Eufy SoloCam S340 Quick Start Guide

At a Glance

The Eufy SoloCam S340 features the following components:

• 1. LED Indicator: Provides visual status information.
• 2. Speaker: For audio output.
• 3. Telephoto Lens: For zoomed-in views.
• 4. Photosensitive Sensor: Adjusts camera settings based on light.
• 5. PIR Sensor: Detects motion.
• 6. Microphone: For audio input.
• 7. Wide-Angle Lens: For a broader field of view.
• 8. LED Light: Provides illumination.
• 9. Solar Panel Mounting Hole: For attaching the solar panel.
• 10. Mounting Hook: For securing the camera mount.
• 11. USB-C Charging Port: For charging the device.
• 12. SYNC Button: Used for synchronization.

Charging Your Camera

Fully charge the camera before first use.

Charging Indicator:

• Solid Blue: Charging
• Light Off: Fully Charged

Charging Time: Approximately 8 Hours

Diagram: Shows a USB-C cable connecting a power adapter to the camera's USB-C port.

Setting Up the System

1. Download and install the Eufy Security app from the App Store or Google Play. Sign in or create an account.
2. Follow the in-app instructions to add the camera to your device list.

Diagram: Shows the Eufy Security app icon and buttons to download from the App Store and Google Play. Another diagram shows a smartphone with a Wi-Fi signal connecting to the camera.

Mounting Your Camera

Select a Location and a Height

Choose a location that provides the desired view. It is recommended to mount the camera 7-10 ft (2-3 m) above the ground.

Diagram: Illustrates mounting the camera on the side of a house, showing the recommended height and a range of up to 32 ft (10m) detection distance.

To ensure no detection is missed, do not install the camera directly facing the monitoring area. Instead, angle it to avoid blind spots.

Diagram: Shows two scenarios for camera angling. The top diagram shows a correct angled view with a checkmark. The bottom diagram shows a camera facing directly forward with a cross mark, indicating a potential blind spot.

Select a Solar Panel Location

Option 1: Mount the Camera and the Solar Panel Separately (Best for Strong Solar Power)

If the camera's view is obstructed, mount the solar panel independently using the provided USB-C extension cable for optimal solar charging. The camera can be mounted on a wall or ceiling.

Diagram: Shows the solar panel mounted separately on a wall, connected to the camera below.

1. Drill holes using a 15/64 inch (5.95 mm) drill bit with the provided positioning card, then insert anchors.
2. Connect the solar panel to the camera using the provided USB-C extension cable.
3. Firmly secure the camera onto the mounting bracket.

Diagrams: Illustrate drilling holes, inserting anchors, connecting the USB-C cable, and attaching the camera to the bracket with screws. Shows correct and incorrect mounting angles with checkmarks and cross marks.

Option 2: Mount the Camera with the Solar Panel Attached (Less Drilling)

If the camera's view is not obstructed, attach the solar panel directly to the top of the camera.

Diagram: Shows the solar panel attached directly to the top of the camera.

1. Secure the solar panel's mounting bracket to the top of the camera.
2. Install the solar panel onto its mounting bracket by turning it.
3. Connect the USB-C connector to the USB-C port of the solar panel.
4. Drill holes with a 15/64 inch (5.95 mm) drill bit with the included positioning card, then insert the anchors into the holes.
5. Firmly secure the camera onto the mounting bracket and adjust the angle (20°–30° recommended).

Diagrams: Illustrate attaching the solar panel bracket, connecting the USB-C cable, drilling holes, and mounting the camera with the solar panel attached at an angle.

Safety

• Suitable temperature range: -20°C to 50°C (Charging temperature: 0°C to 40°C).
• Avoid using the device in environments exceeding recommended temperatures or in excessively wet conditions, unless specified otherwise in the user guide.
• Recommended operating temperature: 5°C to 25°C.
• Ensure good ventilation when the device is powered.
• CAUTION: Risk of explosion if an incorrect battery type is used. Dispose of used batteries according to instructions.
• ATTENTION: IL EXISTE UN RISQUE D'EXPLOSION EN CAS D'UTILISATION D'UN TYPE DE PILE INCORRECT. ÉLIMINEZ LES PILES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

Warning:

• Replacing a battery with an incorrect type can bypass safeguards and create danger.
• Disposal of a battery in fire, high heat, or by crushing/cutting may result in explosion and leakage of flammable liquids and gases.
• Leaving a battery in extremely hot environments may result in explosion and leakage of flammable liquids and gases.
• A battery subjected to extremely low air pressure may result in explosion and leakage of flammable liquids and gases.

Attention (French):

• Le remplacement d'une batterie par un type incorrect peut contourner les protections et créer un danger.
• L'élimination d'une pile dans un feu ou une autre source de chaleur importante, ou par écrasement ou découpage, peut entraîner une explosion ainsi qu'une fuite de liquides et de gaz inflammables.
• Le fait de laisser une batterie dans un environnement extrêmement chaud peut entraîner une explosion ainsi qu'une fuite de liquides et de gaz inflammables.
• Une batterie soumise à une pression d'air extrêmement faible peut provoquer une explosion ainsi qu'une fuite de liquides et de gaz inflammables.

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by:

1. Reorienting or relocating the receiving antenna.
2. Increasing the separation between the equipment and receiver.
3. Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consulting the dealer or an experienced radio/TV technician.

FCC Radio Frequency Exposure Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The minimum separation distance is 20 cm.

Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

The following importer is the responsible party:

Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: 1-800-988-7973

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RF Statement: When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d'exposition RF.

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol ♻️ means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

Customer Service

• 12-month limited warranty
• Contact Numbers:
  • (US) +1 (800) 988-7973
  • (UK) +44 (0) 1604 936200
  • (DE) +49 (0) 69 9579 7960
  • (China) +86 400 0550 036
  • (Japan) +81 03 4455 7823
  • (AU) +61 3 8331 4800
  • (Egypt) +20 8000000826
  • (UAE) +971 8000320817
  • (Kuwait) +965 22069086
  • (Saudi Arabia) +966 8008500030
• Email: support@eufy.com

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

Follow us:

• Facebook: @EufyOfficial
• Instagram: @EufyOfficial
• Twitter: @EufyOfficial