300 Mbps Wireless N Router User Manual

Overview

This section provides an overview of the 300 Mbps Wireless N Router, including its physical components and indicator lights.

Router Diagram Description

The router is a compact device with several ports and buttons. Key components include:

• Reset/WPS Button (01): A button used for WPS pairing (press for 1 second) or device reset (press and hold for 5 seconds).
• LAN ports (02): Multiple Ethernet ports for connecting wired devices like computers or set-top boxes.
• WAN port (03): An Ethernet port for connecting to the internet modem or a wall Ethernet port.
• Power port (04): A port for connecting the power adapter.

Indicator Status

Ports and Buttons

Connecting to the Internet

Follow these steps to connect your router to the internet:

1. Power off the modem.
2. Connect the modem's LAN port to the router's WAN port using an Ethernet cable (RJ45). If your internet connection is directly from a wall Ethernet port, connect that cable to the router's WAN port.
3. Connect the power adapter (12V 0.5A) to the router's DC-IN port and turn it on.
4. Plug in the modem's power adapter.

Indicator Status: Solid red indicates power is on but the internet is not connected. Solid green indicates connection to the internet.

Set up the Network via a Web Browser

Configure your router's network settings using a web browser:

1. Connect your smartphone or computer to the Wi-Fi name (SSID) displayed on the device label on the router.
2. Launch a web browser. Enter 192.168.10.1 in the address bar.
3. Enter the default Username and Password found on the label at the bottom of the router to access the management page.
4. Navigate to the "Internet" page, select the appropriate WAN Type (e.g., DHCP), and click "Save". If unsure about the WAN Type, consult your Internet Service Provider.
5. Go to the "Wi-Fi" page. Change the SSID (Wi-Fi network name) and Password to enhance your Wi-Fi network security. Click "Save" to apply the configuration.

Note: Default Wi-Fi password and router management password can be found on the device label.

Frequently Asked Questions (FAQ)

• Q1: What should I do if I can't access the router's management page?

  Reboot your router and try again. Check your Wi-Fi connection. Try using a different web browser (e.g., Google Chrome). Restart your device.

• Q2: What should I do if I can't access the Internet?

  Reboot your modem and router, then try again. Verify that the internet connection is working by connecting the modem directly to a computer with an Ethernet cable.

• Q3: What can I do if I forget my wireless network password?

  If you haven't changed the default wireless password, it can be found on the label at the back of the router. Alternatively, connect your computer to the router via an Ethernet cable, log in to the web management page at IP Address: 192.168.10.1, and navigate to the "Install > Wireless" section to retrieve or reset your wireless password.

• Q4: What should I do if I forget my Web management page password?

  Check the Web password on the label at the bottom of the router. If you need to reset it, when the router is powered on, use a pin to press and hold the RESET button on the back until the LED blinks. This will restore the password to the default value shown on the label.

FCC Warning Statement

FCC Compliance Information:

• FCC Radiation Exposure Statement: The antennas used for this transmitter must be installed to provide a separation distance of at least 20 centimeters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
• Modification Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• Class B Digital Device Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Part 15 Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Security Warning

Please read and follow these precautions to ensure stable equipment performance and avoid dangerous or illegal situations:

• Use and store the equipment and its accessories within the temperature range of 0 to 40 degrees Celsius. Extreme temperatures may cause equipment failure.
• Maintain a distance of at least 20 centimeters between the human body and the device antenna during use.
• Only use accessories approved by the equipment manufacturer and compatible with this model. Using unapproved accessories may violate warranty terms, regulations, and lead to safety incidents. Contact an authorized service center for approved accessories.
• The power socket should be installed near the equipment and easily accessible.
• When not in use, disconnect the power supply from the device and unplug the power plug from the power outlet.
• Dispose of this device and its accessories as regular household waste, complying with local regulations and supporting recycling actions.

Hazardous Substances Table

This table indicates the presence of hazardous substances in the device's materials, in compliance with Directive 2011/65/EU (RoHS).

Legend:

• 'O': Indicates that the content of toxic and hazardous substance in all homogeneous materials is less than the specified limit by Directive 2011/65/EU (RoHS).
• '•': Indicates that at least one toxic and hazardous substance's content in all homogeneous materials is beyond the specified limit by Directive 2011/65/EU (RoHS).

Note: Hazardous substance information is based on supplier data and internal inspection. Efforts are made to improve product quality and replace hazardous substances where possible.

Manufacturer Information and Copyright

Quick Installation Guide

This document is protected by copyright. Without official written permission, no unit or individual shall copy, reproduce, transcribe, or translate any part or the whole book in any form or by any means (electronic, mechanical, printing, recording, or other possible means) for propagation of goods or for commercial, profitable purposes.

Dbit is the registered trademark of Shenzhen Dbit Network Equipment Co., Ltd. All other trademarks or registered trademarks mentioned in this document belong to their respective owners.

Product specifications and information mentioned in this manual are for reference only and are subject to updates without notice. Unless otherwise agreed, this manual is used only as a user guide. All statements and information do not constitute any form of guarantee.

Manufacturer: Shenzhen Dbit Network Equipment Co., Ltd

Address: 4002, Phase II, Qianhai Shimao Financial Center, No. 3040 Xinghai Avenue, Nanshan Street, Qianhai Shenzhen-Hong Kong Cooperation Zone, Shenzhen, China

Product images in the document are for reference only and are subject to physical appearance.

Quality Control: QC PASS

Copyright © 2025 Shenzhen Dbit Network Equipment Co., Ltd. All rights reserved.