Innokin Klypse Mecha Refillable Pod Kit Quick Guide
Brand: Innokin
Product Type: Refillable Pod Kit
Components
The Innokin Klypse Mecha is a refillable pod kit. Key components include:
- Pod: The refillable cartridge for e-liquid. It has a capacity of 2mL.
- Fill Port: Located on the pod for refilling e-liquid.
- Smart Mode: The device automatically adjusts to the supported power range of your pod for optimal performance.
- Battery: The integrated power source for the device.
- AirFlow Control: Allows adjustment of the airflow.
- Rotating Button: Used for navigation and adjustments.
- OLED Display: Shows device information.
- USB-C Charging Port: For charging the device.
Diagram Description: A detailed illustration of the Klypse Mecha device shows its rectangular form with intricate mechanical designs featuring gears and circular elements. Labels point to the Pod, Fill Port, AirFlow Control, Rotating Button, OLED Display, Battery, and USB-C Charging Port. The pod itself is a smaller cartridge with a fill port.
Interface
The device features an OLED display showing:
- Mode: Displays current mode (e.g., Wattage).
- Battery Level Ring: A visual indicator of the battery charge.
- Coil Resistance: Shows the resistance of the installed coil (e.g., 0.60Ω).
- Puff Timer: Displays the duration of the last puff (e.g., 00.0s).
- Screen Lock: Indicates if the screen is locked.
- Time Display: Shows the current time (e.g., 2:30, 14:30).
How to Use
How to Fill:
- Fill the pod: Pull the tab to open and add E-liquid.
- Insert the pod into the device and simply puff to start your vaping experience.
Warning: Wait at least 5 minutes (≥5min) after filling a new pod with e-liquid so the cotton can be saturated with e-liquid before use.
Operations
- ON/OFF: 3x Clicks within 2 Seconds.
- To Lock/Unlock the Screen: Press and hold the button for 3 seconds to lock or unlock the screen. When locked, you can vape but cannot make adjustments.
- Menu Settings:
- Press the button twice to access the menu.
Menu Navigation: The interface shows a flow from the main menu (MENU, COIL, SETTINGS, CUTOFF, BACK) to sub-menus like COIL (WATTAGE, VOLTAGE, BACK) and SETTINGS (TIME, SCREEN, QUERY, BACK), and CUTOFF (7S, BACK).
- Coil Settings (Wattage/Voltage Adjustment):
- Press and hold for 1 second until numbers start flashing to access adjustment mode.
- Rotate the button to increase or decrease the voltage/wattage. Each left turn reduces the value by 0.1V/0.5W, and each right turn increases it by 0.1V/0.5W.
- Cutoff Time: Vape cutoff time can be adjusted (3-10 seconds).
Charging & Safety
Battery Level Indicator:
- Battery 10%-30%: Yellow light ?
- Battery ≤ 10%: Red light ?
- Battery ≥ 30%: Green light ?
Charge promptly based on the battery level ring. While charging, a lightning bolt icon displays on the screen and the battery ring will fill. When fully charged, the screen displays 100%.
Cautions:
- Charge with a certified 5V wall charger and USB-C cable.
- DO NOT leave the device unattended when charging.
- DO NOT store the device with a depleted battery.
- Keep the device away from direct sunlight and excessive heat.
Protections
- Low Volt : Warning displayed when battery voltage is too low. Solution: Charge the device.
- Check Coil : Warning displayed when load exceeds 3.5 ohms or there is no load. Solution: Check pod connection or replace pod.
- Coil Low : Warning displayed when load is short-circuited or below 0.5 ohms. Solution: Check or replace the pod.
- Coil Short : Warning displayed when there is a short circuit. Solution: Check or replace the pod.
- Time Out : Warning displayed when exceeding 10 seconds of vaping. Solution: Wait 2 seconds before vaping again.
- High Temp : Warning displayed when PCB temperature is too high. Solution: Wait for the device to cool down before vaping again.
Specifications
- Dimensions: 94.2 x 42.7 x 17 mm
- Pod: 2mL / 0.6Ω
- Voltage: 1.0-4.5V
- Wattage: 6-18W
- Activation: Puff Activated Auto-Draw
- Cut-off Time: 3-10s
- Battery Capacity: 900mAh
- Charging Specifications: DC5V / 0.8A
Contact & Manufacturer Information
For any questions, contact support@innokin.com.
Follow Innokin on social media:
- Facebook: facebook.com/Innokin.Technology
- Instagram: instagram.com/innokintechnology
- Twitter: twitter.com/innokintech
- Reddit: reddit.com/r/innokin
Manufacturer: Shenzhen Innokin Technology Co., Ltd.
Address: 1st-5th Floor, Building 6, Xinxintian Industrial Park, Xinsha Road, Shaer Community, Shajing, Baoan District, 518104, Shenzhen, China.
Telephone: +86 755 29898770
Email: info@innokin.com
European Representative: FRANCE VAPOTAGE DISTRIBUTION
Address: 57 impasse de la Ferme Cardon, Rue de la Croix Bougard 59810 LESQUIN France
Telephone: +33 320020152
Email: guillaume.vilain@innokin.fr
Certifications: ISO 9001/14001/45001, ISO 13485, and cGMP Certified.
Important Safety Notice: KEEP OUT OF REACH OF CHILDREN. (Icons: -18, Recycling, RoHS, UKCA, CE, WEEE)
