Event Lighting F200VW Variable White Fresnel with Manual Zoom
User Manual
Version 3.1 (08.07.2025)
Safety Instructions
WARNING
- Do not open this device; there are no user-serviceable parts inside. Risk of electric shock.
- Do not look at the light source when the device is on.
CAUTION
- This unit's housing may be hot during and after operation.
- Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
- Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
- Use a safety chain when mounting this device overhead.
- Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
- Do not operate this device if the housing, lenses, or cables appear damaged.
- Do not connect this device to a dimmer or rheostat.
- ONLY connect this device to a grounded and protected circuit.
- ONLY use the hanging bracket to carry this device.
- In case of a serious operating problem, stop using immediately.
- The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply working with input voltage range of 100~240 VAC, 50/60 Hz. Link up to the maximum 8A. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations, provided each individual device is secured by the use of the correct mounting bracket. Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device blows, only replace the fuse with a fuse of the same type and rating. Before replacing the fuse, unplug the mains lead.
Procedure:
- Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
- Remove the old fuse from the fuse holder.
- Install the new fuse in the fuse holder.
- Replace the fuse holder in the housing and fix it.
Diagrams
Lux Chart
Lux @20°
| Distance From Source | 1m / 3'3" | 2m / 6'7" | 3m / 9'10" | 4m / 13'2" |
|---|---|---|---|---|
| 2600K | 13,065 | 3,300 | 1,530 | 844 |
| 6600K | 17,950 | 4,670 | 2,216 | 1,185 |
| Full | 30,170 | 7,816 | 3,550 | 1,993 |
| Diameter | Ø0.36m / 1'2" | Ø0.72m / 2'4" | Ø1.08m / 3'7" | Ø1.44m / 4'9" |
Lux @53°
| Distance From Source | 1m / 3'3" | 2m / 6'7" | 3m / 9'10" | 4m / 13'2" |
|---|---|---|---|---|
| 2600K | 3,770 | 1,010 | 445 | 255 |
| 6600K | 5,265 | 1,395 | 612 | 355 |
| Full | 8,865 | 2,345 | 1,025 | 596 |
| Diameter | Ø0.99m / 3'3" | Ø1.98m / 6'6" | Ø2.96m / 9'9" | Ø3.95m / 12'12" |
Visual representation of light spread: A diagram shows a light source emitting a beam that widens with distance. Four vertical lines indicate distances of 1m, 2m, 3m, and 4m, with elliptical shapes representing the light coverage at each distance, showing how the beam diameter increases.
Dimensions
The following diagrams illustrate the physical dimensions of the F200VW fixture:
- Front View: Shows a circular fixture with a diameter of 200mm.
- Side View: Shows a depth of 166.8mm.
- Top/Bottom View: Shows a circular fixture with a diameter of 200mm, and an overall height/depth of 217.5mm.
- Another side view shows the fixture with barn doors attached, indicating a depth of 166.8mm and a diameter of Ø180mm for the lens assembly.
Control Board Operation
The F200VW features a 4-button LCD control panel for operation.
Control Board Functions
| Display | Options / Values | Function |
|---|---|---|
| DMX Add | <001> - <508> | To set DMX address |
| DMX Cha | <01>, <1U><02>, <05>,<07><User> | To set DMX channel modes |
| DMXLoss | <Hold><Blackout><Manual> | Select mode when DMX loss |
| UserDMX | CH:<01> End | Edit a user DMX mode |
| Manual | Preset <StrawW> <WarmW> <White> <CoolW> <Steel> | To select colour from 5 preset colour temperature modes |
| Finetune <Straw> <Straw+> <Stra++> <--Warm> <-WarmW> <WarmW> <WarmW+> <Warm++> <--Whit><-White> <White> <White+> <Whit++> <--Cool> <-CoolW> <CoolW> <CoolW+> <Cool++> <--Stee> <-Steel> <Steel> | To select colour from 21 fine tune colour temperature modes | |
| Dimmer <000> - <100> | To set dimming intensity | |
| Mas/Sla | < Sla> / <Mas> | To set Master/Slave modes |
| Wireless | <ON><OFF> <EL Mode> <W-DMX_R> <W-DMX_T> | You need to install WDMX module inside the fixture first and then receive the DMX signal from the transmitter attached to the console by setting this on |
| Reset | <N>/ <Y> | To reset factory default setting |
| Update | <N>/ <Y> <START> | Select to update firmware Use this fixture to update another fixture's software |
DMX Addressing
After selecting the "DMX Add", press "Enter". Use "Up" and "Down" buttons to select the desired DMX address, then press "Enter" to save the new setting.
DMX Modes
After selecting the "DMX Cha", press "Enter". Use "Up" and "Down" buttons to select the desired DMX mode, then press "Enter" to save the new setting.
DMX Loss
This feature allows users to set the behavior when DMX signal is lost.
- By default, if in DMX mode and no signal is received, the fixture will hold its current state. If a DMX signal is received and then lost, it will hold the last received signal.
- Users can select from options like Hold (hold last signal), Blackout, Manual (last manual colour), or Auto (last Auto show selected).
User DMX
This function allows users to define custom DMX modes. Users can select channels and assign functions. For example, selecting 'User DMX' allows channel selection and rearrangement. Setting an 'End' channel stops the sequence. If 10 channels are desired, the 11th channel acts as 'End', creating a 10-channel user mode. This mode is then selected under DMX Channel mode as 'User'.
Manual Mode
After entering "Manual" mode, use the "Up" and "Down" buttons to select colours from preset groups and fine-tune groups. Set intensity from 000 to 255, then press "Enter" to save.
Master/Slave
Set the master fixture to one of the standalone operating modes. To set a slave fixture, enter "Mas/Sla" mode, set it to "Slave", and press "Enter" to save the setting.
Firmware Update
Use fixture A to update fixture B's firmware:
- Set fixture A to "Update" mode, select "Y", then select "START".
- Link fixture A and fixture B with a DMX cable, then power up fixture B.
- Press "Enter" on fixture A; fixture B's firmware will be copied from fixture A.
Note: Ensure fixture A and B are of the same type to avoid damage. Only fixtures A and B should be in the DMX chain during firmware updates.
DMX Chart
The following tables detail the DMX channel assignments for different modes:
1 Channel Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000 - 255 | Dimmer & Colour temperature |
1U Channels Mode
| Channel | Value | Function |
|---|---|---|
| 1U | 000 - 255 | Dimmer (dim the preset color selected in Menu) |
2 Channels Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000 - 255 | Dimmer 0% ~ 100% |
| 2 | 000 - 255 | Warm white to cool white |
5 Channels Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000-255 | Master dimmer coarse: 0% ~ 100% |
| 2 | 000 - 255 | Master dimmer fine: 0% ~ 100% |
| 3 | 000 - 255 | Warm white to cool white |
| 4 | 000-015 | No function(Shutter on) |
| 016-119 | Strobe slow to fast (1-25Hz) | |
| 120 - 127 | Shutter on | |
| 128-183 | Strobe random slow to fast | |
| 184-191 | Shutter on | |
| 192 - 247 | Strobe audio sensitivity low to high | |
| 248-255 | Shutter on | |
| 5 | 000-050 | Standard |
| 6 | 051-101 | Stage |
| 102 - 152 | TV | |
| 153-203 | Architect | |
| 204-255 | Theater |
7 Channels Mode
| Channel | Value | Function |
|---|---|---|
| 1 | 000 - 255 | Master dimmer coarse: 0% ~ 100% |
| 2 | 000-255 | Master dimmer fine: 0% ~ 100% |
| 3 | 000-255 | Warm White |
| 4 | 000-255 | Cool White |
| 5 | 000-015 | No function(Shutter on) |
| 016-119 | Strobe slow to fast (1-25Hz) | |
| 120-127 | Shutter on | |
| 128-183 | Strobe random slow to fast | |
| 184-191 | Shutter on | |
| 192 - 247 | Strobe audio sensitivity low to high | |
| 248 - 255 | Shutter on | |
| 6 | 000-009 | No function |
| 7 | 010-255 | Preset Colours (Warm->Cold) |
| 000-050 | Standard | |
| 8 | 051-101 | Stage |
| 102-152 | TV | |
| 153-203 | Architect | |
| 204-255 | Theater |
Technical Specifications
Power
- Power Supply: 100~240V AC, 50/60 Hz
- Power Consumption: 120W
- Power Connection: Seetronic in / out
Photometrics
- Light Source: 1 x 100W*2 cool white 6500K and warm white 2700K COB LED
- CRI: 95+
- Beam Angle: 20° - 53°
- Field Angle: 34° - 70°
- Output: 3550 lux @3M at 20°, 1025 lux @3M at 53°
- Lens: 80mm Planconvex lens
- PWM: 1,200Hz
- LED Lifespan: 50,000 hours
Effects
- Dimming: 16-bit 0 - 100%
- Strobe: 1 - 25 Hz
- Zoom: Manual Zoom 20° to 53°
- Barn Door: Included
- Gel Clip: Included
Control
- Operational Modes: Manual, Master / Slave & DMX, WDMX, RDM
- Display: 4-button LCD control panel
- DMX Protocol: DMX512
- DMX Channel Mode: 1 / 1U / 2 / 5 / 7 / User
- DMX Interface: 5-pin XLR (Optional 3-pin XLR)
Housing
- Housing Materials: Die-cast Aluminum Housing
- Housing Finishing: Matte Black
- Cooling: Fanless Cooling with Temperature Protection
- Net Weight: 3.2 kg
- Dimension: 217.5 X 167 X 200mm
Warranty
Details regarding the product warranty are provided.
