water can now be dispensed. Use the faucet to dispense the water.

? HOT WARNING: Burn Hazard. When in operation, the appliance surfaces will be HOT! Please take extreme caution. USE CAUTION WHEN TOUCHING THE UNIT.

AVERTISSEMENT: Risque de brûlure. En fonctionnement, les surfaces de l'appareil seront CHAUDES! S'il vous plaît prendre une extrême prudence. Ne touchez pas le liquide chaud ou les surfaces de chauffage lorsque l'appareil chauffe ou en fonctionnement.

Cleaning, Care & Maintenance

To maintain the appearance and increase the service life, clean the water boiler daily.

Clean all surfaces before using the appliance. Also clean after each day's operation; however, the unit may require more frequent cleaning, depending on the volume of production.

• Switch power off and disconnect from the outlet before cleaning.
• Unplug the unit when not in operation.
• Allow unit to cool before attempting to clean.
• The interior of the water boiler should be cleaned periodically with warm, soapy water and soft cloth.
• The exterior of the unit may be cleaned by carefully wiping with a damp cloth.
• DO NOT immerse the unit in water.
• DO NOT clean with a pressure washer.

Safety Precautions

Before installing and operating this equipment be sure everyone involved in its operation are fully trained and aware of all precautions. Accidents and problems can result from a failure to follow fundamental rules and precautions.

• A WINCO® Approved Recommended Qualified Service Technician should carry out repairs if necessary. Do not remove any components or service panels on this product.
• Before handling, allow the equipment to cool after use.
• Before cleaning, switch off power and disconnect power cord from the outlet.
• Do not immerse unit in water or use hose to clean. Ne jamais immerger l'appareil dans l'eau ni utilisez un jet d'eau pour le nettoyer.
• If the power cord is damaged, it must be replaced by a WINCO® Approved Recommended Qualified Service Technician in order to avoid a hazard.

THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.

Troubleshooting

If your equipment unit does not operate, please check the following prior to placing a service call.

Thermo Shut Off Reset

1. Remove bottom cover plate.
2. Locate the thermo shut off switch and press to reset unit.

Service and Repair

THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.

NOTE

Parts protected by the manufacturer or its agent are not to be adjusted by the installer unless the installer is an authorized service agent.

If you have any questions or problems DO NOT send unit to WINCO® without first contacting our customer service department. See "Limited Warranty" section on page 10 for details.

Exploded View

MODEL: EWB-100A

The exploded view diagram shows the components of the WINCO EWB-100A water boiler. It displays the unit from top to bottom, with numbered parts indicated by arrows.

• 1. The lid assembly is at the top.
• 2. The handle assembly is attached to the body.
• 3. The water gauge assembly is mounted on the side of the boiler.
• 4. The faucet assembly is located at the lower front.
• 5. The 130°C thermal disk is shown near the bottom.
• 6. Rubber feet are at the base.
• 7. The 94°C thermal disk is also shown near the bottom.
• 8. Various screws, brackets, and internal components are depicted around the main body and base.
• 9. The power cord connects to the base.
• 10. Indicator lights (yellow and red) are visible on the control panel.
• 11. The switch with a rubber cover is part of the control panel.
• 12. A fuse is also indicated in the electrical components.

Parts List

Please contact factory for special order parts not listed.

Electrical Diagrams

The document includes electrical diagrams for two voltage configurations:

Models EWB-50A and EWB-100A (110/120V):

This diagram shows the power flow from the L (Line) and N (Neutral) terminals, connected through a power switch. The circuit includes a 94°C thermal disk, a heating element, a yellow indicator light, and a red indicator light. A fuse is also present in the circuit. The Ground connection is shown separately.

Model EWB-100A-I (220/240V):

This diagram illustrates a similar circuit for higher voltage. It includes a power switch, a 130°C thermal disk, a heating element, a yellow indicator light, and a red indicator light. A fuse is also included. The Ground connection is shown separately. The diagrams are intended for qualified electricians.

Limited Warranty

WINCO® warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subjected to normal use, is free from defects in material or workmanship for a period of 1 year. The labor warranty is one year from original installation or 18 months from actual factory shipment date, whichever date occurs first.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WINCO'S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT THAT PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.

IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR OTHERWISE.

This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees.

Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear, improper set up and use. Periodic maintenance is not covered.

This warranty is not in force until such time as a properly completed and digitally signed Installation/Warranty Registration has been received by WINCO within 30 days from the date of installation.

Limited Warranty (continued)

WARRANTY SERVICE

To initiate warranty service contact: EquipService@wincous.com or call: 973-295-3899

DO NOT send unit to WINCO® without first contacting our customer service department. Please provide or have the following information available:

• Model & Serial Number (located on the silver identification tag, on side or rear of unit)
• Date of Purchase
• Purchase Dealer
• Operator / Installation Contact Information
• Business Name & Business Address
• Contact Name & Contact Telephone Number

REGISTER ONLINE AT:

http://www.wincous.com

Proof of purchase is required to extend warranty more than 1 year from date of shipment from the factory.

THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. WINCO® NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.

Examples of items not covered under warranty, but not limited to just these items:

1. Natural disasters (ie: earthquakes, tornadoes, hurricanes, etc.), fire, water damage, burglary, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after-market parts.
5. Repairs made by anyone other than a WINCO® designated service provider.
6. Lubrication.
7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
8. Normal product maintenance.
9. Misuse or abuse.
10. Normal wear and tear items such as light bulbs, fuses, and exterior finishes.

Warranty voided if:

1. Product is altered by user
2. Serial number plate is removed
3. Product is installed in a prison or any correctional facility.

Please keep this manual in a safe place for future use!