Explosion Diagram Specification
The following table details the components of the device:
| Item | Part Name | Item | Part Name |
|---|---|---|---|
| 1 | CTP+LCM 6.95FHD | 2 | F HSG ASM |
| 3 | PCBA MB | 4 | MAIN WATERPROOF FRAME ASM |
| 5 | CAM AF 50M | 6 | PS RUBBER |
| 7 | CAM FF 2M | 8 | CAM FF 8M |
| 9 | CAM FF 8W | 10 | F CAM FRAME ASM |
| 11 | LCM CONN WATERPROOF RUBBER | 12 | BAT CONN WATERPROOF RUBBER |
| 13 | SCREW SEAL MYLAR | 14 | UP SPK CON COP FOIL |
| 15 | F CAM COP FOIL | 16 | REC DECO PART |
| 17 | MAIN WATERPROOF MYLAR | 18 | MAIN RADIATING FILM |
| 19 | R MAIN CAM CON FOAMS | 20 | MAIN SHIELD COP FOIL |
| 21 | R MAIN CAM LENS | 22 | R VICE CAM LENS |
| 23 | R VICE CAM LENS | 24 | R VICE CAM CON FOAMS |
| 25 | R CAM RUBBER 8W | 26 | R VICE CAM RUBBER 2M |
| 27 | MC SCREW L3.5 | 28 | MC SCREW L2.5 |
| 29 | MI HOUSING | 30 | BAT COVER ASM |
| 31 | MOTOR LINEAR | 32 | PCBA SUB |
| 33 | FPC ESD POAM | 34 | SPK |
| 35 | EARPHONE RUBBER | 36 | FM |
| 37 | COAXIAL CABLE | 38 | FPC MAIN |
| 39 | FPC BAT COVER RGB LIGHT | 40 | USB RUBBER |
| 41 | FPC SIDE KEY | 42 | BAT |
| 43 | R CAM DECO ASM | 44 | CAM LOCATION FRAME ASM |
| 45 | DOWN FRAME ASM | 46 | BAT COVER RADIATING FILM |
| 47 | CARD HOLDER |
Know Your Phone
The following are the key external features of the phone:
- 1. Front camera
- 2. Volume + key
- 3. Volume - key
- 4. Power key
- 5. Breathing Light
SIM/SD Card Installation
To install a SIM or SD card:
- Power off the mobile device.
- Refer to the provided diagrams for correct SIM/SD card placement.
Charging the Phone
The device can be charged using a TECNO-approved charger and cable, or by connecting to a computer via a USB cable. Using unapproved chargers or cables may damage the device and void the warranty.
FCC Caution
Labelling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: LF7 (FCC ID: 2ADYY-LF7) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.17 W/kg, and when properly worn on the body is 0.78 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
System Information
HiOS runs on Android™ OS. Android is a trademark of Google LLC.
