AUVON Motion Sensor Night Light
Quick Start Guide
Description
The AUVON® night light automatically illuminates dark places when the ambient light level in the room is low and motion is detected. No more missing your target or stumbling around in the dark. Make your life brighter.
Getting Started
You need only 3 steps to enjoy your smart night light device experience.
1. Charge the device
Make sure the night light has enough power. Place the night light in an upright position, out of children's reach, and charge the device. For safety, please use the power cord included in the package. The suggested charging condition is 5V/1A.
Key Components:
- Luminous Area
- Sensing Area
- Charging Indicator
- Power Switch
- Brightness Button
- Magnetic Area
- Magnetic Pad
- 3M Adhesive Pad
2. Install Method
Install your night light with the adhesive mounting bracket.
Method One: Using Adhesive Bracket
- Remove the protective film on the back of the bracket.
- Stick the bracket onto the place where you need to illuminate.
- Use the built-in magnet to attract the bracket.
Important Note for Installation: Once the adhesive mounting bracket is fixed, please do not take it down, as it will be difficult to stick on the wall again.
Important Note for Charging: Take down the night light from the adhesive mounting bracket before recharging the night light.
Method Two: Direct Magnetic Mounting
Install the device directly to items that are made of iron.
Device Modes
- ON: Constant lighting mode (brightness can be changed with the right round button).
- OFF: Turn off the device.
- AUTO: Intelligent induction lighting mode. Automatically illuminates a dark place when the ambient light level is low and motion is detected. Lasts about 20 seconds.
Brightness Adjustment: Press the button down for high brightness; release for normal brightness.
Specifications
| Material | ABS |
|---|---|
| Sensor | Motion sensor, Light sensor |
| Light Source | LED |
| Voltage | 5V |
| Power | 0.4W |
| Lighting Mode | Constant lighting or induction lighting |
| Brightness | High or normal |
| Power Supply | Inside lithium cell |
| Sensing Range | 5m, 120 degrees |
| Dimensions | 55x56x29mm / 2.2×2.2×1.1 in |
| Weight | 0.09 lb / 39.5g |
Important Safety Information
- Please keep the packaging for future reference as it contains important information.
- To ensure correct and safe installation, use, and functioning of the product, always follow these instructions carefully and keep them for future reference.
- Do not use this apparatus near water. Avoid liquids and moisture on all electrical parts.
- Clean only with a dry, soft cloth. Household cleaners or solvents can damage your night light.
- Do not install your night light near any heat sources such as radiators, heat registers, stoves, or any other apparatus that produces heat.
- Do not block any ventilation openings.
- To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.
Warning:
- Keep packaging materials (e.g., plastic bags) out of children's reach.
- Not suitable for children under 36 months. Small parts may lead to choking hazard.
- Do not stare at the operating light source.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This smart night light is fully compliant with the EU, CA, and USA legislation. When disposing of this equipment, please help protect our environment by means of proper disposal. Your local authorities will have special return and disposal facilities available for you.
Customer Service
24-Month Limited Warranty
Lifetime Technical Support
Phone: +1(678)829-7256
Email: support@iauvon.com
Distributor:
Shenzhen Yuwen Dianzishangwu Youxiangongsi
Add: Longhuaxinqu longhuajiedao donghuanyilu 153hao zhonghuicaidasha7lou (gonghehuayuandamenpang) 703 Shenzhen Guangdong 518109 CN
E-mail: support@iauvon.com
Manufacturer:
Dongguan Nuomi Innovation Technology Co., Ltd.
Room 501, Building 1, No. 7, Industrial North Road, Songshan Lake Park, Dongguan City, Guangdong Province
Model: A5128
Made in China
UK REP: Prolinx Global LTD, 27 Old Gloucester Street, London, WC1N 3AX, UK
CE ROHS FCC UK CA
