Event Lighting PAR19X12L
19x 12W LED RGBWAU Parcan with IR Remote
USER MANUAL
Version 1.1
Important Safety Information
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult your local Kookaburra Account Manager for any clarification or information regarding this item.
Warning
- Do not open this device; there are no user-serviceable parts inside. ⚡️ Risk of electric shock.
- Do not look directly at the light source from close range.
- Avoid contact with the unit during operation, as the housing may become hot. Allow the fixture to cool for at least 15 minutes after turning off before touching.
- Install this device in a location with adequate ventilation, at least 50cm from adjacent surfaces.
- Do not operate this device, or connect this device to power, within 50cm of any flammable material.
- Use a safety chain when mounting this device overhead.
- Do not operate this device outdoors where excessive dust, heat, water, or humidity may affect it.
- Do not operate this device if the housing, lenses, or cables appear damaged.
- Do not connect this device to a dimmer or rheostat.
- Do not operate this device at temperatures higher than 40°C (104°F).
- Only connect this device to a grounded and protected circuit.
- Only use the hanging bracket to carry this device.
- Stop using this device immediately if a serious operating problem becomes apparent.
Coin/Button Cell Battery Safety Information
⚠️ This product includes an IR remote that contains a coin/button cell battery. If the battery is swallowed, it can cause severe internal burns and, in extreme cases, can lead to death. Keep batteries away from children.
Product Installation
PAR19X12L can be mounted in many orientations, provided each individual device is secured by the use of the correct mounting bracket. Use a safety chain when mounting PAR19X12L overhead.
Dimensions
The device has the following approximate dimensions:
- Side View: Height 214mm, Depth 270mm, Width at bracket 84mm.
- Front View: Width 275mm.
Lux Chart @40°
| Lux | 1m | 2m | 3m | 4m | 5m |
|---|---|---|---|---|---|
| R | 2,850 | 650 | 290 | 162 | 107 |
| G | 4,310 | 1,112 | 495 | 286 | 180 |
| B | 6,290 | 1,340 | 670 | 385 | 250 |
| W | 4,850 | 1,278 | 598 | 349 | 230 |
| A | 705 | 170 | 82 | 43 | 32 |
| UV | 2,460 | 695 | 325 | 186 | 124 |
| Full | 12,730 | 3,310 | 1,436 | 845 | 545 |
Control Board Operation
Menu Map
| Menu Item | Action | Value/Option | Function |
|---|---|---|---|
| Addr | ➡️ | d 0-255 | Select DMX address |
| CHNL | ➡️ | CH-1 or CH-2 | Select DMX channel mode (CH-1: 6ch / CH-2: 11ch) |
| SP-- | ➡️ | SP 0 - SP99 | Set program speed |
| Pr-- | ➡️ | Pr 1 - Pr 13 | Select built-in program |
| SOUN | ➡️ | Sou | Select sound active mode |
| Colo | ➡️ | C 0 - C 255 | Select static colour mode (See static colour mode chart below) |
| Strb | ➡️ | 5.00 - 5.20 | Set strobe speed (Hz) |
| FL-- | ➡️ | r 0 - r255 | Set red colour intensity |
| GL-- | ➡️ | G 0 - G255 | Set green colour intensity |
| BL-- | ➡️ | B 0 - B255 | Set blue colour intensity |
| UL-- | ➡️ | U 0 - U255 | Set white colour intensity |
| PL-- | ➡️ | P 0 - P255 | Set amber colour intensity |
| nOdE | ➡️ | nod0 or nod4 | Set dimmer speed (nod0: fastest / nod4: slowest) |
| LED | ➡️ | OFF or ON | Toggle LED display on / off |
| UErn | ➡️ | [Enter button press] | Long press "Enter" button to show current temperature |
| rStE | ➡️ | U01 or YES | Restore settings to factory default |
Static Colour Mode
| Value | Function |
|---|---|
| C1 | Red |
| C2 | Green |
| C3 | Red+Green |
| C4 | Blue |
| C5 | Blue+Red+UV |
| C6 | Green+Blue |
| C7 | Red+Green+Blue+Amber+UV |
| C8 | White |
| C9 | Red+White |
| C10 | Green+White |
| C11 | Red+Amber |
| C12 | Blue+White+UV |
| C13 | Red + Blue+White+UV |
| C14 | Red + Blue+White |
| C15 | Red+Green+Blue+White+Amber+UV |
DMX Chart
6 Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000-255 | Red: 0% ~ 100% |
| 2 | 000-255 | Green: 0% ~ 100% |
| 3 | 000-255 | Blue: 0% ~ 100% |
| 4 | 000-255 | White: 0% ~ 100% |
| 5 | 000-255 | Amber: 0% ~ 100% |
| 6 | 000-255 | UV: 0% ~ 100% |
11 Channel Mode
| Channel | Value | Function | Note |
|---|---|---|---|
| 1 | 000-255 | Master Dimmer 0% ~ 100% | |
| 2 | 000-255 | Red: 0% ~ 100% | |
| 3 | 000-255 | Green: 0% ~ 100% | |
| 4 | 000-255 | Blue: 0% ~ 100% | |
| 5 | 000-255 | White: 0% ~ 100% | |
| 6 | 000-255 | Amber: 0% ~ 100% | |
| 7 | 000-255 | UV: 0%~100% | |
| 8 | 000-011 | Strobe OFF | |
| 012-255 | Strobe (slow-fast) | ||
| 9 | 000-009 | No Function | |
| 010-019 | Program 1 | ||
| 020-029 | Program 2 | ||
| 030-039 | Program 3 | ||
| 040-049 | Program 4 | ||
| 050-059 | Program 5 | ||
| 060-069 | Program 6 | ||
| 070-079 | Program 7 | ||
| 080-089 | Program 8 | ||
| 090-099 | Program 9 | ||
| 100-109 | Program 10 | ||
| 110-119 | Program 11 | ||
| 120-129 | Program 12 | ||
| 130-139 | Program 13 | ||
| 140-255 | Sound active mode | Ch9 must be set between 10-139 | |
| 10 | 000-255 | Speed of auto programs (slow ~ fast) | |
| 11 | 000-255 | Colour fade time (jump ~ fade) | Mode must be set to "nod0" |
IR Remote
To use the IR Remote, the PAR19X12L must be in DMX mode without an active DMX connection. If a DMX signal is received, the PAR19X12L will prioritise the DMX signal and ignore the IR Remote.
- Use ON/OFF to turn PAR19X12L on or off. The current IR settings will be saved automatically when PAR19X12L is powered off and reloaded when it is turned on again. To reset to the factory default Blackout mode, long press Off.
- Press R/G/B/W/A/U to light up the LEDs in red, green, blue, white, amber, or UV respectively.
- Press a number 0-9 in the orange shaded area to select a pre-set colour.
- Press + to increase the intensity of the selected colour and - to decrease the intensity of the selected colour.
- Press Auto/Sound/Strobe to switch on or off Auto mode, Sound Active mode, and Strobe mode, respectively.
- Press Blackout to clear all the remote settings and blackout PAR19X12L.
IR Remote Layout:
Power: ON, OFF
Color Select: R, G, B, W, A, UV
Presets: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9
Control: +, - (Intensity), AUTO, SOUND, STROBE, BLACKOUT
Technical Specifications
Photometrics
- Light Source: 19x 12W RGBWAU 6-in-1 LEDs
- Beam Angle: 40°
- PWM: 20,000 Hz
- LED Lifespan: 50,000 hours
Effects
- Dimming: 0~100%
- Strobe: 1 - 20 Hz
Power
- Input Voltage: 100~240V AC, 50/60Hz
- Power Consumption: 100W
- Connection: powerCON in/out
Control
- Protocol: DMX512
- DMX channels: 6/11
- Interface: 3-pin DMX in/out
- Built-in Programming: Yes
- Display: 4-button and 4-digit LED control panel
- Operation Modes: DMX, manual, auto, sound active, IR remote, master/slave
Housing
- Materials: Die cast aluminium, matte black finish
- Cooling: Fanless Cooling
- Net weight: 2.8 kg
- Overall Size: 275x270x84 mm
Warranty
Please contact your local Kookaburra Account Manager.
