Jablotron JA-110P Bus PIR Motion Detector
This document was machine-translated from the original English version. In case of any ambiguity or doubt, please refer to the original document. If you encounter errors or have further questions, please contact technical support (contact information is at the end of this document).
The JA-110P product is a component of the JABLOTRON system. It is used for detecting human motion in indoor building spaces. Its detection characteristics can be altered by using an alternative lens. Immunity to false alarms is available in two options. The detector has an impulse response (reports only its triggering). The detector should be installed by a trained technician holding a valid certificate from an authorized dealer. This product is compatible with JA-101K, JA-102K, JA-103K, JA-106K, JA-107K.
Mounting
The detector can be installed on a wall or in a room corner. Its field of view should not contain objects that rapidly change temperature (e.g., electric heaters, gas appliances) or move (e.g., curtains hanging over a radiator), nor pets. It is not recommended to install the detector facing windows or spotlights, or in locations with excessive airflow (near fans, heat sources, air conditioning outlets, leaky doors, etc.). There should be no obstructions in front of the detector that could hinder its view.
Diagram 1: Mounting Holes
Illustration shows:
- 1 - Holes for mounting on a flat wall
- 2, 4 - Holes for mounting in a corner
- 3 - Retaining clip
- 5 - Cover latch
- Open the detector cover (by pressing the latch - 5). Avoid touching the internal PIR sensor (11) as you might damage it.
- Remove the circuit board – it is held by clip 3.
- Drill holes for the circuit board screws and the cable in the plastic base. The recommended mounting height for the detector is 2.5 m above the floor.
- Feed the bus cable through and fix the plastic base to the wall with screws (vertically, with the cover latch facing downwards). Important: Always switch off the power supply when connecting the detector to the system bus.
- Reinsert the circuit board and connect the bus cables to the terminals (8).
- Proceed according to the instructions for mounting the central control units.
Internal Settings
The detector's characteristics can be set in the Components list window of the F-Link software. When you are at the detector's location, open the Internal Settings option to access a dialog window for making settings:
- Immunity Level: Determines immunity to false alarms. The Standard immunity level (factory setting) combines basic immunity with a fast reaction. The Increased level offers higher immunity, but the detector's reaction is slower. To comply with standard EN 50131-2-2:2021, the Standard level must be used.
- Motion Detection LED: Allows the user to disable the motion detection indicator via a red LED.
Detection Characteristics
The standard lens supplied with the JA-110P detector covers a range of 110 degrees / 12 m. The range is monitored by 3 beams – see the following illustration.
Diagram 2: Detection Patterns
These detection characteristics apply to standard PIR immunity.
The characteristics can be altered by using an alternative lens:
| Lens Type | Description |
|---|---|
| JS-7910 | Equipped only with the upper beam, monitoring 120 degrees / 12 m and not covering the ground (can eliminate the motion of small pets on the floor). With this lens, the detector corresponds to the JA-110P PET type. |
| JS-7904 | For long corridors – with a working range of up to 20 m. Increased interference immunity cannot be used with this lens! When using this lens, the detector does not comply with standard EN50131-2-2:2021. |
| JS-7902 | Vertical curtain – it does not monitor an area but forms a detection wall (can be used to create a barrier and report its breach). When using this lens, the detector does not comply with standard EN50131-2-2:2021. |
Note: If a lens is replaced with a different type, test whether the detector monitors the area correctly (an incorrectly installed lens can cause detection errors).
Technical Parameters
The detector's terminals and components are illustrated below:
Diagram 3: Detector Terminals and Components
Illustration shows:
- 6 - Red LED indicator for detector activation
- 7 - Yellow fault indicator
- 8 - Digital bus terminals
- 9 - Serial number
- 10 - Tamper contact
- 11 - PIR sensor
| Parameter | Specification |
|---|---|
| Power Supply | From the bus 12 V DC (8...15 V) |
| Quiescent Current Consumption | 5 mA |
| Maximum Current Consumption | 10 mA |
| Recommended Installation Height | 2.5 m above the floor |
| Detection Angle / Detection Range | 110° / 12 m (with standard lens) |
| Dimensions | 60 x 98 x 52 mm |
| Weight | 75 g |
| Classification | Security Grade 2 / Environment Class II (according to EN 50131-1) |
| Operating Environment | Indoor areas generally |
| Operating Temperature Range | -10 °C to +40 °C |
| Average Operating Humidity | 75% RH, non-condensing |
| Certification Body | Trezor Test s.r.o. (No. 3025), Kiwa Nederland b.v. |
| Recommended Screw | 2x Ø 3.5 x 40 mm (countersunk head) |
Compliance and Disposal
Basic Procedure:
- Upon powering up the device, the yellow LED (7) will repeatedly blink, indicating that the module has not been registered in the system.
- Launch the F-Link software, select the desired position in the Components list window, and start the registration mode by clicking the Register option.
Declarations of Conformity
JABLOTRON a.s. hereby declares that the JA-110P product is in compliance with the relevant Union harmonization legislation: Directives No.: 2014/30/EU, 2011/65/EU, when used as intended. The original Declaration of Conformity can be found at www.jablotron.com - Downloads section.
The product complies with the following standards: EN 50131-1, -2-2, EN 50130-4, EN 55032, EN IEC 63000, T 031.
The product bears the CE and UKCA marks, indicating compliance with relevant EU and UK regulations.
Disposal Information
[WEEE Disposal Symbol] Proper disposal of this product helps to save valuable resources and avoid potential negative impacts on human health and the operating environment, which could otherwise arise from improper waste handling. Please return the product to the dealer or inquire with your local municipal authority for the nearest collection point.
