HAVSTA Console Table
Design and Quality IKEA of Sweden
Product Overview
This document provides assembly instructions for the IKEA HAVSTA console table. Please follow these steps carefully to ensure correct assembly.
Parts List
- Dowel with Screw (Part 118331) - Quantity: 4x
- Cam Lock Nut (Part 112996) - Quantity: 4x
- Screw (Part 113434) - Quantity: 8x
- Wooden Dowel (Part 108442) - Quantity: 10x
- Connector Bolt (Part 101345) - Quantity: 2x
- Screw (Part 112366) - Quantity: 10x
- Long Screw (Part 109570) - Quantity: 4x
- Threaded Rod (Part 111451) - Quantity: 4x
- Nut (Part 104875) - Quantity: 4x
- Bracket (Part 102335) - Quantity: 4x
- Wrench (Part 100089) - Quantity: 1x
- Hardware Pack (Part 105867) - Quantity: 1x (Contains various small screws and washers)
Tools required: Screwdriver (Phillips and flathead) ?.
Important Safety Note: ❌ [Incorrect Assembly] Assembling the product incorrectly can lead to damage. Assemble on a soft surface like a rug ? to prevent scratches.
If you encounter issues or have questions, please refer to IKEA support. ?
Assembly Instructions
Step 1
Attach the two long side frame pieces to the two short base frame pieces using 8x screws (108442). Ensure the pieces are aligned correctly.
Step 2
Insert 4x dowels with screws (118331) and 4x cam lock nuts (112996) into the pre-drilled holes on the inside of the side panels. The arrow on the cam lock nut should point towards the hole where the screw will enter.
Step 3
Screw 4x threaded rods (111451) into the designated holes on the base frame. Tighten them securely.
Step 4
Insert 4x wooden dowels (101345) into the holes on the bottom of the two vertical support pieces. ? [Magnified view shows dowel insertion]
Step 5
Attach the vertical support pieces to the frame. Align the holes with the threaded rods. Secure each side using 2x brackets (102335) and 2x nuts (104875), using the wrench (100089) to tighten.
Step 6
Insert 4x wooden dowels (101345) into the top holes of the vertical support pieces. ? [Magnified view shows dowel insertion]
Step 7
Secure the vertical support pieces to the frame by inserting and tightening 2x cam lock nuts (113434) on each side. Turn the cam lock nut clockwise ? until it locks the piece in place.
Step 8
Place the two top frame pieces onto the assembled base structure. Ensure they align with the dowels and holes from the vertical supports.
Step 9
Secure the top frame pieces to the vertical supports. Use 2x brackets (102335) and 2x nuts (104875) per side, tightening with the wrench (100089).
Step 10
Secure the top frame pieces further by inserting and tightening 2x cam lock nuts (113434) on each side. Turn the cam lock nut clockwise ? until it locks.
Step 11
Insert 2x wooden dowels (101345) into the designated holes on the top frame. ? [Magnified view shows dowel insertion]
Step 12
Carefully flip the assembled frame upside down onto a soft surface, such as a rug ?. ⬇️ [Flip action]
Step 13
Attach the bottom shelf support rails to the underside of the frame. Use 10x long screws (109570) to secure them in place.
Step 14
Insert 2x connector bolts (112366) into the designated holes on the top frame. ? [Magnified view shows bolt insertion]
Step 15
Carefully flip the unit upright. ⬆️ [Flip action]
Step 16
Slide the top panel into place. Ensure it aligns correctly with the frame and the connector bolts (112366). ➡️ [Slide action]
Assembly Complete
Your HAVSTA console table is now assembled. Ensure all connections are secure before use.
