Stetsom Moto Duplo i and Moto Triplo i Motorcycle Alarms

Control Functions and Alarm Response

1.1. Enable or Disable Periodic Transmission (Only CX-1P)

The CX-1P control comes from the factory with the presence transmission DISABLED. Before use, make sure the presence transmission is ENABLED. If it is disabled, the lock cycle will begin.

To enable or disable periodic transmission: HOLD * THEN PRESS ? ...until the led turns off and flash 1 time (ENABLE). ...until the led turns off and flash 2 times (DISABLE).

After use, it is recommended that the periodic transmission be disabled to extend CR2032 battery life (It is recommended that the battery be replaced every 4 months). When the ignition is turned on, the alarm will give 1 beep if the control battery is low.

Programming Controls

To Program: TURN ON IGNITION ➔ PRESS THE MASTER BUTTON ➔ UNTIL THE SIREN BEEPS. If the control is already programmed, the siren will emit 1 beep. Each time a new control is programmed to the control panel, the memory is cleared. Therefore, all existing controls must be reprogrammed with the new one or they will not work.

After the 10th beep, if it is not released, the button will not change the current setting.

Alarm Functions

3.1. Triggered Alarm

When the alarm is triggered, it immediately locks down. The alarm sounds for one minute, then waits 10 seconds and reads the sensors again. After the alarm has been triggered ten consecutive times by the accelerometer, this sensor is ignored until the next activation, unless the motorcycle is turned on.

3.2. Using the Control to Turn on the Motorcycle (Only Moto Triplo i)

PRESS ? FOR 3 SECS. ➔ SIREN EMITS 1 BEEP ➔ MOTORCYCLE TURNS ON ➔ PANEL TURNS ON AUTOMATICALLY ➔ PRESS *

• Press button for 3 seconds. A beep will sound, the motorcycle's panel will be activated, and if the button is pressed within 10 seconds the ignition will turn on (gray wire, positive current). As long as the button is held, the output remains active.
• To turn on the ignition, the motorcycle must be in Neutral ?.
• If you need to start the ignition again, press the button ? and then in 3 seconds *.
• To turn off the motorcycle, press the button ?, 2 beeps will sound and the motorcycle will turn off.
• If the motorcycle is in gear, it will not be switched off to prevent it from accidentally turning off when in motion.

Before checking the control panel, give it 10 seconds after it has been activated to stabilize all the sensors.

Enable or Disable Alarm

The control panel can be switched on and off by programming (see table section 12, function 2).

Integrated Anti-Theft System

5.1. Anti-Theft Function in Neutral

If the motorcycle is put in neutral while the ignition is on, the anti-theft function is activated. The MASTER BUTTON needs to be pressed within 3 minutes or the alarm will give a 10 second warning before entering lock down (see table section 12, function 6).

5.2. Anti-Theft Function Using the Ignition

Every time the ignition is turned on, the MASTER BUTTON needs to be pressed within 3 minutes or the alarm will give a 10 seconds warning before entering lock down (see section 11).

6 Anti-Theft by Presence

Activate and then deactivate periodic transmission: Hold ? and then press the button *. The control's led light will turn off and then blink 1 time for active periodic transmission or 2 times for deactivated periodic transmission.

To cancel the lock down, press the ? button on the presence control. In order to deactivate the control unit without the remote control, turn on the ignition and press the MASTER BUTTON. If the presence function is activated, the locks mentioned in sections 5.1 (ANTI-THEFT FUNCTION IN NEUTRAL) and 5.2 (ANTI-THEFT FUNCTION IN THE IGNITION) will not be functioning.

7 Testing Lock Down by Presence

Turn the ignition on and turn off the periodic transmission of the control (see section 1). Wait the specified time until lock down.

8 Valet Parking Function

If you need to leave your motorcycle at the mechanic, carwash, a place with valet service, etc., you can activate this function without showing them where the master button is or giving them the remote control.

Press the master button 3 times, it will emit 2 beeps and the locks mentioned in sections 5.1, 5.2 and 6 will be temporarily disabled. Each time the ignition is turned on or off, 2 beeps will sound to warn the user that the motorcycle is unprotected. To re-activate the anti-theft function, press the MASTER BUTTON once. If using the presence function, you need to press ? on the presence control near the motorcycle.

Disable/Disarm the Alarm Without the Control

The MASTER BUTTON needs to be installed in a concealed but easily accessible place. From this button, you can deactivate the control panel without the control by turning the ignition on and touching the MASTER BUTTON.

10 Progressive Lock Cycle

11 Automatic Lock

Confirm this function is working. If the motorcycle does not detect anything on any of the sensors in 1 minute, the alarm will activate automatically and the siren will give one beep (see table section 12, function 8).

Alarm Specifications

Installation

• Choose where the control module will be placed;
• To prevent shorts, use a multimeter to measure the current in the wiring and if possible insulate all connections before plugging the control module in;
• Be sure to secure the alarm module well before use;
• Follow the installation diagram to connect all the wires (signals and power) of the alarm;
• The separate resistor is only needed for Triple i installation on motorcycles Honda CG 160 Start/FAN/Titan 2017 forward;
• If you have any questions, please contact us: (SAC) 3003 1900.

Wiring Diagram

A diagram shows the connections for the alarm module, master button, ignition, neutral sensor, siren, blinkers, lock system, and power supply. Specific colors and connections are indicated for the Stetsom Alarm Module DUPLO i/TRIPLO i and for the TRIPLO i (HONDA CG 160 START/FAN/TITAN 2017) with a separate diagram showing the commutator side connector.

Note for Yamaha motorcycles: It is necessary to reverse the polarity of the starting signal to negative using an auxiliary relay (Relay Sold Separately).

Access the site for more information

Visit www.stetsom.com.br/instaladores to find specific installation information for different models of motorcycles. If you prefer, you can also access it from the QR CODE.

Environmental Responsibility: All parts of this product, including electrical and electronic components, must be recycled or reused and should not be disposed of as household waste. Look for recycle points for these materials and do your part to protect the environment.

Important Note: This equipment aims to deter theft and/or robbery of the vehicle, but like any other alarm available on the market, it is not capable of preventing them entirely. Life is the most precious asset that exists, always prioritize your safety.

Any updates made to this manual will be available for consumers to consult without any charge on the brand's site. It is recommended that the updated manual be consulted whenever necessary.

Images contained in this manual are merely illustrative and may differ from the actual product.

Warranty Information

STETSOM, through its network of Authorized Technical Assistance Providers, guarantees technical assistance to the purchaser of their products. The repairs of any defects duly established as being of the manufacturer will be done without cost for replacement components or parts and repair labor. The repairs will be done by the Authorized Technical Assistance Provider specially designated by STETSOM.

Consult the list of authorized technical assistance providers on our website:

www.stetsom.com.br/en/assistencias-tecnica

If you do not locate technical assistance in your city, please contact us at: USA 786 265 1960 or BR +55 18 2104-9412

Warranty Term Conditions:

Our warranty is 1 (one) year against manufacturing defects. Its validity starts on the date of the Sale to the FINAL Consumer. To make use of the benefits of this warranty, you must present one of the following documents: the Final Consumer's SALE NOTE or this completed CERTIFICATE.

Cases that Void the Warranty:

1. 1 year after the issuance of the invoice of sale to the consumer or 1 year of completing the certificate of warranty (dated and stamped by the retailer or installer) or 1 year from the date of manufacture.
2. Violation of seals, alteration or removal of the product's serial or lot number.
3. If the product suffers misuse, careless accidents involving: Water, Fire or Fall, or is installed in conditions contrary to the guidelines contained in the manual of installation that accompanies the product.
4. Damages and changes in the circuit or adaptation of non-original parts.
5. If you use installation techniques contrary to those given in the manual.

Questions and Advice:

STETSOM offers Customer Services to answer questions and give advice about their products and services. Please contact us through the channels:

Phone: USA 786 265 1960 cost of a local call.

E-mail: suporte@stetsom.com.br - Site: www.stetsom.com

Warranty Certificate Fields

Fields for entering the product's serial number, date of purchase, month/year of manufacturing, and dealer/stamp information are provided.