Corning Everon 6000 MIMO System User Manual
This document provides detailed information on Corning Optical Communications' Everon 6000 series MIMO systems, covering various configurations, component descriptions, LED indicators, software release versions, and essential RF safety guidelines.
MIMO Case Configurations
2x2 MIMO Case
This section describes the 2x2 MIMO Case configurations. The diagrams illustrate the interconnection of various units and the types of cables used.
Diagram 1: 2x2 MIMO Case (Top Configuration)
Depicts a 2x2 MIMO Case configuration. It shows a dLRU unit connected via multiple cables to a DEU unit. The DEU unit is connected to a DCU unit. The DCU unit is connected to a RIU-TDD unit. Finally, a BTS unit is shown connected to the RIU-TDD. A color-coded legend indicates the function of each cable: Blue for Ethernet Cable, Red for Power Cable, Yellow for Monitor Cable, Green for Optical Cable, Purple for Alarm Cable, Black for GND Cable, and Orange for RF Cable.
Diagram 2: 2x2 MIMO Case (Bottom Configuration)
Illustrates another 2x2 MIMO Case configuration, featuring a dLRU, DEU, DCU, RIU-FDD, and BTS. The connection flow is similar to the first diagram, with the same cable types and legend.
2TO1 2x2 MIMO Case
This configuration involves a dMRU unit connected to a DEU, then a DCU, then a RIU, and finally a BTS. The RIU unit has two output ports labeled OP 1 and OP 2. The cable legend is consistent with previous diagrams.
4TO1 2x2 MIMO Case
This configuration features a dLRU unit connected to a DEU, DCU, RIU, and BTS. The RIU unit has four output ports labeled OP 1, OP 2, OP 3, and OP 4. The cable legend remains the same.
Everon™ 6000 Parameters
Refer to the table below for Everon™ 6000 Parameters. The specific build is indicated as 'Parameters_Build'.
Release Versions
The following table lists the release versions for various components of the Everon 6000 system.
| SN | Unit | Version |
|---|---|---|
| 1 | RIU-TDD | 23.4.1.11_Everon_6000_RIU_P2.V01.00.00.11 |
| 2 | RIU-FDD | 23.4.1.11_Everon_6000_RIU_P2.V02.00.00.05 |
| 3 | DEU-25G | 23.4.1.11_Everon_6000_DEU_P2.V01.00.03.87 |
| 4 | DEU-10G | 23.4.1.11_Everon_6000_DEU_P2.V02.00.03. |
| 5 | DCU | 23.4.1.11_Everon_6000_DCU_P2.V01.00.03.83 |
| 6 | dLRU-3.5 | 23.4.1.11_Everon_6000_dLRUH_P2.V01.00.04.92 |
| 7 | dLRU-M | 23.4.1.11_Everon_6000_dLRUM_P2.V02.00.04.06 |
| 8 | dLRU-L | 23.4.1.11_Everon_6000_dLRUL_P2.V02.00.04.03 |
| 9 | dMRU-3.5 | 23.4.1.11_Everon_6000_dMRUH_P2.V01.00.03.51 |
| 10 | dMRU-FDD | 23.4.1.11_Everon_6000_dMRUF_P2.V02.00.00.46 |
| 11 | dHRU-FDD | 23.4.1.11_Everon_6000_dHRUF_P2.V01.00.01.68 |
| 12 | System Version | 23.4.1.11_Everon_6000_SYSTEM_P2.V01.04.03.38 |
LED Functionality and Color Definition
This section details the functionality and color indicators for the system's LEDs.
Optical LED Definition
| Green (SYNC) | Amber (LOS) | |
|---|---|---|
| SFP Plug out | OFF | OFF |
| Optic Link Fail | OFF | ON |
| 1. Optic cable disconnected | OFF | ON |
| 2. SFP fail | OFF | ON |
| 2.1 SFP fault | OFF | ON |
| 2.2 SFP warning | OFF | ON |
| 2.3 SFP alarm | OFF | ON |
| 3. CPRI link down | OFF | ON |
| Optic Link OK | ON | ON |
| 1. Optic cable connected | ON | ON |
| 2. SFP OK | ON | ON |
| 3. CPRI link down | ON | ON |
| CPRI Link OK | ON | OFF |
| 1. Optic cable connected | ON | OFF |
| 2. SFP OK | ON | OFF |
| 3. CPRI link up | ON | OFF |
ALM/RUN/Power LED Definition
| LED | Description | Color |
|---|---|---|
| ALM | 1. Alarm 2. Device detect (Identify and is controlled from DCU) 3. No alarm | Red Red Flash (1Hz, 10s) OFF |
| RUN | 1. The system is up and running 2. Software or hardware failure | Green Flash(1Hz) OFF |
| Power | 1. Power on 2. Power off | Green OFF |
RF Exposure and Usage Warnings
Caution message: The device is restricted for use with unauthorized antennas, cables, and/or coupling devices which may cause the device to not conform with ERP/EIRP limits and RF exposure requirements.
Warning: This device is for license operation and does not support home/personal use.
Warning! Each individual antenna used for this transmitter must be installed to provide a minimum separation distance as specified below or more from all persons and must not be co-located with any other antenna to meet RF exposure requirements.
Warning! Antenna gain should not exceed the specified limits.
Antenna Gain Specifications
| Model No. | distance | antenna gain |
|---|---|---|
| dHRU-G2-6 | 5.7m | 12.5dBi |
| dHRU-G2-7 | 7.7m | 12.5dBi |
| dHRU-G2-85 | 5.3m | 10dBi |
| dHRU-G2-19 | 5.4m | 12.5dBi |
| dHRU-G2-17 | 6.6m | 12.5dBi |
| dHRU-G2-23 | 3.8m | 12.5dBi |
WARNING ACCORDING TO PART 20
WARNING! This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation.
