RYOBI P2809 Electrostatic Sprayer Quick Start Guide

Safety Information

DANGER: Risk of fire or explosion. Do not spray flammable liquids such as gasoline. Look for this symbol reference on the container. ?

DANGER: Do not use this sprayer in a flammable, explosive or oxygen rich environment.

WARNING: This Quick Start Guide is not a substitute for reading and following the operator's manual. To reduce the risk of serious injury, user must read and understand the operator's manual before using this product.

WARNING: Do not use this sprayer or enter the spray area if you have a pacemaker, implantable cardioverter defibrillator (ICD), internal pump, or any other similar medical device. Do not use on or near electrical medical equipment.

CAUTION: Wear shoes with a leather sole while using this sprayer. Do not wear shoes with a rubber sole, or similar insulating footwear.

• Know the contents of the chemical being used. Read all Safety Data Sheets (SDS) and container labels provided with the chemical. Follow the chemical manufacturer's directions, requirements, and safety instructions. Follow CDC and EPA guidelines for cleaning. It is a hazard and a violation of federal law to use an EPA-approved disinfectant in a manner inconsistent with its labeling.
• CAUTION: To reduce the risk of electric shock, do not touch the nozzle during use. ⚡
• CAUTION: Keep all body parts out of the spray pattern.
• CAUTION: When spraying conductive surfaces with the electrostatic function enabled, a charge could build up on the conductive surface potentially resulting in a static shock to the user. Carrying a secondary conductive item (such as a key) to touch the surface and dissipate the charge is recommended.
• Do not use bleach, alcohol-based chemicals or hydrogen peroxide.
• Do not combine chemicals.

The spray area must be well ventilated.

To reduce the risk of fire or explosion use a liquid with a flash point higher than 140°F (60°C).

Before filling the tank, always remove the battery pack. Wipe up any spills before inserting the battery pack.

Do not leave residue or spray material in the tank after using the sprayer. Clean after each use.

Getting Started

1. Fill the Tank

   Be sure to follow the chemical manufacturer's instructions for mixing. Do not overfill the tank.

2. Install the Battery Pack

   Make sure the latches on each side of the battery pack snap in place and that the battery pack is secured in the tool before beginning operation.

3. Use the Anti-Static Strap

   Slip the anti-static band onto your wrist or arm. Lift the locking tab and pull the end of the strap to tighten as needed. After adjusting, lower the locking tab to secure to the strap. The anti-static strap must be fastened to the user in a place that makes direct contact with the user's skin.

4. Turn On the Sprayer

   To turn the sprayer ON, depress the switch trigger. NOTE: If the sprayer has trouble priming or will not spray when the tank is filled, the pump has lost its prime. Turn the nozzle selector dial to the largest micron setting and pull the switch trigger. Once the spray is even and consistent, release the switch trigger and rotate the nozzle selector dial to the desired position.

5. Using the Electrostatic Function

   Place the switch located on the bottom right side of the unit to ON (I) position.

6. The 3-in-1 Rotating Nozzle

   Select a spray pattern, rotate the nozzle selector to the desired spray pattern.

   • Low: 65 microns (TX-1.5)
   • Medium: 85 microns (TG-0.4)
   • High: 160 microns (TG-1)

After Use

REMOVE THE BATTERY PACK AND THOROUGHLY CLEAN THE SPRAYER AFTER EACH USE.

Support & Resources

NEED HELP? 1-800-525-2579

Go to www.ryobitools.com and register your new tool on-line.

For any questions about operating or maintaining your product, call the RYOBI Help Line! Your product has been fully tested prior to shipment to ensure your complete satisfaction. Troubleshooting tips are also available in your operator's manual.