P783-820 Assembly Instructions
Signature Design by Ashley
Important Notes & Safety Information
Always use proper tools.
Follow the assembly steps in order. Do not skip any steps.
Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment. If parts are missing, contact the retailer from which you purchased the product to obtain any missing parts. DO NOT USE SUBSTITUTE PARTS.
Periodically check to ensure that all connectors (bolts, screws, etc.) are tight.
Keep the instructions for future reference.
Some assembly may involve attaching glass or mirrors. Be very careful handling the glass or mirrors, as severe injury may result if the glass or mirror breaks. Never handle large pieces of glass or mirrors by yourself.
When assembling products that have electric cords (lamps, light, etc.), always (1) make sure the electrical cord is unplugged before assembly and (2) be careful not to twist the electrical cord during assembly.
When assembling shelves or entertainment centers, do not stand on lower shelves in order to assemble upper shelves - use a step ladder.
Do not stand on tables, including but not limited to, end tables, coffee tables, and dinner tables, as tables are not to support the weight of a person.
Where assembly instructions state that the assembly requires two or more people, do not attempt by yourself as there is a risk of injury.
NOTE: ASHLEY FURNITURE INDUSTRIES, LLC DISCLAIMS ANY LIABILITY FOR DAMAGES OR INJURIES WHICH MAY OCCUR DUE TO FAILURE TO PROPERLY FOLLOW ASSEMBLY INSTRUCTIONS, PROPERLY ASSEMBLE THE PRODUCT, OR PROPERLY USE THE PRODUCT.
NOTE: YOUR UNIT MAY LOOK DIFFERENT IN APPEARANCE FROM THE ONE SHOWN IN THE ILLUSTRATIONS ON THIS INSTRUCTION SHEET.
This document is provided in multiple languages. The primary language used here is English.
Parts Identification
- Part A: Left side panel (x1)
- Part B: Right side panel (x1)
- Part C: Back panel (x1)
- Part D: Base panel (x1)
- Part E: Seat cushion (PA783-002) (x1)
- Part F: Back cushion (PA783-003) (x1)
- G: Bolts (1/4" x 65mm) (x12)
- J: Bolts (1/4") (x24)
- K: Bolts (1/4") (x12)
- L: Screws (x12)
- M: Screw (x1)
- N: Allen wrench (4mm) (x1)
Assembly Steps
Step 1: Preparation
Ensure all parts are accounted for. Assembly requires two or more people. Do not tighten any bolts until all bolts have been started.
[Diagram description: All parts A through N are shown laid out.]
Step 2: Frame Assembly - Sides to Base
Attach part D (base panel) to part A (left side panel) and part B (right side panel) using hardware G, J, K, L, M, and the Allen wrench N. Refer to the detailed diagrams for correct connection points. Two or more people are recommended for this step.
[Diagram description: Shows parts A, B, and D being joined. Zoomed views illustrate the connection points with specific hardware.]
Step 3: Frame Assembly - Attaching Back
Attach part C (back panel) to the assembled frame (parts A, B, D) using hardware G, J, K, L, M, and the Allen wrench N. Refer to the detailed diagrams for correct connection points.
[Diagram description: Shows part C being attached to the frame formed by A, B, and D. Zoomed views illustrate the connection points.]
Step 4: Tightening Hardware
Follow the specific tightening order to ensure structural integrity:
- Bottom of front 2 bolts.
- Top of back 2 bolts.
- Bottom of back 2 bolts.
- Then tighten all the remaining 6 bolts.
The tightening order was also provided in Spanish and French in the original document.
[Diagram description: Illustrates the sequence for tightening bolts on the assembled frame using the Allen wrench N.]
Step 5: Placing Seat Cushion
Place part E (seat cushion, labeled PA783-002) onto the assembled frame.
[Diagram description: Shows the assembled frame and the seat cushion (E) being placed onto it.]
Step 6: Placing Back Cushion
Place part F (back cushion, labeled PA783-003) onto the assembled frame.
[Diagram description: Shows the assembled frame with the seat cushion and the back cushion (F) being placed onto it.]
Step 7: Final Product
The assembly is complete. The final product is an armchair with seat cushion PA783-002 and back cushion PA783-003.
[Diagram description: Shows the fully assembled armchair with both cushions in place.]
Replacement Parts & Support
For replacement parts or support, please contact:
- Email: RTAParts@ashleyfurniture.com
- Website: www.ashleyfurniture.parts
- Phone: 1-844-966-0809
