Rockville RockPAR50

Welcome

Thank you for purchasing the Rockville RockPAR50 Compact RGB LED Par Can Wash Light. Please read this guide carefully for proper use of your RockPAR50.

For assistance, please call our technical help line at 1-646-758-0144, Monday through Thursday, 9am to 10pm EST., and Fridays, 9am to 3pm EST.

What's Included

• Par Light
• Power Cable
• Dual-Bracket
• Owner's Manual
• Warranty Card

Important Safety Instructions

CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.

NO USER SERVICEABLE PARTS INSIDE. WE RECOMMEND TAKING THE UNIT TO A QUALIFIED SERVICE TECHNICIAN FOR ANY REPAIRS.

• To reduce risk of electric shock, never open the unit. Refer service to an authorized Rockville service center.
• Avoid looking directly into the lights.
• Do not expose this unit to any kind of moisture.
• The product's housing may become hot during operation. Do not touch.
• Ensure the unit is situated in a properly ventilated area, allowing at least 20 inches between the device and a wall.
• This device has an IP20 rating and is intended for indoor use only.
• Do not operate this unit when the cover is open.
• Do not attempt to operate this unit if the power cord is frayed or broken.
• Do not attempt to break off or remove the ground prong; it reduces the risk of electrical shock and fire in case of an internal short.
• Never plug this unit into a dimmer pack.
• Do not operate this unit if it is damaged.
• During long periods of non-use, disconnect the unit from the power source.
• Always mount this unit in a safe and stable manner.
• Route power supply cords so they are not likely to be walked on or pinched, paying attention to the point of exit from the unit.
• To avoid unnecessary wear and improve lifespan, unplug the unit when not in use for extended periods.
• Assembly and installation must be carried out by a specialist familiar with hazards and regulations. Maintenance, operation, and commissioning must only be carried out by qualified persons.
• When choosing a location, avoid impact, vibration, dust, hot/cold temperatures, and dampness. Do not place near powerful transformers or motors.
• Operate the effect light at a maximum ambient temperature of 40° C.
• Never cover the device. Ensure sufficient ventilation when mounting with other equipment. Maintain a distance of at least 0.5 meters to other devices and walls. Never install in proximity of heat sources. Do not point strong spot lights or light sources towards the device, as this may cause overheating.
• Do not drill or screw additional screws into the casing; this may expose dangerous voltage.
• The device must be mounted out of normal reach.
• Illuminated objects must be at least 0.5m away from the device's light emission source. Easily flammable materials must also be at least 0.5m away to prevent fire.
• When mounting, ensure the power cord is not jammed or damaged by sharp edges.
• During installation or service, cordon off the area below the installation point.
• The installation surface or mounting fixture must be designed to withstand ten times its load capacity for at least one hour without permanent deformation.
• Secure the device with a second safety restraint, independent of mounting supports, when installing in an elevated position. No part must fall if the main suspension system fails.
• Observe all relevant regulations of your country when installing.
• Acceptance test (industrial/public use): Before first use and after significant modifications, installation must be inspected by an official expert. A yearly inspection by an expert is required. At least every four years, an acceptance test must be carried out by an expert.
• For traverse system mounting, attach the effect light with the mounting bracket and a suitable traverse clamp (sold separately). Install the effect light using the assembly bore of the mounting bracket to the traverse clamp, then to the traverse system. Use only suitable assembly material.
• The assembly must never swing freely.
• Additionally secure the installation with a suitable safety restraint cable or safety net to support the light in case of main support system failure.

Unit Functions

The unit features the following connection and control points:

• 1. DMX out: XLR connector for DMX output.
• 2. Rubber feet: For stable placement.
• 3. LCD display: Shows current settings and modes.
• 4. DMX in: XLR connector for DMX input.
• 5. Power linking socket (power out): IEC connector for power output to link other units.
• 6. Mic: Built-in microphone for sound-activated modes.
• 7. IEC AC power socket: Standard IEC connector for power input, with a user-serviceable fuse.
• 8. Controls:
  • Mode: Press repeatedly to cycle through mode options.
  • Up: Scroll up through settings.
  • Down: Scroll down through settings.
  • Enter: Use to make selection.

Operation

DMX

To set the DMX starting channel address, press the Mode button until "d---" is displayed. Use the Up and Down buttons to select the desired address, then press Enter to save.

Internal Programs

To select and run one of the four built-in programs, press the Mode key until the desired program is found.

DMX Termination

The last fixture in a DMX chain must be "terminated" to prevent electrical noise from corrupting DMX control signals. To terminate, solder a 1/4 Watt, 120 ohm resistor across the DATA - and DATA + wires of the last fixture. The diagram shows typical connections. For short runs with few fixtures, termination may not be necessary.

DMX Chain Illustration:

Diagram showing 6 fixtures connected in a daisy-chain. Fixtures 1 through 5 have DMX IN and DMX OUT. Fixture 6 (last fixture) also has DMX IN and DMX OUT, with a visual representation of a 120 Ohm resistor connected between the DATA- and DATA+ pins of the DMX OUT connector.

Termination Resistor: A close-up shows a DMX connector with pins 1 (DATA-), 2 (DATA+), and 3 (Ground). The 120 Ohm resistor is shown connected between pins 1 and 2.

Modes and DMX Channels

Modes

DMX Channel Values and Functions

3 Channel Mode: a001 – a512

6 Channel Mode: d001 – d512

Maintenance and Cleaning

Always follow safety instructions before cleaning or servicing:

• Live components may be exposed if covers are opened or components removed.
• Disconnect the device from all power sources before servicing or repair.
• Capacitors may still carry voltage even after disconnection.
• Only qualified experts familiar with hazards and regulations should perform repairs.
• Never use aggressive cleaning agents, alcohol, or chemical solutions, as they may damage the casing or impair function.
• Always disconnect the product from the power supply before cleaning.
• Use a dry, lint-free cloth for cleaning.

Handling

• Never connect the mains plug to a socket immediately after moving the device from a cold to a warm environment to avoid condensation damage. Allow the device to reach room temperature first.
• Never pull the mains plug by the cable; pull it by the intended grip areas.
• Unplug the mains plug if the device is not used for an extended period.
• Disconnect the mains plug during thunderstorms for safety.
• Never place filter foils, masks, or other materials over the light exit, as this may cause heat damage and fire.
• The device may heat up during operation; do not touch the casing. Let it cool off before touching or cleaning.
• Do not cover the device to ensure sufficient ventilation. Air circulation must not be impaired by objects like magazines, tablecloths, or curtains. Maintain a minimum distance of 0.5 meters around the device.
• The device is not suitable for continuous operation. Consistent compliance with operating breaks increases its lifespan. Allow it to cool off for an extended period before operating again.

Features and Specifications

• Rockville RockPAR50 Compact RGB LED Par Can Wash Light
• Power input and output for linking multiple units using one wall outlet.
• DMX in and out for daisy chaining multiple lights for synchronized control.
• Three or six channels of DMX control.
• Operation Modes: Auto, Voice activated, Master-Slave, DMX512.
• Functions: Strobe, color change, color fade, dimmer, ID address, color mixing controls.
• Colors: 16.7 million different color variations.
• Double-bracket serves as floor stand and hanging bracket.
• Static colors and RGB color mixing with or without DMX controller.
• Strobe effect with adjustable speed.
• Built-in automated programs via master/slave or DMX with variable speed.
• Slim profile with powerful and long-lasting LEDs.
• Beam angle: 15°, 25°, 35°, and 45°.
• Light source: Eighteen high power 1 watt LEDs (six red, six green, and six blue).
• Dimmer: 0 – 100%.
• Input Voltage: 110 – 240V, 50/60Hz.
• Power Consumption: 24W.
• Advanced switching power supply.
• Constant current protects LEDs from blowing.
• LED life: 20,000 - 100,000 hours.
• IP grade: 20.
• 110/220 switchable.
• Unit dimensions: 7.01″ x 4.33".
• Unit weight: 1.43Lbs.

Troubleshooting