Veise RZ06 Smart Lock

User Guide / Installation Instruction

Thank you for purchasing Veise products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purposes only. Actual product may vary due to product upgrade.

Contact Veise Customer Support:

• Telephone: +1(855)400-3853 (Mon-Fri 9:00am-5:00pm EST)
• Email: support@iveise.com
• Amazon Customer Service: 24/7 email support

At a Glance

Exterior Assembly

The exterior assembly features a keypad for code entry, an IC card touch area, indicator lights, and a keyhole for backup key access.

Interior Assembly

The interior assembly includes the battery compartment, a thumb turn for manual operation, a privacy button, and a reset button.

How to Lock / Unlock

Unlock the Door from Outside

Enter your Master/User code followed by the '#' symbol. Alternatively, use a backup key.

Unlock the Door from Inside

Rotate the thumb turn on the interior assembly.

Lock the Door from Inside

• Auto Lock Mode: The bolt extends automatically 5 seconds after unlocking.
• Manual Mode: Press and hold '#' on the keypad for 2 seconds.

Manual Locking with Thumb Turn: Rotate the thumb turn to the lock position. For right-handed doors, turn the thumb turn vertically. For left-handed doors, turn it horizontally.

Definitions

• Master Code: The default master code is 123456. It is recommended to change this after pairing with the DDLock App.
• Auto Lock & One-touch Lock: Auto Lock extends the deadbolt automatically after the door is closed. One-touch Lock allows locking from the outside by pressing and holding '#' for 2 seconds.
• Private Mode: Activated by pressing and holding the 'Privacy button' on the inside panel for over 2 seconds. In this mode, unlocking via password and IC cards is disabled, but Bluetooth, physical key, and admin password unlocking remain available. Press the button once to disable Private Mode.
• Wrong Entry Limit: After 5 incorrect password attempts, the device will shut down for 2 minutes.
• Passage Mode: Keeps the lock unlocked until manually locked. Auto-lock is disabled in this mode.
• Anti-peeping Password: Allows entering random numbers before or after the correct password to prevent exposure. The total length of the anti-peeping password should be within 16 digits.

INSTALLATION INSTRUCTION

Parts List

• A: Backup Key x2
• B: Exterior Assembly x1
• C: Latch x1
• D: Strike x1
• E: Mounting Plate x1
• F: Exterior Assembly Screw (Optional)
• G: Interior Assembly x1
• H: Battery Cover x1
• I: Strike Screws x2
• J: Latch Screws x2
• K: Mounting plate Screws x2
• L: Interior Assembly Screws x3
• M: Reset Tool x1
• N: Drive-In Collar (Optional)
• O: IC card x2

If any parts are missing or damaged, please contact Customer Support.

1 Prepare the door and check dimensions

• A: Measure door holes: 1-1/2" or 2-1/8" (38mm or 54mm) for the main hole, and 1" (25mm) for the edge hole.
• B: Measure backset: 2-3/8" or 2-3/4" (60 or 70mm).
• C: Measure door thickness: 1-3/8" to 2" (35mm to 50mm).
• D: Ensure the hole in the door frame is at least 1" (25mm) deep for the deadbolt. Ensure the door frame is aligned and clear of obstructions.

2 Install the latch and strike

• Determine the backset and adjust the latch accordingly. Ensure the slotted hole is centered in the door hole. If not, rotate and pull the latch to extend it.
• Install the latch using Latch Screws (J).
• Test the deadbolt with a screwdriver to ensure it operates smoothly.
• Install the strike (D) on the door frame using Strike Screws (I). Ensure the hole in the door frame is at least 1" (25mm) deep.

3 Install exterior assembly

• Ensure the latch is fully retracted (unlocked position).
• Route the cable below the latch and insert the tailpiece through the latch slot.
• Secure the mounting plate (E) with Mounting plate Screws (K). Do not overtighten.

4 Install interior assembly

• Slide the battery cover (H) off.
• Determine if the door is right-handed or left-handed and set the slide switch accordingly. For right-handed doors, move the switch to 'R' and turn the thumb turn vertically. For left-handed doors, move the switch to 'L' and turn the thumb turn horizontally.
• Connect the cable from the exterior assembly to the socket on the interior assembly.
• Attach the interior assembly (G) to the mounting plate and secure it with Interior Assembly Screws (L).
• Insert 4 AA Alkaline batteries and replace the battery cover.

Factory Default Settings

How to Reset?

Press and hold the Reset button (M) on the interior assembly for 5 seconds using the Reset tool. A short beep and a green light flash indicate a successful reset. If the lock is paired, reset the button in the DDLock App settings before performing a physical reset.

Programming Guide

Note: The default master code is 123456. It is required to change the master code before programming. If the default master code was changed, reset the lock before pairing with the DDLock App.

• Change Master Code: Enter *123456# (default master code), then your new master code followed by #, and confirm with the same new master code followed by #.
• Add User Card: Enter *80# , then your Master Code followed by #, then scan the User Card.
• Add User Code: Enter *80#, then Master Code + #, then New User Code + #, then confirm with Same New User Code + #.
• Change User Code: Enter *10#, then Unwanted User Code + #, then New User Code + #, then confirm with Same New User Code + #.
• Delete All User Card: Enter *69#, then Master Code + #.
• Delete All User Code: Enter *71#, then Master Code + #.

Troubleshooting

• Lock won't accept inputs after incorrect entries: The lock enters a 2-minute lockout after 5 incorrect attempts. Unlock via the App or wait 2 minutes.
• How to lock manually from outside: Press and hold '#' on the keypad for 2 seconds.
• Batteries dead: Use the physical backup keys to unlock the door.
• Thumb turn won't turn: Check if the door direction (slide switch) was set correctly during installation. Refer to the installation guide or video.
• Latch won't extend completely: Ensure the exterior assembly is installed parallel to the door edge and not at a crooked angle.

FCC Statement

This equipment complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the manufacturer may void the user's authority to operate this equipment.

RF Exposure Information

This equipment complies with FCC radiation exposure limits for an uncontrolled environment. Maintain a minimum distance of 20 cm between the radiator and your body.

ISED Statement

This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSS standards. Operation is subject to two conditions: (1) this device may not cause interference, and (2) it must accept any interference, including interference that may cause undesired operation. This digital apparatus complies with Canadian CAN ICES - 3 (B)/NMB - 3(B). Users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits for an uncontrolled environment. Maintain a minimum distance of 20 cm between the radiator and your body.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to the lock's interior assembly and check settings regularly.
• Do not use an electric screwdriver during installation.
• No lock can provide complete security by itself.
• This lock can be defeated by forcible or technical means, or bypassed by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• For cleaning, use a soft, damp cloth. Avoid abrasive cleaners or polishes that may damage the finish.
• The lock is water-resistant but not waterproof. Avoid prolonged exposure to water or liquids.
• Avoid direct sunlight exposure, as it may damage the lock over time.