Deerma Vacuum Cleaner DX118C
Precautions
Please follow these precautions for safe and effective use of the vacuum cleaner:
- Use the vacuum cleaner only as described in this manual.
- Ensure the vacuum cleaner's voltage matches your power supply.
- Avoid vacuuming hot objects, sharp fragments (like glass), harmful substances, liquids, flammable, or explosive materials (like gasoline or alcohol).
- Turn off the power and unplug the device before cleaning, repairing, or when not in use. Pull the plug by the plastic part, not the cord.
- Do not immerse the main unit in water. Avoid exposure to heaters or direct sunlight.
- Keep children away from the vacuum cleaner.
- Do not use the vacuum cleaner if it is damaged, shows abnormal operation, or has a damaged power cord. Contact a designated maintenance department.
- Avoid prolonged operation with a blocked suction inlet to prevent motor damage or deformation due to heat.
- The power cord is connected to the motor via a Y-type connection. If the power cord is damaged, it must be replaced by specialized equipment or a professional maintenance department.
Product Structure Diagram
The vacuum cleaner consists of the following parts:
- 1. Handle
- 2. Power cord hook
- 3. Metal tube
- 4. Power cord
- 5. Power switch
- 6. Dust panel frame
- 7. Dust panel frame switch
- 8. Strainer
- 9. Machine body
- 10. Round brush
- 11. Ground brush
Circuit Diagram: This diagram is for reference only. The product is subject to the actual object.
Application Method
Handle Lift Use:
- Press the dust panel frame switch to open the dust panel frame. Ensure the strainer is in place, then reassemble.
- Check that all parts are securely connected. Set the power switch to '0' (off).
- Open the buckle at the back of the main machine handle. Align the metal tube with the handle's center hole and insert it. Secure with the buckle.
- Align the ground brush with the power switch direction and insert it into the suction inlet. Ensure it's secure.
- Plug the power cord into the socket. Set the power switch to '1' (ON) to start.
- Turn the power switch to '0' (OFF) and unplug the device.
- Wind the power cord onto the hooks and store the cleaner upright.
Handle Push Use:
- Rotate the power cord hooks on the handle to release the power cord.
- Open the buckle from the metal tube's fixing block, pull out the handle, and secure the buckle to the main machine handle.
- Rotate the ground brush to loosen and remove it.
- Insert the brush nozzle into the suction inlet as shown.
- Plug the power cord into the socket. Set the power switch to '1' (ON) to start.
- Turn the power switch to '0' (OFF) and unplug the device.
- Press the dust panel frame switch, remove the dust panel frame and strainer, and empty the contents into a waste container.
Product Parameters
| Product name | Vacuum cleaner |
| Product model | DX118C |
| Rated voltage | 220-240V 50-60Hz |
| Rated power | 600W |
| Capacity | 1.2L |
| Vacuum degree | ≥15kPa |
| Noise | <82dB(A) |
Packing List
| Name | Quantity |
| Main machine | 1 |
| Ground brush | 1 |
| Flat suction mouth | 1 |
| Handle | 1 |
| Round brush | 1 |
| Manual | 1 |
Fault Analysis and Troubleshooting
Note: Cut off the power and unplug the power plug before troubleshooting.
The vacuum cleaner has a reduced suction force and an abnormal sound
Troubleshooting: Dredge the attachments.
Blocked ground brush or suction
Troubleshooting: Dredge the attachments.
Blocked strainer
Troubleshooting: Clean or replace the strainer.
Vacuum cleaner motor does not work
Troubleshooting: Check if the plug is securely plugged into the outlet and if the power is on.
The machine stopped working suddenly
Troubleshooting: Turn off the power switch, unplug the power plug. After the vacuum cleaner has cooled for 30 minutes, clean the dust panel frame and reuse. If the problem persists, contact a special maintenance department.
Cleaning and Maintenance
Daily Maintenance
Open the dust panel frame, take out the strainer, wash it with water, and let it dry naturally.
Precautions:
- Clean the strainer at least once a month. Clean it immediately if there is obvious accumulation. Dry the strainer before use after washing.
- Operate the vacuum cleaner with the strainer installed.
- Before using the vacuum cleaner again, ensure the strainer is installed and not damaged.
