Signature Design by Ashley W989-68 TV Stand Assembly Instructions
General Information and Safety
Note: Your unit may look different in appearance from the one shown in the illustrations on this instruction sheet.
General Assembly and Safety Guidelines:
- Proper maintenance of furniture surface paint is required; clean and polish regularly to avoid dust.
- For products with electrical wires (e.g., lamps): Ensure power is disconnected before installation and do not twist wires during installation.
- When installing shelves or TV cabinets, do not stand on lower shelves to install upper shelves; use a ladder for installation.
- Do not stand on coffee tables, end tables, or dining tables as they cannot support body weight.
- If assembly requires two or more people, do not attempt to assemble alone due to potential safety risks.
- Use appropriate tools for assembly.
- Follow assembly steps sequentially; do not skip any steps.
- Check packaging materials carefully for small parts that may have scattered. Contact the local retailer for missing parts; do not substitute.
- Periodically check all connections (screws, bolts, etc.) to ensure they are tightened.
- Keep these assembly instructions for future reference.
- Handle glass and mirrors with care during installation to prevent injury from breakage. Do not install large glass or mirrors alone.
Important Safety Notice: Please read the following guidelines carefully before assembling furniture!
Disclaimer: Signature Design by Ashley is not legally responsible for losses or injuries caused by failure to strictly follow assembly instructions, incorrect assembly, or improper product use.
Parts List
- A: 1x
- B: 1x
- C: 1x
- D: 1x
- E: 1x
- F: 1x
- G: 1x
- H: 2x
- J: 2x
- K: 1x
- L: 1x
- M: 4x
- N: 3x
- P: 12x
- R: 20x
- S: 4x
- T: 1x
- U: 8x
- W: 2x
- Y: 2x
- AA: 2x
- 100x20x8mm: 1x (Part not labeled with a letter)
- 160x65mm: 1x (Part not labeled with a letter)
Hardware List
- R (1/4" x 32mm Bolts): 20x
- S (1/4" x 76mm Bolts): 4x
- U (Ø8x30mm Dowels/Fasteners): 8x
- W (1/4" Washers): 2x
- Y (Brackets): 2x
- T (Cam Locks): 1x
- M (Cam Bolts): 4x
- AA (Anti-tip Restraint): 2x
- J (Fasteners): 16x (Used in Step 6, not listed on Page 2)
- Screws for Handles (used with P): 12x (Not explicitly lettered, but shown in Step 8)
- W (Screws for Fireplace): 2x (Labeled W in diagram, but W is also used for washers. See Step 11. These are 1/4" x 15mm)
- O (Fasteners for Fireplace): 16x (Used in Step 10, not listed on Page 2)
Assembly Steps
Step 1: Attach Side Panels to Base
Diagram shows panel A being attached to the base structure.
Attach side panels (A) to the main frame. Use eight (8) R bolts and two (2) W washers for each side panel. Ensure bolts are started but not fully tightened.
Step 2: Attach Center Panel
Diagram shows panel C being attached to the side panels.
Attach the center panel (C) to the side panels (A). Use eight (8) R bolts and two (2) W washers.
Step 3: Install Long Bolts and Dowels
Diagram shows long bolts (S) and dowels (U) being inserted into the frame.
Insert four (4) S bolts with washers into the designated holes on the frame. Insert four (4) U dowels/fasteners into their corresponding holes.
Step 4: Attach Panels D and E with Cam Locks
Diagram shows panels D and E being attached using cam locks (T) and cam bolts (M).
Attach panels (D) and (E) to the frame. Secure them using four (4) R bolts and four (4) T cam locks with M cam bolts. Insert the cam lock bolts into the panels and then turn the cam locks to secure.
Step 5: Insert Shelves
Diagram shows shelves (J) being slid into place.
Slide the shelves (J) into the pre-drilled slots within the unit. Ensure they are seated correctly.
Step 6: Attach Internal Supports/Back Panels
Diagram shows internal components being attached.
Attach internal supports or back panels using sixteen (16) J fasteners.
Step 7: Attach Top Panel
Diagram shows the top panel being placed and secured.
Place the top panel onto the assembled unit. Secure it using ten (10) R bolts and four (4) U dowels/fasteners.
Step 8: Attach Handles
Diagram shows handles (P) being attached to the doors with screws.
Attach the handles (P) to the doors. Use twelve (12) screws (likely T type, as shown in diagrams) for this purpose. Insert screws from the inside of the door into the handles.
Step 9: Install Anti-Tip Restraint
WARNING: The use of the included tipping restraint may reduce, but not eliminate, the risk of furniture tip over. Follow the instructions on the plastic bag for proper installation.
Diagram shows the anti-tip restraint (AA) being attached to the unit and a wall.
Attach the anti-tip restraint (AA) to the unit and a secure point (e.g., wall stud) as per the separate instructions provided with the restraint. This is a crucial safety step.
Note on Unlevel Surfaces: If the unit is placed on an unlevel surface, place a leveler underneath one foot until the unit is level. Break off any protruding segments.
Step 10: Optional Fireplace Insert Preparation
Note: When using the fireplace insert, please DO NOT use the optional back panel.
Diagram shows the area where the fireplace insert will be placed.
If installing the optional fireplace, ensure the designated area is clear. Do not install the optional back panel if using the fireplace insert. Use sixteen (16) O fasteners for attachment.
Step 11: Install Fireplace
Diagram shows the fireplace unit being inserted into the TV stand.
Insert the fireplace unit into the designated compartment. Secure it using two (2) W screws (1/4" x 15mm) and two (2) Y brackets.
Step 12: Fireplace Clearance Warning
WARNING: The gap between the fireplace's top and any obstacles above it must be a minimum of 1-1/2 inches. Failure to provide this minimum gap as instructed could result in a fire, bodily injury, death, or property damage.
Diagram illustrates the required clearance around the fireplace.
Ensure a minimum clearance of 1-1/2 inches (approximately 3.8 cm) between the top of the fireplace and any objects or surfaces above it to prevent fire hazards and ensure safety.
Ashley Furniture - Replacement Parts
