Innokin Endura V Pro Quick Guide
Thank you for choosing an original Innokin product. Please read this guide carefully for correct and safe usage.
Components
The Innokin Endura V Pro consists of the following parts:
- Mouthpiece
- Fill port
- Pod
- Display
- On/off Switch
- USB-C Charge Port
- Airflow Control
- Power Button
- Built-in Battery
Fill and Install the Pod
- How to fill: Remove the black mouthpiece to reveal the top-fill section and carefully add e-liquid. Ensure the mouthpiece is replaced securely after filling.
Important: Wait for at least five minutes after filling to allow the new pod to saturate with E-liquid. Vaping before this time may burn the coil. Do not allow the pod to be completely depleted of E-liquid. Refill it regularly to avoid dry hits and prolong coil life.
- Insert the magnetic pod into the device.
Adjusting the Airflow
Adjust the airflow control for your desired draw.
Lock/unlock the device
Toggle the on/off switch to lock or unlock the device. In the locked state, the device disables button-activated vaping and wattage adjustment.
Power On/Off the Device
Press the power button five times consecutively to power the device on or off.
Home Screen
The home screen displays the following information:
- Screen Lock Status
- Wattage
- Coil Resistance
- Battery Ring (indicating battery level: <10%, 10%-30%, 30%-99%, 100%)
Puff Time
While vaping, the duration of your current draw will be displayed in seconds.
Wattage Adjustment
- Press the power button three times consecutively until the numbers start flashing to enter wattage adjustment mode.
- Press the power button to adjust the wattage in 1.0W increments with a full range of 6-35W (coil dependent).
- Wait for five seconds to exit the wattage adjustment mode.
Charging
- Charge promptly based on battery level. Do not allow the battery to stay under 10% or above 90% for extended periods.
- Use a standard output charger and charging cable with the correct charging current and voltage range.
Caution
- Turn the device off when not in use to avoid depleting the battery and minimize excessive battery wear.
- Avoid dropping, throwing, or mishandling the device to prevent damage.
- Protect the device from direct sunlight, heat, dust, moisture, or mechanical shock.
- Keep the device away from any water, liquid, or flammable gas.
- Keep the contents of this package out of reach of children, non-smokers and animals.
- Do not leave the device charging while unattended.
- Do not use it if pregnant or breast feeding.
- Warning: Do not use this product if you suffer from heart disease, severe hypertension, diabetes, stomach ulcers or have a history of seizures.
Specifications
- Dimensions: 124.3×27.6×16.8 mm (2mL pod included) / 127.3×27.6×16.8 mm (3mL pod included)
- Pod Capacity: 2.0mL / 3.0mL
- Compatible: Vcap Pod 0.4Ω / 0.6Ω / 0.8Ω / 1.2Ω
- Output Power: 6.0~35.0W
- Battery Capacity: 1200mAh
- Charging Current: DC 5.0V/900mA
- Activation: Draw-activated Vape / Button-activated Vape
Protections
- LOW VOLT: Warning is displayed when the battery voltage is too low. Solution: Charge the device.
- CHECK COIL: Warning is displayed when the load exceeds 3.5 ohms or when there is no load. Solution: Check the connection of the pod or replace the pod.
- TIME OUT: Warning is displayed when you exceed 8 seconds of vaping. Solution: Wait for 2 seconds before vaping again.
- HIGH TEMP: Warning is displayed when the PCB temperature is too high. Solution: Wait for the device to cool down before vaping again.
- COIL SHORT: Warning is displayed when there is a short circuit. Solution: Check the pod connection or replace the pod.
- LOW RES: Warning is displayed when the coil resistance is too low before vaping. Solution: Check the pod connection or replace the pod.
EEE Recycling
This product is meant to be disposed of in an approved e-waste receptacle or recycling bin. Do not throw it away in standard waste receptacles.
Manufacturer Information
Manufacturer: Shenzhen Innokin Technology Co., Ltd.
Address: 1st-5th Floor, Building 6, Xinxintian Industrial Park, Xinsha Road, Shaer Community, Shajing, Baoan District, 518104, Shenzhen, China.
Telephone: +86 755 2989 8770
Email: info@innokin.com
Website: www.innokin.com
European Representative: FRANCE VAPOTAGE DISTRIBUTION, 68 rue d'ennevelin 59710 Avelin France, Telephone: +33 320020152, Email: Contact@innokin.fr
