Stetsom Evolution Moto Automotive Alarm

1. Functions of the Control and Response of the Alarm

This section details the functions of the alarm control and the corresponding responses.

Note: Functions for turning on the panel and starting the motorcycle are available only in the TRIPLO i model.

1.1. Enable or Disable Periodic Transmission (Only CX-1P)

The CX-1P control comes from the factory with the presence transmission DISABLED. Before use, ensure the presence transmission is ENABLED. If disabled, the lock cycle will begin.

To Enable: HOLD ⭐ THEN PRESS ? ...until the LED turns off and flashes 1 time.

To Disable: HOLD ⭐ THEN PRESS ? ...until the LED turns off and flashes 2 times.

Battery Reminder: After use, it is recommended to disable periodic transmission to extend CR2032 battery life. Battery replacement is recommended every 4 months. The alarm will emit 1 beep upon ignition if the control battery is low.

2. Programming Controls

To Program: TURN ON IGNITION, PRESS THE MASTER BUTTON UNTIL THE SIREN BEEPS.

After Programming: TURN OFF IGNITION, EMITS 3 BEEPS FOR EACH PROGRAMMED CONTROL, PRESS ? AND ⭐ TOGETHER.

Note: If a control is already programmed, the siren will emit 1 beep. Each time a new control is programmed, the memory is cleared, and all existing controls must be reprogrammed.

3. Alarm Functions

3.1. Triggered Alarm

When the alarm is triggered, it immediately locks down. The alarm sounds for one minute, then waits 10 seconds and reads the sensors again. After ten consecutive triggers by the accelerometer, this sensor is ignored until the next activation, unless the motorcycle is turned on.

3.2. Using the Control to Turn on the Motorcycle (Only Moto TRIPLO i)

To Start: PRESS ? FOR 3 SECS. Siren emits 1 beep. Panel turns on automatically. MOTORCYCLE TURNS ON. PRESS ⭐.

• Press ? button for 3 seconds. A beep will sound, and the motorcycle's panel will be activated.
• If the ⭐ button is pressed within 10 seconds, the ignition will turn on (gray wire, positive current). The output remains active as long as the button is held.
• The motorcycle must be in Neutral Ⓝ to turn on the ignition.
• To restart the ignition, press the ? button and then ⭐ in 3 seconds.
• To turn off the motorcycle, press the ? button; 2 beeps will sound, and the motorcycle will turn off.
• If the motorcycle is in gear, it will not turn off to prevent accidental shutdown while in motion.

Important: Before checking the control panel, wait 10 seconds after activation for all sensors to stabilize.

4. Enable or Disable Alarm

The control panel can be switched on and off by programming (see table in item 12, function 2).

5. Integrated Anti-Theft System

5.1. Anti-Theft Function in Neutral

If the motorcycle is put in neutral while the ignition is on, the anti-theft function is activated. The MASTER BUTTON needs to be pressed within 3 minutes, or the alarm will give a 10-second warning before entering lock down (see table section 12, function 6).

5.2. Anti-Theft Function Using the Ignition

Every time the ignition is turned on, the MASTER BUTTON needs to be pressed within 3 minutes, or the alarm will give a 10-second warning before entering lock down (see section 11).

6. Anti-Theft by Presence

Activate and deactivate periodic transmission: Hold ⭐ and then press the ? button. The control's LED will turn off and then blink 1 time for active periodic transmission or 2 times for deactivated periodic transmission.

To cancel lock down: Press the ? button on the presence control.

To deactivate the control unit without the remote control: Turn on the ignition and press the MASTER BUTTON. If the presence function is activated, the locks mentioned in sections 5.1 (Anti-Theft Function in Neutral) and 5.2 (Anti-Theft Function in the Ignition) will not be functioning.

7. Testing Lock Down by Presence

Turn the ignition on and turn off the periodic transmission of the control (see section 1). Wait the specified time until lock down.

8. Valet Parking Function

If you need to leave your motorcycle at a mechanic, carwash, or valet service, you can activate this function without showing the master button's location or giving them the remote control.

Press the master button 3 times; it will emit 2 beeps, and the locks mentioned in sections 5.1, 5.2, and 6 will be temporarily disabled. Each time the ignition is turned on or off, 2 beeps will sound to warn the user that the motorcycle is unprotected. To re-activate the anti-theft function, press the MASTER BUTTON once. If using the presence function, you need to press ? on the presence control near the motorcycle.

9. Disable / Disarm the Alarm Without the Control

The MASTER BUTTON needs to be installed in a concealed but easily accessible place. From this button, you can deactivate the control panel without the control by turning the ignition on and touching the MASTER BUTTON.

10. Progressive Lock Cycle

LOCK FOR 2 SECS. → UNLOCK FOR 10 SECS. → LOCK FOR 2 SECS. → UNLOCK FOR 5 SECS. → COMPLETELY LOCKED → UNLOCK FOR 2 SECS. → LOCK FOR 2 SECS.

11. Automatic Lock

Confirm this function is working. If the motorcycle does not detect any of the sensors in 1 minute, the alarm will activate automatically and the siren will give one beep (see table section 12, function 8).

12. Programming

Process: ALARM DISABLED → TURN ON IGNITION → PRESS THE MASTER BUTTON → LISTEN CONSECUTIVE BEEPS OF THE FUNCTIONS → RELEASE THE MASTER BUTTON AT THE DESIRED FUNCTION.

Activation/Deactivation: 1 BEEP ACTIVATED, 2 BEEPS DEACTIVATED.

Note: After the 10th beep, if the button is not released, the current setting will not change.

13. Alarm Specifications

Alarm Module

• Operating Voltage: 9 – 15 VDC
• Max. Current for Blinkers: 5 A
• Max. Current for Locks: 10 A
• Remote Control's Frequency: 433.92 Mhz
• Consumption: 8 mA

14. Installation

• Choose where the control module will be placed, ensuring it is not under the fuel tank and is as far as possible from the CDI.
• Use a multimeter to measure the wiring and insulate all connections before plugging in the control module to prevent shorts.
• Secure the alarm module well before use.
• Connect all wires (signals and power) according to the installation diagram.
• A separate resistor is only needed for Triple i installation on Honda CG 160 Start/FAN/Titan 2017 models and onwards.
• For questions, contact Stetsom at (BR) +55 18 2104-9412.

Wiring Diagram Description:

The diagram shows the connections for the Alarm Module (DUPLO i / TRIPLO i). Key connections include:

• Master Button (Black): Connected to Ground.
• Ignition (Purple): Only for TRIPLO i, connected to Ignition.
• Ignition (Blue): Connected to Ignition.
• Neutral (Brown): Connected to Neutral.
• Siren (Black/Yellow): Connected to Siren and Ground.
• Lock System (Yellow): Connected to the Lock System.
• 12V Power (Red +12V): Connected to Power.
• Blinkers (Black/Green): Connected to Blinkers.
• START + (Gray): Only for TRIPLO i, connected to START.
• Ground (Black): Connected to Ground.

Yamaha Motorcycle Note: For Yamaha motorcycles, it is necessary to reverse the starting signal to negative using an auxiliary relay (sold separately).

TRIPLO i (HONDA CG 160 START/FAN/TITAN 2017) Connector Details:

The diagram shows the specific connector for Honda CG 160 models. It details:

• DISCONNECT AND ISOLATE: Pink wire, Blue (Alarm) wire, Red/Black or Blue/Black wire.
• RESISTOR 1K2: Brown, Red, Golden wires.
• COMMUTATOR Side: Red wire, Pink wire.
• Connector HONDA CG 160 START/FAN/TITAN 2017: Red wire, Pink wire, White/Black wire, Purple (Alarm) wire.

Additional Information:

• Access www.stetsom.com.br/instaladores for specific installation materials for different motorcycle models.
• Recycling: All parts of this product, including electrical and electronic components, must be recycled or reused and not disposed of as household waste. Look for recycle points.
• Disclaimer: This equipment is designed to deter theft but cannot prevent it entirely. Prioritize safety.
• Manual Updates: Any updates to this manual will be available on the brand's website. Consult the updated manual when necessary.
• Images are illustrative and may differ from the actual product.

Warranty Information

Stetsom guarantees technical assistance for product repairs due to manufacturing defects at no cost for components, parts, or labor. Repairs are performed by Authorized Technical Assistance Providers designated by Stetsom.

Consult Authorized Providers: www.stetsom.com.br/en/assistencias-tecnica

Contact for Assistance: BR +55 18 2104-9412

Warranty Term Conditions: 1 year against manufacturing defects, starting from the date of sale to the FINAL Consumer. Proof of purchase (SALE NOTE or CERTIFICATE OF WARRANTY) is required.

Cases That Void the Warranty:

1. After 1 year from the invoice date, warranty certificate completion, or manufacture date.
2. Violation of warranty seals, alteration, or removal of serial/lot number.
3. Misuse, accidents (water, fire, fall), or installation contrary to manual guidelines.
4. Damage or changes to the circuit or adaptation of non-original parts.
5. Installation techniques contrary to manual specifications.

Questions and Advice: Contact Stetsom Customer Service (SAC) via Phone: BR +55 18 2104-9412 or Email: suporte@stetsom.com.br. Website: www.stetsom.com.br

Attention: Listening to music above 85 decibels can cause hearing damage (Federal Law nº 11.291/06).

Additional Information

MOTO DUPLO i

2 x CX-1

MOTO TRIPO i

1 x CX-1, 1 x CX-1P

ANATEL: CX-1 / CX-1P, Nº 02319-19-09020. "This equipment has no right to protection against harmful interference and may not cause interference in duly authorized systems." In accordance with ANATEL.

Maximum Protection For Your Vehicle!

Explore the full line of Stetsom alarms, blockers, and accessories. Access the Link or use the QR CODE.

SITE: www.stetsom.com.br/pt/produtos/alarms

WARRANTY CERTIFICATE

Serial / Serial number:

Data da compra / Date of purchase:

Mês / Ano de fabricação: / Month / Year of manufacture:

Revendedor / Carimbo: / Reseller / Stamp:

STETSOM INDUSTRIA ELETRÔNICA LTDA. - CNPJ: 61.974.911/0001-04

RUA MARIANO ARENALES BENITO, 645 - DISTRITO INDUSTRIAL - CEP 19043-130

PRESIDENTE PRUDENTE/SP - BRASIL

www.STETSOM.com.br

R16